Toshiba Projector Tlp 780U User Manual

							41
Operations
CALL
CALL
CALL
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE
RESIZE
VOLUME/ADJUSTLASER
Status display
Input - current input source
H-resolution - the horizontal resolution of the input signal (at RGB input)
V-resolution - the vertical resolution of the input signal (at RGB input)
H-frequency - the horizontal frequency of the input signal (at RGB input)
V-frequency - the vertical frequency of the input signal (at RGB input)
Sync - the polarity of the sync signal (at RGB input)
Video mode - the color mode of the video signal (at Video, S-Video input)
Signal format - the formatting of the Y/P
B/PR signal (at Y/P
B/PR input)
Lamp time - the elapsed using time of the lamp
Version - the version of the firmware
Shutter - the shutter speed of the document imaging camera (at document
imaging camera input)
Displaying Information
Information on the input signal source, etc., can be displayed.
Press CALL.The information described below is displayed.
The information display turns off when the CALL button is
pressed again.
• The information displayed is not refreshed even if it changes. To refresh the information,
turn off the information display, then turn it back on.
• The information display turns off if any other operation is performed.
• The Lamp time shows an approximate time for lamp replacement. (It should not be used
as a lamp warranty time counter.) If the time indicated here nears 1000, contact your store of
purchase about obtaining a replacement lamp (TLPL78, sold separately).
• The Lamp time can be reset when the lamp is replaced.
• The Version is the version of the control program used in the projector and is used for
servicing, etc. Remote controlNotes 
						

							42
Operations
MENUON/STANDBY INPUT
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUSTLASER
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUSTLASER
USB
COMPUTER IN 1
COMPUTER IN 2
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN(
Y/PB/PR )
MONITOR
OUTCONTROL
Operating a computer by the remote control
You can control a computer by the remote control when the projector and computer are connected with the supplied USB cable.
In this manual, this function is explained as mouse remote control.
To USB connector
Be sure to connect in the
proper direction.USB cable (supplied)
To USB port Remote control
Pointer control
R-CLICK
L-CLICK
Point the remote control at the remote control
sensor on the projector when operating with its
buttons.•To move the pointer Press the outer side of the
pointer control button in the direction in which
you want to move the pointer.  (The speed at
which the pointer moves depends on how
strongly the button is pressed.)•To click
Press L-CLICK or the center of the pointer
control.•To right-click
Press R-CLICK.•To drag and drop
While holding down the center of the pointer
control, press the rim side to move the pointer to
the desired spot, then release the center part.
Computer
• This function is available with Windows98 and Mac OS9 computers equipped with a USB port as standard.
• When connecting the computers USB port for the first time, a message asking you to insert the Windows98 CD-ROM may appear on the computers
monitor screen, depending on whether or not the device driver is installed.  If so, do as the message says.
• When using a USB cable other than the supplied one, be sure to use a shielded type.
Notes 
						

							43
Adjustments &
Settings
MENU MENU
End
Press MENU.Then GUIDE MENU appears, and a list of several 
items is displayed in the menu.
MENU MENU
When you make more 
detailed adjustments 
and settings, call the 
FULL MENU.Return to the GUIDE MENU when 
the MENU button is pressed.
Press MENU button once again.The FULL MENU of [Picture] appears.
FULL MENU has seven pages of [Picture], [Position], [Color], [Audio], 
[Display], [Default setting] and [Reset].
Use the selection button (        ) to change the page of FULL MENU.
/
[Picture]
[Position]
[Color]
[Default setting]
[Reset]
[Display]
[Audio]
Select the item with the selection 
button (         ). 
/
ENTER ENTER
Press ENTER to decide.The item selected can be adjusted or set.
EXIT EXIT
Press EXIT and return.When you select other items, press EXIT repeatedly 
until GUIDE MENU appears.
When you want to quit, press EXIT repeatedly until 
GUIDE MENU disappears.
Start
FULL MENU: For the operating instruction, refer to the next page.  GUIDE MENU: 
You can adjust or set the functions used frequently.Items
Button operation guide The current input source
Adjust and set it with the button indicated 
on the button operation guide.According to the selected item, the kind ([adjustment],[setting] 
or [execution]) and the button to be used are indicated on the 
button operation guide.
VOL/ADJ
Selection
MENU
ENTEREXIT
MENU ENTER
EXIT
PIP
FREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
KEYSTONE
AUTOSET
EXIT
ON / STANDBYVOL / ADJ
ENTER
MENU
INPUT
FAN
TEMP
LAMP
ONVOL/ADJSelection
MENUENTEREXIT
Control panel (Main unit side)
Remote control
44
Operating the menu screen
Various adjustments and settings can be made on the menu screen.  The basic operation on the menu screen is shown here. 
						

