Toshiba Projector Tlp 670U User Manual

CONTENTS11Before use
ON/STANDBY MENU ENTERSELECT/ADJUST
INPUTON
LAMP
TEMP
Part names and functions
Main unit
Lens cover
Exhaust holes
Foot adjuster
release button 
20
Foot adjuster 20
Projection lensZooming ring 
21
Focusing ring 21
Infrared remote sensor Intake holes
ON/STANDBY button 21
To turn the projector on or off.
MENU button 27
To display or close the menu.
SELECT/ADJUST button 28
(  /  /  /  )
To select items or adjust values on the
menu.
ENTER button 30
To enter your selection on the menu....

CONTENTS12Before use
(Continued)
Left sideRight side
AC IN socket 19Carrying handle
Open to carry the projetor.
Rear sideCONTROL connector 17 49
To connect a computer to control the projector.
MONITOR OUTPUT connectors
(RGB output, AUDIO output) 
17
To connect to a monitor or audio equipment.
RGB INPUT connectors (RGB input, AUDIO input) 16
To connect a computer, etc.
VIDEO INPUT connectors
(S-VIDEO input, VIDEO input, AUDIO input) 
17
To connect a video equipment, etc.
(Continued)
Document imaging...

CONTENTS13Before use
AUTO SET
POINTERPJ
MARKERLASER
MENU ENTER
KEYSTONEON/STANDBY
R-CLICK L-CLICK
VIDEO CAMERA RGB
RESET
MUTE CALLFREEZE RESIZE
(Continued)
Remote control
* Functions when the POINTER/PJ selector is
set to “POINTER”.
AUTO SET button 23
To adjust the image automaticcally.
KEYSTONE button 22
To correct the keystone distortion of the
picture automatically.
MARKER button
To display a marker on the screen.
Each time the button is pressed, the
marker changes the shape, and finally
disappears....

CONTENTS14Before use
(Continued)
Installing batteries
1) Open the cover.
2) Install the batteries.
Make sure that the +/Ð polarities match the
illustration in the compartment.
3) Attach the cover.
(Continued)
L-CLICK button* 26 / MENU button 28
¥ To left-click.*
¥ To display or close the menu.
RGB button 21
To select the RGB input.
RESIZE button 24
To change the picture size.
ON/STANDBY button 21
To turn the projector on or off.
LASER button
To display the laser pointer by pointing the
laser emission...

CONTENTS15Before use
Remote control operation
Point the remote control at the infrared
remote sensor and press a button.
Distance : within about 5 meters from the front
of the remote sensor.
Angle : within about 15° of the remote
sensor in every direction.
Notes
•Do not leave the remote control unit turned
the  face down as it may make the buttons
pressed to hasten the battery end.
•The remote control may not operate when
there is sunlight or other strong light such as
a fluorescent lamp shining on the...

CONTENTS16Connections and installation
Connections
Connecting an IBM PC or compatible computer (DOS/V)
Check that the power for the projector and computer is off before
connecting the cables.
Notes
¥ The projector cannot be connected to a computer that does not have
an analog RGB output terminal. For details, refer to the computer
manual.
¥ You may not be able to connect some computers to the projector. For
details, consult the dealer.
¥ If NTSC/PAL/SECAM signals are input to the RGB INPUT connector,...

CONTENTS17Connections and installation
RS-232C
CONTROLRGB AUDIO
MONITOR OUTPUTRGB
S-VIDEO VIDEO VIDEO INPUT
L - AUDIO -RAUDIO
RGB INPUT
To MONITOR OUTPUT (AUDIO) 
Ø3.5mm STEREO mini plug
(Audio output level is constant.)
To audio input Audio cable
(not supplied)
Connect a stereo system
for dynamic sound.You can connect an 
extra monitor to view 
the picture.
You can connect a computer 
to control the projector.
49
(Continued)
Connecting video equipment
Check that the power for the projector and computer...

CONTENTS18Connections and installation
Projector placement
There are four ways of installing this projector
as shown right. This section explains the
standard case of the floor-mounted front
projection.
CAUTION
¥ When a ceiling mount is required, please
consult with the dealer.
¥ When carrying the unit, always handle the
carrying handle.
Preparation
¥ Select a room that can be darkened.
¥ Refer to the table on the next page 
19 for
the screen size and required distance.
(Continued)
Floor-mounted front...

CONTENTS19Connections and installation
(Continued)
1Place the projector on a steady,
level surface such as a table.
Point the projector squarely at the screen
for the best possible picture.
Point the lens straight at the center of the
screen as above.
Place the projector horizontally so that the
projecting light hits the screen squarely.
Top view
Side viewa: Distance between the lens and the screen
b: Distance between the lens height and the
bottom of projection area
Adjust the distance between
the lens...

CONTENTS20Connections and installation
Notes
¥ When the projector is moved from a cold
location to a warm location, or when the
ambient temperature in the projection room
has risen suddenly, moisture may condense
on the lens or the mirror to blur the projected
pictures. In such a case, leave the projector
for an adequate time (1 to 2 hours, depending
on the roomÕs condition) before using it so it
adjusts to the ambient temperature.
¥ If the screen is exposed to direct sunlight or
other strong light, the...