Toshiba Projector Tlp S71 User Manual

							21
20
Preparations
COMPUTER-(
Y/PB/PR )
S-VIDEO VIDEOVIDEO
AUDIO
MONITOR
CONTROL
p48
Before connection•Read the owner’s manual of the device to connect to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.46
, etc.
•Turn off the power of both devices before connecting.
•The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Note
•The AUDIO terminal can be used with all the devices for input terminal.Connection
Computer
CRT monitor, etc.
To audio output
Audio cable
(for computer)
(*supplied)To RGB
output
Control cable
To RS-232C terminal RGB cable
(supplied)
To  Y / C
B/CR output
Green (Y)
Blue (CB),
Red (CR)
Yellow
(to video output)
To audio
output
White (L)
Red (R)
VCR
S-Video cable
(not supplied)
Video cable
(*supplied)
To S-Video
output
To audio
output
White (L)
Red (R)
Computer (for control)
Conversion
adapter
BNC-pin
(not supplied)
Monitor cable
Mini D-sub 15P-BNC
(not supplied)
Audio cable
(*supplied)
DVD player
a (min length) = projection size (inches) – 1.547
26.44a (max length) = projection size (inches) – 1.2907
22.06
90
a
90
Projection Distance and Screen Size (with optical zooming)Use the figures, tables, and formulas below to determine the screen size and projection
distance. (Screen sizes are approximate values for full-size picture with no keystone adjust-
ment)a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.45 m to 11.29 m.
Screen
As seen from above
Lens center
As seen from the side
a (min length) = projection size (inches) – 1.4285
30.68a (max length) = projection size (inches) – 1.1908
25.574
a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.26 m to 9.73 m. For TLP-T70M/T71M/S70/S71
For TLP-T60M/T61M/S40/S41
screenprojection distance a(m)
min length max lengthsize (cm)
(zooming max) (zooming min)40 (102) 1.45 1.7560 (152) 2.21 2.6680 (203) 2.97 3.57100 (254) 3.72 4.47150 (381) 5.61 6.74200 (508) 7.51 9.01250 (635) 9.40 11.27
300 (762) 11.29—
screenprojection distance a(m)
min length max lengthsize (cm)
(zooming max) (zooming min)40 (102) 1.26 1.5260 (152) 1.91 2.3080 (203) 2.56 3.08100 (254) 3.21 3.86150 (381) 4.84 5.82200 (508) 6.47 7.77250 (635) 8.10 9.73
300 (762) 9.73—
Placement (Continued)
*Audio cable (for computer), Audio cable and Video cable are not supplied with TLP-S70/S71. 
						

							23
Operations
22

 Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling is completed
FAN TEMP LAMP ON
FAN TEMP LAMP ON
AFAN TEMP LAMP ON
B
C
(Green) (Green) (Orange)
Flashing(Green) (Off) (Orange)(Off) (Off) (Orange)
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord in this state will shorten
the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord in this state.
C
In standby mode.
Note
• The projector consumes about 6W of power in standby. We recommend you to unplug the
power cord if you will not use the projector for an extended period.
PRECAUTIONS
• Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging
the power cord and cutting off the power while the projector is running or being cooled
will shorten the life of the lamp. However, please unplug the power cord if the
projector locks up or acts abnormally.
• If the power cord was unplugged before cooling was complete, give the lamp sufficient
time to cool before plugging it back in. If the lamp overheats, it may fail to light, and its
lifetime will be shortened.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
• In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time 
p.39
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.

 Connecting the power cord1
Insert the power cord connector into the AC IN socket of the projector.
2
Insert the power cord plug into a wall or other power outlet.

 Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.

 Turning the power on
Press the ON/STANDBY
button.The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-
up screen appears. WARNING• Do not look into the lens during operation. Doing so could damage your vision. CAUTION•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.• Do not place your hands, face, or other objects near the air exhaust. Doing so could
cause burns, deform/break the object.Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen before this
by performing any operation. You can also configure the start-up screen not to appear via the
Display setting menu 
p.33
.
• The first time you use the projector after purchase, after the start-up screen disappears, the
Language menu is displayed p.24
.
When the power cord is plugged in, the following
three green indicators will come on for several
seconds: ON, TEMP, and LAMP. Next, the ON
indicator will change to orange, indicating standby
mode.
(Do not perform any operations while the 3 green
indicators are on.)
(Supplied) Power cord connector
Control panelRemote
Control
Turning the power on and offOperations
FA NTEMPLAMPON
VOL.
 +
VOL . -
ON / STANDBY INPUT
MENU
AUTO SE T ZOOM +
ZOOM -
AU TO
KEYSTONE
INPUTON/
STANDBY
RESIZE
OFFCALL
AU TO
MUTE
RESIZEFREEZE SET
KEYSTONE 
						

