Toshiba Projector Tdp S21 User Manual

							21
20
Preparations
MONITORCOMPUTER 2 INY/PB/PR
(
)
AUDIO OUTAUDIO IN
CONTROL
S-VIDEOVIDEO
COMPUTER 1 INY/PB/PR
(
)
R
L
p.47
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.45
, etc.
•Turn off the power of both devices before connecting.
•The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Notes
•COMPUTER terminals 1 and 2 function identically.
•For TDP-S21, the document camera should be connected to COMPUTER terminal 2.
•The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.Connection
To audio
output To  RGB
outputControl cable To RS-232C terminal
RGB cable
(not supplied)
To  Y/C
B/CR output
Green (Y)/Blue (C
B)/Red (C
R)
VCR
S-Video cable
(not supplied) Video cable
(not supplied)To S-Video
output
To audio output
White (L)/Red (R)
Computer
(for control)
Conversion adapter BNC-pin
(not supplied)
Monitor cable Mini D-sub
15P-BNC
(not supplied)
Audio cable(not supplied)
Video recorder,
DVD player, etc.
Projection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the Projection mode in the
default setting menu 
p.32
, in accordance with your needs.
PlacementFloor-mounted front projection 
 WARNING
•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
•If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
•If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
Floor-mounted rear projection 
Ceiling-mounted front projection 
Ceiling-mounted rear projection 
a
H
90°
a is the distance (m) between the lens and the
screen, and corresponds to a range of 1.15 m to
10.00 m. H is the height from the image bottom to the
center of the lens.Screen
As seen from above
Lens center
As seen from the side
a (min length) = projection size (inches) – 1.516
29.85a (max length) = projection size (inches) – 1.264
24.88
Audio amplifier, etc.
To audio
output
White (L)/
Red (R)
DVD video recorder, etc. Computer ComputerRGB cable
(supplied with
TDP-S21)
Audio cable(not supplied)
RGB cable
(supplied)To  RGB
output Audio cable
(not supplied)
To audio input
White (L)/Red (R)
AV cable
(not supplied)
To audio
outputTo video
output
Document camera
90°
projectionprojection distance a (m)
height (H)
min length max lengthsize (inches)
(zooming max) (zooming min)(cm)
30 — 1.15 5.536 1.15 1.40 6.640 1.29 1.56 7.360 1.96 2.36 11.080 2.63 3.17 14.6100 3.30 3.97 18.3150 4.97 5.98 27.4200 6.65 7.99 36.6250 8.32 10.00 45.7
300 10.00 — 54.9 
						

							23
Operations
22
■ Connecting the power cord1
Insert the power cord connector into the
AC IN socket of the projector.
2
Insert the power cord plug into a wall or
other power outlet.
■ Turning the power on1
Turn on the main power switchThe ON indicator will change to
orange, indicating standby mode.
2
Press the ON/STANDBY
button.The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
Start-up screen Control panelRemote
Control
Notes
•The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.31
.
•The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed 
p.24
.
■ Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling complete
(Orange) (Orange)
A(Green)(Green)
(Off)
(Orange)
B
C
Flashing(Green)
(Off)
(Off)
LAMPTEMP
FA N
LAMPTEMP
FA N
LAMPTEMP
FA N
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
C
In standby mode
Note
•The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
PRECAUTION
•If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and
its lifetime will be shortened.
(Orange)LAMPTEMP
FA N
(Supplied) Power cord connector
 CAUTION
•Do not look into the lens while the lamp is on.  The strong light from the lamp may cause
damage to your eyes or sight.
•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
Turning the power on and offOperations 
						

