Toshiba Projector Tlp 551 User Manual

							51CONTENTS
Adjustments &
Settings
FULL MENU settings - Reset
Return the adjustments and settings of all menus to the factory default setting.Reset allEXEC.
You can return the adjusting and setting values of all menus to the factory default setting.
Note
The resettings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button. If the power cord is
unplugged or if a power failure occurs while the projector is on, the resettings are not memorized. 
						

							52CONTENTS
Adjustments &
Settings
PIP menu setting
Return the settings of PIP MENU to the factory default setting. Select the signal source for PIP sub-picture.
Set the PIP sub-picture size.: Video input is selected as signal source.
: S-Video input is selected as signal source.
: The PIP sub-picture size is set to small.
: The PIP sub-picture size is set to medium.
: The PIP sub-picture size is set to large.
Set the PIP sub-picture display position.
:
The sub-picture is displayed at the upper left of the screen.
:The sub-picture is displayed at the upper right of the screen.
:The sub-picture is displayed at the lower left of the screen.
:The sub-picture is displayed at the lower right of the screen.
ResetEXEC.
Source
SETVideo
SETS-Video
Size
SETSmall
SETMedium
SETLarge
Position
SET
SET
SET
SET
When a PIP sub-picture is displayed, the PIP menu screen will appear if you press the MENU button.
You can make the PIP sub-picture settings when a PIP subpicture is displayed.
To cancel the menu, press the EXIT button.
Notes
•The size of the PIP sub-picture differs according to the signal type (resolution) of the main picture.
•The settings made are memorized automatically when the power is turned off by pressing the ON/STANDBY button. If the power cord is unplugged or if a
power failure occurs while the projector is on, the settings are not memorized. 
						

							53CONTENTS
Document
imaging camera
Camera head
Camera lensArm
Infrared remote sensor LED light
Camera control panel
Focusing ringLOCK (W.BALANCE) indicator 
Lights when the white balance is locked.
W.BALANCE button 
To switch white balance settings between 
automatic adjustment and lock.
ARM LIGHT button 
To turn on or off the light.
CAMERA GAIN (+/
-) buttons 
To adjust the camera gain.CAMERA button 
To select the camera source. Press again 
to return to the previous input source.57
56
55
58
58
16
56
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN
IEC 60825-1,
Am.1  1997LED RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LED PRODUCT
WAVE LENGTH : 425-750nm
MAX OUTPUT : 
LESS THAN 1mWRAYONNEMENT LED
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LED DE CLASSE 2
LONGUEUR DONDE : 425-750nm
PUISSANCE MAXIMA : 
AU-DESSOUS DE 1mWLED-STRAHLUNG
NICHT IN DEN STRAHLBLICKEN
LED KLASSE 2 PRODUKT
WELLENLÄNGE : 425-750nm
MAX AUSGANGSLEISTUNG :
UNTER 1mW
Part names (of the document imaging camera model)
CAUTION
When using the camera, be careful not to
pinch your hand or fingers into the arm.
On the document imaging camera model, you can
project pictures using the document imaging camera.
The document imaging camera can directly project any
materials (documents, illustrations, etc.) without using an
OHP film. 
						

							54CONTENTS
Document
imaging camera
Note
Never give shocks or impacts to the camera or arm as this may cause malfunction.
Preparation of the document imaging camera
1) Raise up the arm.
Before preparations
(stowed away)2) Pull up the camera head. 3) Turn the camera head.
4) Incline the arm backward. 6) Pull up the light. 7) Turn the light.
5) Move the camera head 
toward the object. 
						

							55CONTENTS
Document
imaging camera
Picture projection with the document imaging camera
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN1
CAUTION
Do not look into the arm light while it is lit.Preparation
1Project a picture on the screen as explained in the step “Projection on the screen”. 27
Press ARM LIGHT.
The light turns on.1
ARM LIGHT
Set a document to be projected.
Place the document (illustrations, etc.) onto or around the
projector, and turn the camera head to the direction of the
document.2
123
123
123
123
123
Continued Images on the screen
Setting direction
Camera control panel
Notes
•Do not leave documents on the unit or near of the air exhaust for long periods of time. The
heat could erase or discolor the letters on a thermal paper.
•Use the arm light when necessary according to the brightness of the room. 
						