							25
Operations
24
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTurn the foot adjuster to fine-tune
the angle.
eTo adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6
Adjusting the picture size and focusqUse the zooming lever to adjust the screen
size.
wUse the focusing ring to adjust the focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes
•Note that because of the lamp characteristics, the brightness of the lamp may fluctuate slightly
.
• A lamp is a consumable supply.
If used for extended periods, images will appear dark, and the lamp could burn out.  This
is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on
conditions of use.)
• The LCD panel is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
•
Although this projector supports a wide range of RGB signals 
p.46
, any resolutions not
supported by the model (XGA or SVGA, depending on the model) will expand or shrink the
pictures, and will affect image quality slightly. To view high-quality images, it is
recommended that the computer’s external output should be set to the projector’s resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may cause the images to be
shown improperly. If this happens, turn off the computer’s LCD display. For information on
how to turn off the LCD display, see the owner’s manual of your computer.
• If a signal not supported by the projector is input, the 
 icon will appear.
• If a no signal is being input from the connected device, the 
 icon will appear.
• If an unavailable operation button is pressed, the 
 icon will appear.
1
3
2
1
2
1
Turn on the power.Turn on the power by following the instructions in “Turning on the power” 
p.22
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 
6.)
qUse the 
 or 
 buttons to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
wUsing the 
 or 
 button, select Standard
or Low and press the 
 button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes•When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Reset menu 
p.33
, the Language and Lamp power menus will be displayed the next
time when the power is turned on
•The language can also be set via the Display setting menu 
p.33
 and Lamp power
via the Default setting menu 
p.32
.
•This owner’s manual assumes that English has been selected.
3
Place connected device(s) in operating status.Turn on and boot up connected computers and other devices.
4
Select input.qPress the INPUT button.
A list of inputs appears on the screen.
wUse the 
 
 buttons to select the desired
input, and press the 
 button.
The picture for the selected input is projected.
Basic operations
English
Français
Português Deutsch
Italiano
Español
................
..............
..............
................
...............
..........
...................
.......
.......
...................
English
French
German
Italian
Spanish
Portuguese
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Computer
Y/P
B/PR
Video
S-videoComputer
Y/P
B/PR
Video
S-video
CameraWhen a camera is
connected with the
document camera model: 
						

							27
Operations
26

Correcting the keystone distortion (Keystone)
When the foot adjuster 
p.25
 is used to change the
projection angle, the picture will undergo keystone (trap-
ezoidal) distortion.
This projector is capable of correcting this keystone distortion
.
1
Press the AUTO KEYSTONE button.The Keystone menu appears.
2
Press the AUTO KEYSTONE button again.The keystone distortion is automatically corrected. The 
 icon will appear during processing
.
Manual adjustment
Use the 
 
 buttons for keystone adjustment. When the adjustment is finished,
press the  button. The menu disappears. (The CANCEL button on the remote
control also allows you to exit the menu mode.)
KeystoneShrink button of the screen            Shrink top of the screen Item Description
Notes•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
•Keystone adjustment will not change the shape of the menus.

Zooming out the images
This equipment is provided with the digital zoom (electric zoom) (100-80%) capability in
addition to the optical zoom.
You can use the digital zoom in applications where the optical zoom is not applicable
due to some physical reasons for installations (Note, however, that digitally zoomed
display suffers from some degradation).1
Press the ZOOM – button.Each time the ZOOM – button is pressed, the
image is reduced in size.
Control panelRemote
Control
Before correction
After correction
INPUTON/
STANDBY
RESIZE
OFFCALL
AUTO
MUTE
RESIZEFREEZE SET
KEYSTONE
FA NTEMPLAMPON
VOL.
 +
VOL. -
ON / STANDBY INPUT
MENU ZOOM +ZOOM -AUTO SET AUTO
KEYSTONE
Control panelRemote
Control
FA NTEMPLAMPON
VOL.
 +
VOL. -
ON / STANDBY INPUT
MENU
AUTO SET AUTO
KEYSTONE
INPUTRESIZEMENUVO L.
+
VO L.-CANCEL
ZOOM+ZOOM-
ZOOM+ZOOM-