							25
Operations
24
1
Turn on the power.Turn on the power by following the instructions in “Turning on the power” 
p.22
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 
6.)
qUse the 
 or 
 button to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
wUsing the 
 or 
 button, select Standard
or Low for the lamp power (menu item)
and press the  button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes•When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Default setting menu 
p.32
, the Language and Lamp power menus will be
displayed the next time when the power is turned on.
•The language can also be set via the Display setting menu 
p.31
 and Lamp power
via the Default setting menu 
p.32
.
•This owner’s manual assumes that English has been selected.
3
Activate the connected device.Turn on and start the connected device such as a computer.
4
Press the INPUT button.An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment.
Basic operations
Notes
•When [Auto input search] is set to [On] in the default setting menu 
p.32
, the image
of the equipment which is connected and turned on is projected.
•Moving pictures generated with the DVD software for computers may appear unnatural if
it is projected with this projector, but it is not a malfunction.
English
Français
PortuguêsDeutsch
Italiano
Español
................
..............
..............
................
...............
..........
...............
..............
................
.................
.......
.......
...................
Russian
Swedish
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Türkçe
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTurn the foot adjuster to fine-tune
the angle.
eTo adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6
Adjusting the screen size and focusqUse the zooming lever to adjust the screen
size.
wUse the focusing lever to adjust the focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes
•Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out.  This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
•The DMD
TM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.  Please
note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.45
, any resolutions not
supported by this projector (SVGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to SVGA (800 × 600) resolution.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If a signal not supported by the projector is input, the “Unsupported signal” will appear.
•If no signal is being input from the connected device, the “No signal” will appear.
•If an unavailable operation button is pressed, the 
 icon will appear.
1
2
3
12 
						

							27
Operations
26
■Using auto setting
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.1
Press the SET UP button.The Set up menu appears.
2
Press the SET UP button again.The menu item is automatically adjusted/set.
For computer input, the 
 icon will appear during
processing.
For manual adjustment and setting, see the following table 
p.27
.
Notes•The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector 
p.45
, p.46
.
•Keystone adjustment cannot be corrected automatically.
●Correcting the keystone distortion
When the foot adjuster 
p.25
 is used to change the projector placement angle while
projecting the image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion
.
●Manual adjustment
Press the SET UP button to display the Set up menu and select [Keystone]. Use
the 
 
 buttons for keystone adjustment. When the adjustment is finished, press
the RETURN button. The menu disappears.
Notes•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
•Keystone adjustment is available for the keystone distortion in a slant angle of ±15
degrees.
•Keystone adjustment will not change the shape of the menus, the start-up screen,
and the background (with no signal input).
Using handy features
Control panelRemote
Control
Before correction
After correction
●Manual adjustments and settings
The menu items of the Set up menu vary depending on the input type, as shown in
the table below.
Use the 
 
 
 
 
 buttons to adjust the items in the table below, then press
the RETURN button when you are finished.
Select Item Description
Computer Camera
Y/P
B/PR
Video
S-video
KeystoneCorrect the keystone (trapezoid) distortion of the 
screen.
Screen shrinking             Screen shrinking
downward                        upwardAuto setting
Automatically adjusts items such as the sampling 
phase depending on the type of input signal.
Press the SET UP button.
PhaseAdjust with            to eliminate flicker.
FrequencyAdjust with             to eliminate periodic patterns 
and flickering when many vertical lines appear 
on the screen.
H-positionAdjust the horizontal position of the image.
Move left            Move right
V-positionAdjust the vertical position of the image.
Move down            Move up
Clamp 1Adjusts the clamp pulse position.
Lower            Higher
Clamp 2Adjusts the clamp pulse width.
Narrower            Wider
Ye s Ye s Ye s Ye s
Ye s N o N o N o
Ye s N o N o N o
Ye s N o N o N o
Ye s N o N o N o
Ye s N o N o N o
Ye s N o N o N o
Ye s N o N o N o 
						

							29
Operations
28
Using handy features (Continued)■Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)Notes•The 
 icon will appear while mute is in effect.
•Operating any other functions will also cancel the muting.
■Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture pauses. (The Freeze function is released when pressing
the FREEZE button again.)Notes•The 
 icon will appear while freeze is in effect.
•Other operation will also release the freeze.
•Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
•If you use this function on video software sold on the market, broadcast or
broadcast on cable except for the purpose of your private viewing and listening, it
may infringe the copyright protected by the copyright laws.
Remote
Control
Remote
Control
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons 
p.16
 on the control panel (main unit side) and remote control.
■How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Using the menus
Note
•Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
Display the Setting display menu
The menu disappears.
1. Press the MENU button
2. Select a Category
3. Adjustments & Settings
4. Back5. End
    