							44
Adjustments &
Settings
End
Select the item with selection buttons (          ).State of a figure below is a sample for explanation. 
This state does not in fact.
/
ENTER ENTER
Press ENTER.The Item selected is executed.  FULL 
MENU is displayed after execution.
ENTER ENTER
Press ENTER.An object can be selected from the 
sub menu list.
Start
VOL/ADJSelection
MENU
ENTEREXIT
MENU ENTER
EXIT
PIP
FREEZEMUTE CALLRESIZE
VOLUME/ADJUST
KEYSTONE
AUTOSET
EXIT
ON / STANDBYVOL / ADJ
ENTER
MENU
INPUT
FANTEMP
LAMPONVOL/ADJSelection
MENUENTEREXIT
Control panel (Main unit side)
Remote control
Adjustment display bar
Setting objects
Kind (page) of FULL MENU
Select it with the button indicated 
on the button operation guide.
For the selection method of FULL MENU, refer to 
the previous page.
ENTER ENTER
Press ENTER.Only the (small list of the) selected 
adjusting items is displayed.
This is useful as you can see a main 
picture not hidden under FULL MENU.
Adjust with VOL/ADJ (+/-) or 
selection buttons (         ).
/
EXIT EXIT
Press EXIT.FULL MENU is displayed and you can 
select other items.
EXIT EXIT
Press EXIT.FULL MENU disappears, and 
adjustment or setting is finished.
At the item where the
adjustment bar is displayed;At the item where the 
setting objects are 
displayed on sub menu;
Method -1
Method -2
Adjust with VOL/ADJ (+/-)Press the selection button (         ) when selecting othe items continuously.
/
At the item where [Execution] is 
displayed on the operation guide;
Items
Button operation guide The current input sourceOperating the menu screen (continued)
43
• An exclusive menu is displayed when making PIP function sub-picture settings.
53
Note 
						

							45
Adjustments &
Settings
Adjust the image brightness.
ContrastBrightness
Adjusting contrast of the pictureAdjusting brightness of the picture
ADJ.ADJ.
Adjust the image flicker.
Phase
Adjusting flicker of the picture (sampling clock phase adjustment)
ADJ.
Select the image with its brightness 
priority or quality (color) priority.
Bright
Priority is given to brighter picture
SET
True color
Priority is given to the true color of the picture
SET
Correct the keystone distortion 
of the screen.
Auto. V-keystone
The vertical keystone distortion is adjusted automatically: COMPUTER IN 1 connector is selectable by INPUT button: COMPUTER IN 2 connector is selectable by INPUT button
EXEC.
VIDEO
: Video input is selectable by INPUT button
SETEXEC.
To manual adjustment
Adjusting the Vertical keystone
ADJ.
V-keystone
Adjusting the Horizontal keystone
ADJ.
H-keystone
Select the input source when 
changing the input.
SET
COMPUTER IN 1
: Use COMPUTER IN 1
 connector
 as Analog RGB(1) input
SET
Analog RGB(1)
: Use COMPUTER IN 1
 connector
 as Y/P
B/PR input
SET
Y/P
B/PR
SET
COMPUTER IN 2
: Use COMPUTER IN 2
 connector
 as Analog RGB(2) input
SET
Analog RGB(2)
: Use COMPUTER IN 2
 connector
 as Digital RGB input
SET
Digital RGBS-VIDEO
: S-Video input is selectable by INPUT button
SET
CAMERA
: Camera input is selectable by INPUT button
SET
Ye s Ye s Ye s
Adjust the image color.
Color
Adjusting color deepness of the picture
ADJ.
Adjust the gain of the document imaging camera.Reduce the flicker.
Camera gain
Adjusting the document imaging cameras gain
ADJ.
Ye s
---- --
---- --Yes
----
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
Select it from follows so that flickering of the document imaging cameras picture decreases
Shutter
The shutter speed is set automatically
SET
Auto
The shutter speed is fixed to 50 Hz
SET
50Hz
The shutter speed is fixed to 60 Hz
SET
60Hz
Ye s Ye s Ye s Ye s Ye s Ye s Ye s
--- -Ye s Ye s Ye s---- Yes Yes -
: On/Off with ENTER: On/Off with (+) or (-)
GUIDE MENU adjustments and settings
On GUIDE MENU, you can set or adjust the functions frequently used.
To operate GUIDE MENU, refer to page       .• The items related to the camera (the document imaging camera) are displayed only with a model having the camera.
• Sampling phase is to be adjusted and memorized for each RGB signal         .
• Keystone and Input source setting can be adjusted (set) at all input sources, but the adjustments (settings) made at one input source are applied
to all input sources.
• It is impossible to exit from the menu if no input source is selected.
• If the check in the check box for the currently selected source is removed, the setting becomes effective the next time the input is changed.
• The adjustments or settings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord
is unplugged or if a power failure occurs while the projector is on, the adjustments or settings are not memorized.
43
71
Notes 
						

