Toshiba Projector Tlp 790 User Manual

11
Before use
CONTENTSNames of each part on the main unit
Continued
16
12Control panel
Infrared remote sensor
Air exhaustCAUTION LabelSpeaker
SERIAL NO. Label RATING Label WARNING Label
Lens cover
LensFocusing ring
31
Zooming lever31
Air intake
Air intakeAir intake
Foot adjuster
20
Lamp cover66
Foot adjuster release button20
AC IN socket19
Carrying handle
Open to carry 
the projector.
Anti-theft 
lock hole
CAUTION Label WARNING Label
CAUTION
Openings in the cabinet are provided for ventilation and to...

12
Before use
CONTENTSNames of each part on the main unit (continued)
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
TEMP indicator
KEYSTONE button
To correct the keystone distortion of
the picture.
FA N indicator LAMP indicator ON indicator
INPUT button ENTER button  Selection buttons EXIT button
VOL/ADJ buttons 
AUTO SET button  MENU buttonON/STANDBY button
Top side
Control panel
To set and/or adjust values on the menu.
To adjust the volume when the menu is not displayed.To...

13
Before use
CONTENTS
USBCOMPUTER IN 1COMPUTER IN 2
S-VIDEO VIDEOVIDEO INR - AUDIO - LAUDIO
IN
(
Y/PB/PR )MONITOR
OUT
CONTROL
2673CONTROL connector
(RS-232C connector)
To connect a computer to control the
projector. (Remove the cover to use
the connector.)
42USB connector
To connect to a USB connector of a
computer when using the remote control 
mouse.
2225AUDIO IN jack (Audio input)
(ø 3.5mm stereo mini-jack)
To enter audio signal from a computer or video
equipment with component video output (Y/P...

14
Before use
CONTENTSNames of each part on the remote control
INPUT button
MUTE button RESIZE buttons R-CLICK button
L-CLICK button Pointer control button
VOLUME/ADJUST buttons KEYSTONE button
AUTO SE T button LASER button
PIP button
FREEZE button
CALL buttonON/STANDBY button Laser emission part
Remote control transmission partTo display the laser pointer by pointing the laser
emission part toward the screen.
To set and/or adjust values on the menu.
To adjust volume when the menu is not displayed....

15
Before use
CONTENTSLoading batteries
Notes
Using batteries incorrectly can cause them to leak
or burst. Strictly observe the following.
•Install the batteries with their + and – ends facing
correctly.
•Do not charge, heat, disassemble, or short the
batteries or throw them into a fire.
•Do not leave any exhausted batteries in the
remote control.
•Do not mix different types of batteries or new and
old batteries.
•When you will not be using the remote control for
a prolonged period, take the batteries...

16
Before use
CONTENTSRemote control operation
Point the remote control at the infrared remote sensor and press a button.
Notes
•The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the projector’s remote sensor.
•Operate the remote control from a position where the remote sensor is visible.
•Do not drop the remote control or otherwise jolt it.
•Keep the remote control out of locations with excessively high temperature or humidity.
•Do not...

Installation and
connections
CONTENTS17Floor-mounted projector placement
Floor-mounted front projection
Viewing a picture projected on the front of the
screen from a floor installation.
Floor-mounted rear projection
Viewing a picture projected through the back of the
screen from a floor installation.
Viewer Translucent screen
Viewer There are two ways to place the floor-mounted projector. Perform the “Projection mode” setting on the menu screen for the projection
method. 
51
For the ceiling-mounted...

Installation and
connections
CONTENTS18
Place the projector on a steady, level surface such as a table.
To obtain proper screen projection, place the projector so that the light beam hits the screen squarely.
Floor-mounted projector placement (continued)
Top view
Screen
Screen
90°
B C
Side view
90°
Screen
1
2
90°
Point the lens straight at the center of the screen as above.
Determine the screen size projected on the screen.
The projection size depends on the distance between the lens and the screen....

Installation and
connections
CONTENTS19
Connect the power cord.
• Insert one end into the AC IN socket on the projector.
• Insert the other end into a wall outlet.
Notes
•When the projector is moved from a cold location to a warm location, or when the ambient temperature in the projection room has risen suddenly,
moisture may condense on the lens or the internal optical section to blur the projected pictures. In such a case, leave the projector for an adequate time
(1 to 2 hours, depending on the room’s...

Installation and
connections
CONTENTS20Projector placement angle adjustment
Foot adjuster
release buttonFoot adjuster The tilt of the projector can be adjusted using the foot adjuster.
Lift the front of the projector until the desired tilt angle is
obtained and hold down the foot adjuster release button.
The foot adjuster will extend.
Release the button to lock in position.
1
Turn the foot adjuster to make fine adjustment to the
height.
Turn clockwise to lift up.
Turn counterclockwise to lower.
2
Notes...