Press the MENU 
    button
Select a category by using  
         .
There are following four 
categories:Displays the current 
adjustments and settings of 
selected category.
Item shown with gray cannot 
be adjusted with the current 
input source.p.30
Image adjustment menu
p.31
Display setting menu
Default setting menu
p.32
Status display menu
p.33
The figure shows displays given for operation instructions purposes.  As the display 
may differ depending on the item, use the following pages as a reference.
ItemAdjustment/Setting Value
These marks signify the 
items can be adjusted/set 
by using                .
These marks signify the items can 
be selected from the list by using
           .
After an item is selected, apply it 
by pressing      .
Press      to open the menu.
This mark signfy that 
there are options.
Press         to display a 
list of options. 
						

							31
Operations
30
■The image adjustment menuUse this menu to adjust image-related items.Items that can be adjusted are marked with  “Yes”, and those that cannot are marked with “No”.
Item    
  
Description
Computer
Y/P
B/PR
Video
CameraS-video
 
ContrastAdjust the image contrast. Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes
Darker
Brighter
ColorAdjust the color of the image. No Yes Yes No
Lighter
Deeper
Tint 
*1
Adjust the tint of the image color. No No Yes No
Reddish
Greenish
SharpnessAdjust the sharpness of the image. No Yes Yes Yes
Softer
Sharper
NoiseSet the function to reduce screen noise. No Yes Yes No
reduction
On (Enable)
Off (Disable)
PicturePress 
. Toggle the picture mode with Yes Yes Yes No
mode
 / 
.
Bright/Standard/True color
R-levelAdjust red of the image color. Yes Yes Yes Yes
Less red
More red
G-levelAdjust green of the image color. Yes Yes Yes Yes
Less green
More green
B-levelAdjust blue of the image color. Yes Yes Yes Yes
Less blue
More blue
NTSC mode
*1
Set the black level with 
 / 
 button. No No Yes No
US: NTSC (US) mode
Japan: NTSC (JAPAN) mode
ShutterSet the shutter speed of the camera to No No No Yes
the local power frequency.
(TDP-S21)50 Hz
60 Hz
WhiteSet the white balance of the document No No No Yes
balance
*2
camera.
(TDP-S21)Auto
Lock
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to
[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is
set to US for other languages.)
*2: Even if the white balance is set to [Lock], turning  the projector off disables this function and
turning it on again the next time resets the menu to [Auto]. (TDP-S21)Using the menu (Continued)
■The display setting menuUse this menu to set screen display-related items.
(Full):  Display with 800 × 600 dot resolution
(Thru): 
Display with sampling resolution (for computer/camera input)
(Wide):  Wide-screen display (for Video, S-video, and Y/P
B/PR)
Select one of the languages below to use for displaying the menu and messages[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/Português/Russian/
Swedish/Türkçe/            /                      /                      /Screen to display when there is no input signal                        
 (Logo)                            (Blue)                            (Black)
Display icons as function guidesOn Off
Display start-up screen when power is turned on On Off Description
Item
Screen size
Note
•If “Thru” is selected for screen size, portions exceeding the native resolution (800 × 600
pixels) will not appear on the screen. Note that for RGB signals with clock frequency
110MHz or lower, all input pixel signals are sampled. However, if the clock speed is
higher than this, the RGB pixel signal is thinned before sampling. 
						