							46
Adjustments &
Settings
Contrast
Brightness
Adjusting contrast of the pictureAdjusting brightness of the picture
ADJ.ADJ.
Sharpness
Adjusting sharpness of the picture (This item is setting instead of adjustment at Y/P
B/PR input.)
ADJ.
Picture mode
Bright
Priority is given to brighter picture
SET
True color
Priority is given to the true color of the picture
SET
Camera gain
Adjusting the document imaging cameras gain
ADJ.
---- --
Overlay gain
Adjusting the level of the overwriting picture using the document imaging camera
ADJ.
Reset 
The adjustments and settings of FULL MENU [Picture] are returned to the factory default setting
EXEC.
----
Video mode
Auto
The video mode (color system) is set automatically
SET
NTSC
The video mode is fixed to NTSC system
SET
PA L
The video mode is fixed to
 PAL system
SET
SECAM
The video mode is fixed to
 SECAM system
SET
PAL-N
The video mode is fixed to
 PAL-N system
SET
PAL-M
The video mode is fixed to
 PAL-M system
SET
PAL-60
The video mode is fixed to
 PAL-60 system
SET
NTSC-4.43
The video mode is fixed to
 NTSC-4.43 system
SET
Signal format
Auto
The Y/P
B/PR signal format is set automatically
SET
525i
The Y/P
B/PR signal format is fixed to 525i mode
SET
525p
The Y/P
B/PR signal format is fixed to 525p mode
SET
625i
The Y/P
B/PR signal format is fixed to 625i mode
SET
750p
The Y/P
B/PR signal format is fixed to 750p mode
SET
1125i
The Y/P
B/PR signal format is fixed to 1125i mode
SET
Shutter
Auto
The 
shutter speed
 is set automatically
SET
50Hz
The 
shutter speed
 is fixed
 to 50 Hz
SET
60Hz
The 
shutter speed
 is fixed
 to 60 Hz
SET
--- -
Screen size
Full
The picture is converted to XGA (1024 x 768 dot) resolution
SET
thru
The picture is displayed with the input resolution
SET
Wide
The picture is converted to the wide screen picture
SET
Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
Ye s Ye s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye s Ye s
Ye s
- --- ---Ye s
Ye s Ye s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye s Ye s Ye s Ye s Ye s---- --Ye s ---Ye s Ye s Ye s
---- -Ye s Ye sYe s
Ye s Ye s Ye s
FULL MENU adjustments and settings - Picture
You can adjust various items of the picture from FULL MENU [Picture].
To operate FULL MENU, refer to page         .
44
• The items related to the camera are indicated only with a model having the camera.
• A part of function is restricted if the object other than [Auto] is selected in Video mode or Signal format.
• The adjustments or settings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord
is unplugged or if a power failure occurs while the projector is on, the adjustments or settings are not memorized.
51
Notes 
						

							47
Adjustments &
Settings
H-position
V-position
Adjusting the horizontal display position of the pictureAdjusting the vertical display position of the picture
ADJ.ADJ.
Phase
Adjusting flicker of the picture  (sampling clock phase adjustment)
ADJ.
Frequency
Adjusting the sampling frequency of the input signal
ADJ.
Reset
The adjustments of FULL MENU [Position] are returned to the factory default value
EXEC.
---- Yes Yes ----- Yes Yes ----- Yes Yes ----- Yes Yes ----- Yes Yes -
Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
FULL MENU adjustments - Position
• This menu is not displayed except analog RGB input.
• The adjustment of each item in this menu is memorized for each RGB signal input          .
• The adjustments made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord is
unplugged or if a power failure occurs while the projector is on, the adjustments are not  memorized.You can adjust the picture position etc. of analog RGB input from FULL MENU [Position].
To operate FULL MENU, refer to page         .
44
71
Notes 
						