Using auto setting (Auto setting)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.1
Press the AUTO SET button.The Auto setting menu appears.
2
Press the AUTO SET button again.The menu item is automatically adjusted/set.
For computer input, the 
 icon will appear during
processing.
Note•Auto adjustment/setting may not be performed correctly for input signals other than
those supported by the projector 
p.46
, p.47
.
Manual adjustment and setting
The menu items vary depending on the input type, as shown in the table below.
Use the 
 
 
 
 
 buttons to adjust the items in the table below, then press
the 
 button when you are finished. The menu disappears. (The CANCEL button
on the remote control also allows you to exit the menu mode.)
PhaseAdjust with           to eliminate flicker.
Frequency
Adjust with            to eliminate periodic patterns and 
flickering when many vertical lines appear on the screen.
H-positionMove left           Move right
V-positionMove down            Move up
Clamp 1Adjusts the clamp pulse position with       or      .
Clamp 2Adjusts the clamp pulse width with       or      .
PhaseAdjust with           to eliminate flicker. Input Item
Description
Computer
Select Item Select Item
Signal format
[     : Enter to setting mode]    [          : Select one 
of the following]    [Apply:     ]
480i(525i)@60Hz/480p(525p)@60Hz/
 576i(625i)@50Hz/576p(625p)@50Hz/
 720p(750p)@60Hz/720p(750p)@50Hz/
 1080i(1125i)@60Hz/1080i(1125i)@50Hz/
 1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video mode[     : Enter to setting mode]    [          : Select one 
of the followings]    [Apply:     ]
 
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
Y/P
B/PR
Video
S-video
Note•Moving pictures generated with the DVD software for computers may appear
unnatural if it is projected with this projector, but it is not a malfunction.
Using handy features
Control panelRemote
Control
FA NTEMPLAMPON
VOL.
 +
VOL. -
ON / STANDBY INPUT
MENU
AUTO SET AUTO
KEYSTONE
INPUTON/
STANDBY
RESIZE
OFFCALL
AUTO
MUTE
RESIZEFREEZE SET
KEYSTONE
ZOOM -ZOOM + 
						

							29
Operations
28

Enlarging the picture size (Resize)
The image being projected can be enlarged.1
Press the remote control’s RESIZE 
 button.
The enlargement ratio is increased each time the RESIZE 
 button is pressed.
2
To decrease the enlargement ratio, press the remote control’s
RESIZE 
 button.
The enlargement ratio is decreased each time the RESIZE 
 button is pressed.
(The image cannot be shrunk to less than its original size.)
3
Press and hold down the 
 
 
 
 buttons to
move the enlarged area.
4
Press the CANCEL button to undo the resize.The resize is released, and the image returns to its original size.Notes•The 
 icon will appear while resize is in effect.
•An enlarged image can be frozen using the FREEZE button. The resize function on
a frozen image can also be used.
•Operations other than freeze will cancel the resize.
•Since the enlargement is performed using digital processing, enlarging will cause
the image to appear jagged.
•Rarely, the picture could become garbled while the enlarged area is being moved.
•If you use this function on video soft sold on the market, broadcast or broadcast on
cable except for the purpose of your private viewing and listening, it may infringe
the copyright protected by the copyright laws.
Remote
Control
INPUT
ZOOM +ZOOM -
CANCELRESIZE
MENUVOL.
+
VOL.-
1
24
3
Using handy features (Continued)
2
Press the ZOOM + button to bring it back to the original size.Each time the ZOOM + button is pressed, the image size increases.
(You cannot make it larger than the original size.)Notes•Pressing either the ZOOM- or ZOOM+ button would display the 
 icon.
•The adjustment value will automatically be saved.

Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.The picture and sound are cut off. The Mute function is released
when pressing the MUTE button again. To cancel the command,
press the CANCEL button.Notes•The 
 icon will appear while mute is in effect.
•Operating any other functions cancel the muting.

Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture pauses. The Freeze function is released when pressing
the FREEZE button again. To cancel the command, press the
CANCEL button.Notes•The 
 icon will appear while freeze is in effect.
•The freeze function can be used on the resize function. Other operations will
release the freeze.
•Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
•If you use this function on video soft sold on the market, broadcast or broadcast on
cable except for the purpose of your private viewing and listening, it may infringe
the copyright protected by the copyright laws.
Remote
Control
INPUTON/
STANDBY
RESIZE
OFFCALL
AUTO
MUTE
RESIZEFREEZE SET
KEYSTONERemote
Control
INPUTON/
STANDBY
RESIZE
OFFCALL
AUTO
MUTE
RESIZEFREEZE SET
KEYSTONE 
						

							31
Operations
30
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons 
p.16
 on the control panel (main unit side) and remote control.

How to use the menus
The menu shown below is only for operation instructions and might be different from the
actual display.
Using the menus
Note
•Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
•You can also use the CANCEL button on the remote control to dismiss the menu display.
Display the Setting display menu
To  Status display
The menu disappears.
1. Start
2. Select a Category
3. Adjustments & Settings
4. Back6. End 5. To  Finish
Finish via the Status 
display menu.
Select a category by using  
         .
There are following three 
categorys.Displays the current 
adjustments of selected 
category.
Item shown with gray 
cannot be adjusted with 
the current input source.
p.32
Image adjustment menu
p.32
Default setting menu
p.30
Display setting menu
p.33
The figure shows a typical example.  
As the display may differ depending 
on the item, use the following pages 
as a reference.
Item
Adjustment/Setting Value
This mark signfy that 
there are options.
Press        to display a 
list of options.
These marks signify the 
items can be adjusted/set 
by using                .
These marks signify an 
item can be switched by 
using                .
These marks signify the items can be selected from 
the list by using            .
After an item is selected, apply it by pressing      .
Press      to open the menu 
of the selected category.

Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
 button twice (or press the CALL button on the remote
control once).
When the 
 button is pressed once, the Setting
display menu appears. Pressing it again displays
information p.31
. The table below shows what kind
of information is displayed. Press the 
 button (or
press the CALL or CANCEL button on the remote
control to serve the same purpose) again to
dismiss the display.
“Ye s”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video
CameraS-video
Input Input source name Yes Yes Yes YesRGB signal mode RGB input mode 
[Note 1]
YesNoNoNo
H-resolution Horizontal resolution (in bits) Yes No No NoV-resolution Vertical resolution (in bits) Yes No No NoH-frequency Horizontal sync frequency Yes No No NoV-frequency Vertical sync frequency 
[Note 2]
YesNoNoNo
Sync Sync signal polarity 
[Note 3]
YesNoNoNo
Signal format Y/P
B/PR signal format No Yes No No
Video mode Color method of video signal No No Yes NoLamp time Time of lamp use 
[Note 4]
Ye s Ye s Ye s Ye s
Version Firmware version 
[Note 5]
Ye s Ye s Ye s Ye s
Notes
1: The mode of supported RGB signals 
p.46
 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 3,000
hours, consult with a store about getting a TLPLV2 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
Notes•The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
•Conducting another operation while information is being displayed dismisses the
display.
Control panelRemote
Control
INPUTON/
STANDBY
RESIZE
OFFCALL
AUTO
MUTE
RESIZEFREEZE SET
KEYSTONE
FA NTEMPLAMPON
VOL.
 +
VOL. -
ON / STANDBY INPUT
MENU ZOOM +ZOOM -AUTO SET AUTO
KEYSTONE
Using handy features (Continued) 
						

							33
Operations
32

The display setting menuUse this menu to set screen display-related items.
(Full):  Display with LCD panel’s resolution
(Thru): Display with sampling resolution (for computer input)
(Wide):  Wide-screen display (for Video, S-video, and Y/P
B/PR)
Select one of the languages below to use for displaying menus and messages[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/
Português/            /                      /                      /Screen to display when there is no input signal                        
 (Logo)                            (Blue)                            (None)
Display icons as function guidesOn Off
Display start-up screen when power turned on On Off Description
Item
Screen size
Language
Background
Icon
Start-up screenNotes
•If “Thru” is selected for screen size, portions exceeding the pixel count of the LCD panelp.45
 will not appear on the screen. Note that for RGB signals with clock speeds
SXGA3_60 
p.46
 or lower, all input pixel signals are sampled. (This effect is noticeable
when the screen is enlarged using the Resize function 
p.29
). However, if the clock speed
is higher than this, the RGB pixel signal is reduced before sampling.
•Displaying the images with the aspect ratio different from the original with the purpose of
other than the personal and private viewing, using the screen size menu may violate the
copyright protected by the law.