							33
Operations
32
Using the menu (Continued)
■Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video
CameraS-video
Input Input source name Yes Yes Yes YesMode name RGB input mode 
[Note 1]
Ye s N o N o N o
H-resolution Horizontal resolution (in dots) Yes No No NoV-resolution Vertical resolution (in dots) Yes No No NoH-frequency Horizontal sync frequency Yes No No NoV-frequency Vertical sync frequency 
[Note 2]
Ye s N o N o N o
Sync Sync signal polarity 
[Note 3]
Ye s N o N o N o
Signal format Y/P
B/PR signal format No Yes No No
Video mode Color method of video signal No No Yes NoLamp time Time of lamp use 
[Note 4]
Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes YesTotal time
The total time that this projector is used
Ye s Ye s Ye s Ye s
Version Firmware version 
[Note 5]
Ye s Ye s Ye s Ye s
Notes
1:The mode of supported RGB signals 
p.45
 is shown.
2:Same as the refresh rate of the computer signal.
3:Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult
with a store about getting a TLPLV4 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note•The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
■The default setting menuThis menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.  Set the timer to wait for the power to be turned off after signal input stops.Press      . Switch with       and      .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Set whether the input with signals is only selected or not.Sets whether to turn on the power when the ON/STANDBY button is pressed 
(Manual), or when the power cord is plugged in (Auto).   Manual             AutoSets the lamp power.                                   
Sets the cooling fan speed.Press       .
Resets all adjustments and settings to their factory settings.
Description
Item
Projection
mode
No signal 
power off
Auto input 
search
Power on
Lamp power 
[Note 1]
Fan mode
 [Note 2]
Reset all
(Rear mounted from ceiling)
(Standard)
(Rear)(Mounted 
from ceiling)
On            Off
Standard           High
Yes           No  Low           Standard
p.20
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
2: Setting [Fan mode] to [High] increases the cooling fan speed.  Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
•Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.•When you turn off the projector even if Power on is set to Auto, you must press the ON/
STANDBY button to turn the power off. 
						

							35
Operations
34
Using the document cameraPlease read this chapter if the model you purchased is TDP-S21 which includes a document camera.■How to use the document camera
Using the camera attached on the projector
PRECAUTIONS
•For camera interconnection, be sure to use the supplied RGB cable (25 cm or 3 m). If you
use the other cables, the normal operation may not be achieved and even the malfunction
may result.
•When moving the projector with the camera attached, do not grab the camera arm and/or
the camera head.
•When moving the projector with the camera attached, first ensure that the camera is securely
locked in position on the tray
.
•Insert the RGB cable straight and securely until it is fixed in place.
•Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
•Note that when extending or rotating the camera arm, the arm moves in an arc. Take care
not to bump yourself or others with it.
•When placing the projector in the carrying bag, remove the connection cables. Otherwise,
damage to the connectors and cables may result.
Status before preparation
(When stored)1) Set up arm. 2) Rotate arm.
3) Raise camera head.
Using the camera removed from the projector
2
1
1
PRECAUTIONS
•Installation of the document camera onto the tray should be performed in the reverse
order shown above.
•When replacing the document camera on the tray, ensure that the lock lever is securely
locked in position.
•When using the tip resistant bars, pull them fully until each forms the angle of 90 degree.
If you don’t use the bars, the camera may topple over.
Status before preparation
(When stored)1) Disconnect the RGB
cable, then slide the
lock switch to release
lock.2) While pushing the lock
lever in the arrow
direction, lift up the
document camera.
4) Extend the tip resistant
bars to set the
document camera.5) Connect the document
camera and the
projector using the
supplied RGB cable. 3) Remove the document
camera from the tray.Pull up toward direction 
q 
						