							48
Adjustments &
Settings
Color
Tint
Adjusting color deepness of the pictureAdjusting tint of the picture  (not adjustable at PAL, SECAM, PAL-N,PAL-M and PAL60)
ADJ.ADJ.
R-level
Adjusting reds color level of the picture
ADJ.
G-level
Adjusting greens color level of the picture
ADJ.
B-level
Adjusting blues color level of the picture
ADJ.
Reset
The adjustments of FULL MENU [Color] are returned to the factory default value
EXEC.
Ye s Ye s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye s Ye sYe s Ye s Ye s Ye s Ye s Ye s Ye s
---- YesYes--Yes-- YesYes-
Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
FULL MENU adjustments - Color
• The adjustments made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord is
unplugged or if a power failure occurs while the projector is on, the adjustments are not memorized.You can adjust the color condition of the picture from FULL MENU [Color].
To operate FULL MENU, refer to page         .
44
Notes 
						

							49
Adjustments &
Settings
Volume
Adjusting the sound volume developed from speaker
ADJ.
Speaker output
On
The sound is developed from the speakers
SET
Off
No sound is developed from the speakers
SET
Reset
The adjustments and settings of FULL MENU [Audio] are returned to the factory default setting
EXEC.
-- -
Loudness
On
The loudness effect is added to the speaker sound
SET
Off
The loudness effect is not added to the speaker sound
SET
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
Ye s
 (common)
-
Channel select
L+R
The sound of the left and right channels is mixed and developed from the speaker
SET
L
Only the sound of the left input channel is developed from the speaker
SET
R
Only the sound of the right channel is developed from the speaker
SET
Ye s Ye s Ye s Ye s Ye s Ye s -
Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
FULL MENU adjustments and settings - Audio
• When the camera input is selected, the sound is not developed.
•Each item can be set at every input sources except the camera input, but the settings made at one input source are applied to all input sources as shown
in the table.  The sound volume can be adjusted for each input source except the camera input.• The adjustments or settings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord
is unplugged or if a power failure occurs while the projector is on, the adjustments or settings are not memorized.You can set the sound developed from the speaker from FULL MENU [Audio].
To operate FULL MENU, refer to page         .
44
Notes 
						

							50
Adjustments &
Settings
V-keystone
Adjusting the keystone distortion when having changed the vertical installation angle
ADJ.
Language
English
The language is set to English for menu and message displayed
SET
Français
The language is set to French for menu and message displayed
SET
Icon
OnOff
Reset
The adjustments and settings of FULL MENU [Display] are returned to the factory default setting
EXEC.
Português
The language is set to Portuguese for menu and message displayed
SET
The language is set to Japanese for menu and message displayed
SET
H-keystone
Adjusting the keystone distortion when having changed the horizontal installation angle
ADJ.
Deutsch
The language is set to German for menu and message displayed
SET
Italiano
The language is set to Italian for menu and message displayed
SET
Español
The language is set to Spanish for menu and message displayed
SET
The language is set to Chinese (Simplified) for menu and message displayed
SET
The language is set to Chinese (Traditional) for menu and message displayed
SET
The language is set to Korean for menu and message displayed
SET
The icon is displayed
SET
The icon is not displayed
SET
Menu translucent
OnOff
The menu background becomes translucent
SET
The menu background in normal state
SET
Menu position
Upper leftUpper right
The menu is displayed to upper left on the screen
SET
The menu is displayed to upper right on the screen
SET
Bottom left
The menu is displayed to bottom left on the screen
SET
Bottom right
The menu is displayed to bottom right on the screen
SET
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)
Ye s
 (common for all of the inputs)Digital RGB
Y/P
B/PR
Video
The relationship between input source and item      Yes: Adjustable   -: Not displayed
S-Video Camera
Analog RGB(1) Analog RGB(2)
FULL MENU adjustments and settings - Display
• Each item can be set at all input sources, but the settings made at one input source are applied to all input sources.
• The adjustments or settings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button.  If the power cord
is unplugged or if a power failure occurs while the projector is on, the adjustments or settings are not memorized.You can set the language, menu display, etc. from FULL MENU [Display].
To operate FULL MENU, refer to page         .
44
Notes