Reset menu (Special menu)When other menus are not displayed and the 
 button is held down, the menu appears.
•When the screen is placed vertically, and Auto keystone correction is executed, but the
keystone correction is not successful, stow the foot adjuster in its original position, place
the projector on a flat surface, select Horizontal reference value reset, and press the 
button.
•Select Reset All and press the 
 button to return all menu items to the factory settings.
Reset the horizontal reference value for Auto keystone correction[     : Enter execution mode]     [Ye s           No]     [Apply:     ]
Reset all menu items to their factory settings
[     : Enter execution mode]     [Ye s           No]     [Apply:     ] Description Item
Horizontal reference 
value resetReset all
Using the menu (Continued)
The image adjustment menuUse this menu to adjust image-related items.Items that can be adjusted are marked with  “Ye s”, and those that cannot are marked with “No”.
Item    
  
Description
Computer
Y/P
B/PR
Video S-video
Camera
 
Contrast
Lower
Higher
Yes Yes Yes Yes Yes
Brightness
Darker
Brighter
Yes Yes Yes Yes Yes
Color
Lighter
Deeper
N o Ye s Ye s Ye s N o
Tint 
[Note 1]
Reddish
Greenish
No No Yes Yes No
Sharpness
Softer
Sharper
N o Ye s Ye s Ye s Ye s
R-level
Less red
More red
Yes Yes Yes Yes Yes
G-level
Less green
More green
Yes Yes Yes Yes Yes
B-level
Less blue
More blue
Yes Yes Yes Yes Yes
Up/down shift 
[Note 2]
Shift down
Shift up
N o Ye s Ye s Ye s N o
Notes
1:Tint can only be adjusted when Video mode  is set to NTSC or NTSC4.43.
2:Up/down shift can only be adjusted when Screen size 
p.33
 is set Wide.

The default setting menuThis menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style  Sets the period of time to wait until turning off the power after signal input stops: Off (not turned off)          1 min           2 min           ...          60 minSets whether to turn on the power when the ON/STANDBY button is pressed 
(Manual), or when the power cord is plugged in (Auto).   Manual             AutoSets the lamp power                                    Standard           LowSets the camera’s shutter speed to either (50Hz) or (60Hz).
 50Hz            60Hz.
Sets the camera’s white balance to (Auto) or (Fixed).
 Auto            Fixed. Description
Item
Projection
mode
No signal 
power off
Power on
Lamp power 
[Note 1]
Shutter speed
White balance
 [Note 2]
(Back hung 
from ceiling) (Placed 
on floor)(Rear)(Hung from 
ceiling)
p.19
Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
“Standard” when the power is turned on next time.
2: White balance, if set to Fixed, is reset upon power off and the Auto is resumed the next time the
unit is turned on. (Models with the document camera)
Notes
•Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
•Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp. 
						

							35
Operations
34


Preparation of the document camera (when loading the camera)PRECAUTIONS
•Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
•Note that when extending or rotating the camera arm, the arm moves in an arc. Take care
not to bump yourself or others with it.
Preparing the document camera (for use being separated
from the projector)
•Before connecting the camera cable, make sure that the projector power is off.PRECAUTIONS
•Insert a camera cable straight and securely until it locks. When disconnecting the cable,
pull it out releasing the lock on both sides of the plug.
•Be sure to pull the tip resistant bar fully until it forms the angle of 90 degree. If you don’t
use the bar, the camera may topple over.
•Note that the camera may tip over if you attempt to rotate the arm in the opposite side of
the tip resistant bar.
•For camera interconnection, be sure to use the supplied camera cable (1 m). If you use
the other cables, the normal operation cannot be achieved and even the malfunction may
result.
Note
•Connecting or disconnecting the camera cable with the projectors power ON may cause
camera error (
 is displayed) and even turn off the power.
Status before preparation
(When stowed)1) Set up arm 2) Extend arm
3) Rotate arm 4) Raise camera head
1) Connect the supplied
camera cable to the
camera input terminal.2) Connect the other end of
the camera cable to the
camera terminal on the
document camera.3)
Pull out the tip resistant bar
and set up the document
camera
.
Using the document cameraPlease read this chapter if the model you purchased includes a document camera.
Uninstalling the camera
Installing the camera
PRECAUTIONS
•Before mounting or dismounting the document camera, disconnect the power plug.
•Place a soft cloth beneath the projector when mounting or dismounting the camera.
•Do not dismount or mount the document camera while the projector is upright or kept in the air
.
•Before mounting the camera, confirm that the interconnection connector is closed with
the connect lever. If you attempt to mount the camera with the connector being protruded,
connector may be damaged.
•When mounting the camera, be sure to slide the document camera until it is locked with
click sound.
•Confirm the four registration stays are aligned before sliding the camera.
1)Place the folded document
camera with the bottom
side up.
2) Slide the connect lever in
the direction of an arrow.3) Pressing the lock lever in
the direction of an arrow,
slide the document
camera.
1)
Place the folded document
camera with the bottom
side up.
2) Align the four registration
marks.3) Slide the document
camera in the direction of
an arrow until it clicks.
4) Slide the connect lever in
the direction of an arrow. 
						

