Toshiba Projector Tlp 560 User Manual

11
Before use
CONTENTSNames of each part on the main unit
Continued
Infrared remote sensor
Air intakeInfrared
remote sensor Control panel Lens shift dial
Zooming lever
Focusing ring
AC IN socket
Left side
Speaker
Carrying handle
Open to carry the projector.
Anti-theft lock holeLensLens cover
Foot adjusterFoot adjuster release button Air intake
Rear sideAir exhaust
Right side
Front side
1916
31
31
212120
12
CAUTION
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of...

12
Before use
CONTENTSNames of each part on the main unit (continued)
35 34 43 32 28 33 6161 28 33 61 28 33 6133 28
44
3843
30TEMP indicator
KEYSTONE button
To correct the keystone distortion of
the picture.
FA N indicator LAMP indicator ON indicator
INPUT button ENTER button  Selection buttons EXIT button
VOL/ADJ buttons 
AUTO SET button  MENU buttonON/STANDBY button
Top side
Control panel
To set and/or adjust values on the menu.
To adjust the volume when the menu is not 
displayed.To indicate the...

13
Before use
CONTENTS
AUDIO IN jack          - 
(ø 3.5mm stereo mini-jack)
To enter audio signal from a computer 
or a video equipment.
USB connector
To connect to a USB connector of a
computer when using the presentation 
mode.
CONTROL connector
(RS-232C connector)
To connect a computer to control the
projector. 
VIDEO IN jack
To enter video signal from a video
equipment, etc.
S-VIDEO IN connector
To enter S-Video signal from video
equipment, etc.
COMPUTER IN connector
To enter RGB signal from a...

14
Before use
CONTENTSNames of each part on the remote control
MENU
ON /
INPUT
ENTER
CT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
30
35
37
39
36
44
3228 33
34
38
40
3843 44
41
To display the menu screen
and/or select the operation 
on the menu screen.
 
Use the selection buttons and
EXIT button to enlarge the
image           and to operate 
the presentation mode.
INPUT button
To select the input source.
KEYSTONE button
To correct the keystone distortion 
of the...

15
Before use
CONTENTSLoading batteries
Notes
Using batteries incorrectly can cause them to leak
or burst. Strictly observe the following.
•Install the batteries with their + and – ends facing
correctly.
•Do not charge, heat, disassemble, or short the
batteries or throw them into a fire.
•Do not leave any exhausted batteries in the
remote control.
•Do not mix different types of batteries or new and
old batteries.
•When you will not be using the remote control for
a prolonged period, take the batteries...

16
Before use
CONTENTSRemote control operation
Point the remote control at the infrared remote sensor and press a button.
Notes
•The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the projector’s remote sensor.
•Operate the remote control from a position where the remote sensor is visible.
•Do not drop the remote control or otherwise jolt it.
•Keep the remote control out of locations with excessively high temperature or humidity.
•Do not...

17
Installation and
connections
CONTENTSFloor-mounted projector placement
Floor-mounted front projection
Viewing a picture projected on the front of the
screen from a floor installation.
Floor-mounted rear projection
Viewing a picture projected through the back of the
screen from a floor installation.
Viewer Translucent screen
Viewer There are two ways to place the floor-mounted projector.
When the projector is mounted in the rear projection mode, the picture is reversed.  Set the “Projection mode” (on...

18
Installation and
connections
CONTENTS
Place the projector on a steady, level surface such as a table.
To obtain proper screen projection, place the projector so that the light beam hits the screen squarely.
Floor-mounted projector placement (continued)
Top view
Screen
Screen
a
90°
Side view
90°
Screen
Projection size
(inches)
30
36
50
80
100
120
150
180Minimum
(At maximum zoom)
–
0.70
0.98
1.59
2.00
2.41
3.02
3.63Maximum
(At minimum zoom)
0.70
0.85
1.19
1.92
2.41
2.89
3.63
–
a (m)
• The values are...

19
Installation and
connections
CONTENTS
Connect the power cord.
• Insert one end into the AC IN socket on the projector.
• Insert the other end into a wall outlet.
Notes
•When the projector is moved from a cold location to a warm location, or when the ambient temperature in the projection room has risen suddenly,
moisture may condense on the lens or the internal optical section to blur the projected pictures. In such a case, leave the projector for an adequate time
(1 to 2 hours, depending on the room’s...

20
Installation and
connections
CONTENTSLens shift function
When turning the lens shift dial, the lens moves to upward or downward and the projection position on the screen is to be adjusted.
At shipping from factory, it is set to the state turned clockwise fully (the highest projection position).
Refer to “Projection on the screen”  
28, and adjust it after projecting a picture.
90°50%
50%90°
10% 90%
When the lens shift dial is turned counterclockwise
fully, the projection position becomes the...