							56CONTENTS
Document
imaging camera
Press CAMERA to select the camera input mode.
•Pressing CAMERA again will return the input selection to the
previous mode.
•You can also select it by pressing INPUT on the remote
control or on the main unit. Set the input source on the menu
screen when selecting by the INPUT button. 
29
•The CAMERA button can be used regardless of the input
setting.
•“Camera” is displayed when the picture switches to the
document imaging camera’s picture.
3
Continued
MENU
ON /INPUT
ENTER
CT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
3
3
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN
3
Picture projection with the document imaging camera (continued)
Move the camera head to adjust the size of the picture.
4
Focus on the picture by turning the focusing
ring on the camera head.
5
123
Up: To reduce.
Down: To enlarge.
Focusing ring
Remote control
Control panel
(Main unit side)
Camera control panel
INPUT INPUT
CAMERA 
						

							57CONTENTS
Document
imaging camera
Press CAMERA GAIN (+/-) to improve view of a
camera subject which is too dark or vivid.
6
Notes
•You can adjust the “Sharpness” of the camera image on the menu screen. 45
•If the image flickers due to a fluorescent light in the room, either turn off the fluorescent light or
set the “Shutter” on the menu screen. 
45
Note that the image may still flicker due to the lighting, the document status, the image
adjustment, etc., even if the “Shutter” setting is changed.
CAMERAGAIN
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN
6
Picture projection with the document imaging camera (continued)
When finished, turn off the light and close it,
and put back the arm.
Follow the steps of “Preparation of the document imaging
camera” in reverse.
7
Notes
•The light turns off automatically when the arm is inclined.
•When the arm is not raised up, the camera source cannot be projected.
•In the camera input selected, the sound is not emitted.
Camera control panel 
						

							58CONTENTS
Document
imaging camera
This projector ’s camera is always being adjusted automatically for projected color balance;
however, the balance can shift away from optimum due to the color scheme of the
document. Should this occur, the white balance can be set to a fixed condition by using the
following procedure.
1
Project a white paper and enlarge it to fill the
screen.
Notes
•If you raise up the arm while the camera input is being selected, the color of the picture may
vary for an instant due to the automatic white balance adjustment. This is not a malfunction.
•If you put the arm back and raise it again while the white balance is locked (the LOCK
indicator is lit), the projector will release the white balance.
•Should this be the case, or if you would like to adjust it to a desired tint, adjust
“R-level”, “G-level” or “B-level” on the FULL MENU [Color] screen.
Locking the white balance
LOCKW.BALANCE
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN
2
2
Press W.BALANCE to turn the LOCK indicator
on.
The white balance is locked.
To release the white balance, press W.BALANCE again to turn
the LOCK indicator off. Camera control panel 
						

							59CONTENTS
Document
imaging camera
With the document camera operating, fully
cover the camera lens with a piece of black
paper or cloth.
1
Correcting illuminated defects
Note
Do not press ARM LIGHT and EXIT buttons simultaneously if the camera lens is not
covered. Doing so will not only erase the white spot correction data already set but also
result in parts ot the image that are properly displayed being corrected. Also be careful if
the camera input mode is not selected.
ARM LIGHT
EXIT
CAMERA
ARM LIGHTLOCKW.BALANCE
CAMERA
GAIN
2
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
Press ARM LIGHT on the camera control panel
and EXIT on the projector’s control panel
simultaneously.
You can not use the remote control buttons.
2
Camera control panelControl panel
(Main unit side)
Press both sides
Camera lens
For the CCD image sensor used in the camera unit, in rare cases some of the pixels may
be disturbed due to the influence of cosmic rays, etc. This disturbance may cause white
spots to appear on the picture.
If white spots appear on the document camera image, use the procedure described below
to correct the problem. 
						

							60
Maintenance
CONTENTS
If there is some problem inside the projector,
the indicators light up or blink.
Trouble indications
Indicators
Or(Lit in red) (Off)
ONLAMPTEMPFA N
(Lit in red)(Lit in red)
ONLAMPTEMPFA N
(Flashing 
  in orange)ONLAMPTEMPFA N
(Lit in red)
ONLAMPTEMPFA N
(Lit in red)
Or
(Lit or flashing 
     in red)
(Lit or flashing
      in orange)
Or
Or
Or
(Lit in red)(Lit in red)
(Lit in green)
(Lit in green) (Lit in orange)
ONLAMPTEMPFA N
(off)
The power does not come on.→Malfunction of the unit.
• Unplug the power cord and call the dealer.
The lamp turns off or does not light up. →The projector will return to the standby mode in about 2 minutes.
If the projector does not operate normally when the power is switched on again, 
the lamp is at the end of its life duration or the unit has a fault.
• Lamps life duration is over, replace the lamp with a new one.
• Unplug the power cord and call the dealer.
The power turns off or does not come on. → The inside is too hot, or the projector has been working in an area of high 
temperature.
• Place the projector correctly so the intake and exhaust fans holes are not covered.
• Turn the projector off, and leave it for a while, and turn it on again.
• Clean the air filter.
* The         icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown 
for about 2 minutes.
The power turns off or does not come on.→ Trouble with the cooling fan.
• Unplug the power cord and call the dealer.
* The         icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown 
for about 2 minutes.
The power turns off or does not come on. →The lamp cover is not properly attached.
• Unplug the power cord and reattach the lamp cover.
* The         icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown 
for about 2 minutes.
64
61
65
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
Control panel
(Main unit side)
Notes
• If abnormality occurs while operating, unplug the power cord.
• When reinserting the power cord before the lamp has cooled, please wait until the lamp has
cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the
life duration will be shortened.