							37
Operations
36
5
Adjust the focus using the focus ring on the camera headRotate the focus ring to either NEAR or FAR, whichever is better in focusing.
6
If the screen is too dark or too bright, use the
CAMERA GAIN (+/–) buttons to make it easier to see.The Sharpness of the camera image can also be adjusted using
the Image adjustment menu 
p.32
.
7
After use, turn off the light, and fold up the document camera.Fold up the camera using the opposite order from Preparation of the document camera
.
PRECAUTION
•If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent
light, or set the Shutter speed from the Default menu 
p.32
. Note that changing the
Shutter speed setting may not eliminate the flicker, depending on the lighting, state of
the document, or image adjustment.
Note
•No audio is output when camera input is selected.
Turn the focusing ring to adjust
the focus.
•Near: 100 mm to 300 mm
Far: 300 mm to 5 m
Using the document camera (Continued)
Image projection with the document camera1
Place the document.Set the document at the top of or the side of the projector
.
2
Press the CAMERA button, and select camera input.•The input returns to the previous input when the CAMERA
button is pressed again.
•Camera input can also be selected by pressing the remote
control or camera’s INPUT button.3
Rotate the camera lens to align the orientation of the document for
shooting.
4
Move the camera head up and down to adjust the image size.•Closeup shot with the distance shorter than 100 mm cannot be performed.
Farther: Smaller image
Closer: Larger image 
						

							38
39
Maintenance

Locking the white balance
Although the projector’s camera is constantly adjusting the color balance of the images
it photographs, the color balance may be disrupted, depending on the color layout of
the document, etc. If this happens, the white balance can be locked using the proce-
dures below.
1
Lay down a piece of white paper, and adjust so it fills the screen.Adjust the camera head and arm so that the white paper fills
the screen completely.
2
Set the White balance to Lock in the
Default menu. 
p.32
The white balance is locked. If you want to return to the auto adjustment, set the White
balance to Auto in the Default menu.Notes
•White balance setting to Fixed, if power is turned off, will be back to Auto.
•The color of the room lighting may prevent the white balance from being adjusted to the
optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level,
G-level and B-level on the Image adjustment menu 
p.32
.
Using the document camera (Continued)
The air filter prevents dust and debris from getting inside the projector. Never run the
projector with the filter removed. It is recommended that the air filter is cleaned regularly.
•The icon message 
 “Check the air filter for dirt.” is displayed every 100 hours. (If the
usage time exceeds 100 hours, this message is displayed for 30 seconds when the image is
displayed for the first time after power is turned on. This display will be dismissed with any
operation.)
•Check out the filter and any debris is found, use the following procedure for cleaning.
 WARNING
•Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.1
Unplug power cord.
2
Remove the air filter.Pull out the air filter by taking the catch shown in the figure.
3
Clean the filter.Carefully remove the dust and dirt from the air filter with a
vacuum cleaner or the like.
4
Replace the air filter.Notes
•Allowing dirt and dust to build up in the air filter will worsen the air circulation inside the
projector, causing the internal temperature to rise, causing the projector to stop working
or malfunction.
•Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the
projector again.
•If you wash the air filer with water, make sure to dry it completely before replacing it.
•If the air filter is torn, consult with your dealer about replacing it with a new one.
Continuing to use a ripped filter will allow dust and dirt to get inside the projector.Air filter cleaningMaintenance