							37
Operations
36
■Image projection with the document camera1
Place the document.Set the document at the side of the projector
.
2
Press the CAMERA button, and select camera input.•The input returns to the previous input when the CAMERA button
is pressed again.
•Camera input can also be selected by pressing either the remote control or projector’s
INPUT button.3
Rotate the camera head to align the orientation of the document for
shooting by checking the screen.
4
Move the camera arm up and down to adjust the image size.•Closeup shot with the distance shorter than 100 mm cannot be performed.5
Adjust the focus using the focusing lever on the camera head
Focusing lever
Rotate the focusing lever to either NEAR or
FA R, whichever is better in focusing.
•Near: 100 mm to 300 mm
Far: 300 mm to 5 m
Using the document camera (Continued)
Farther (↑): Smaller image
Closer (↓): Larger image
6
If the screen is too dark or too bright, use the CAMERA GAIN (+/–)
buttons to make it easier to see.The Sharpness of the camera image can also be adjusted using
the Image adjustment menu 
p.30
.
7
After use, fold up the document camera.Fold up the camera using the reverse order from unfolding the document camera 
p.34
.
Notes
•There is no audio output when camera input is selected.
•If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent
light, or set the Shutter from the Image adjustment menu 
p.30
. Note that changing the
Shutter setting may not eliminate the flicker, depending on the lighting, state of the
document, or image adjustment.
■Locking the white balance
Although the projector’s camera is constantly adjusting the color balance of the images
it photographs, the color balance may be disrupted, depending on the color layout of
the document. If this happens, the white balance can be locked using the procedures
below.
1
Lay down a piece of white paper, and adjust so it fills the screen.Adjust the camera head and arm so that the white
paper fills the screen completely.
2
Set the White balance to Lock in the Image adjustment menu. 
p.30
The white balance is locked. If you want to return to the auto adjustment, set the White
balance to Auto in the Image adjustment menu.Notes
•If the white balance is set to Lock, once power is turned off, the setting goes back to
Auto.
•The color of the room lighting may prevent the white balance from being adjusted to the
optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level,
G-level and B-level on the Image adjustment menu 
p.30
. 
						

							39
Maintenance
38
1
Unplug power cord.
2
Wait until lamp is sufficiently cooled.Wait for at least 1 hour.
3
Remove the lamp cover.Loosen the 2 screws, then pull up to the
direction of the arrow with your fingers as
shown to remove the lamp cover. Use care to
av oid any damage to nails and/or tip of your
finger(s). If you have any difficulty in removal,
y ou can use a screwdriver or any other smaller
tool for your convenience.
4
Pull out the lamp.Loosen the 2 screws holding the lamp in place,
and pull up the handle to remove the lamp.
5
Mount the new lamp.Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
6
Replace the lamp cover.Align the cover, and press it in, then tighten the
screws loosened in step 
3 until the lamp cover is
no longer loose.
7
Reset the lamp timer.See the lamp’s manual for instructions on resetting
the lamp timer.Notes and Precautions
• Press the 
 button twice to display (a rough guide) the time of lamp use, the  Lamp time
item, in the  Status display menu . 
p.33
•It is recommended that the lamp be replaced after 3,000 hours of use. When  Lamp time
reaches 3,000 hours, the 
 icon and a message will appear. This display disappears
when you press 
  b utton.
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on 
p.41
, and the lamp’s lifetime may be shortened.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
12122
1
345
Lamp cover
About lampMaintenanceThe product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.•The lamp may explode with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•H ow long it takes before the lamp explodes or the life expires may vary greatly by lamp.
Some may explode shortly after first use. (Free replacement is available if the lamp
e xplodes within the warranty period. Contact the dealer from whom you purchased the
product in such a case.)
•Explosion is likely to happen if the lamp is used after the replacement period has elapsed.• When the lamp explodes, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
• When the lamp explodes, a slight amount of mercury gas enclosed in the lamp along
with glass dust may be released from the openings for ventilation.■
Immediately replace the lamp when a sign appears on the screen.•When the replacement time approaches, a message will appear on the screen.
•The risk of explosion will increase if the lamp is continuously used without being replaced.•F requently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. 
p.33
)
■
When the lamp is broken• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp explosion, unplug the product from the wall outlet, leave and
completely ventilate the room. Then, thoroughly clean the area around the projector and
discard any edible items placed in that area.
• When the lamp explodes, consult a doctor if glass dust or mercury gas gets into your
ey es or you breathe it.Lamp replacementA lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one
.
 W
ARNING
•If the projector is mounted on a ceiling, request a lamp replacement fro\
m your projector dealership.•When replacing, always use lamp “TLPLV4” (sold separately).
 CAUTION
•If you have been using the projector, the lamp will be very hot, and may cause burn injuries
.
W ait for the lamp to cool (for longer than 1 hour) before replacing it.
•
If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.