Toshiba Projector Tdp P8 User Manual
Have a look at the manual Toshiba Projector Tdp P8 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 33
34
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Using the menu (Continued)
ItemDescriptionComputerY/PB/PRVideo
S-video
InputInput source nameYesYesYes
Mode nameRGB input mode [Note 1]YesNoNo
H-resolutionHorizontal resolution (in dots)YesNoNo
V-resolutionVertical resolution (in dots)YesNoNo
H-frequencyHorizontal sync frequencyYesNoNo
V-frequencyVertical sync frequency [Note 2]YesNoNo
SyncSync signal...](http://img.usermanuals.tech/thumb/76/96651/w64_toshiba-tdp-p8-manual_d-32.png "Page 33
34
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Using the menu (Continued)
ItemDescriptionComputerY/PB/PRVideo
S-video
InputInput source nameYesYesYes
Mode nameRGB input mode [Note 1]YesNoNo
H-resolutionHorizontal resolution (in dots)YesNoNo
V-resolutionVertical resolution (in dots)YesNoNo
H-frequencyHorizontal sync frequencyYesNoNo
V-frequencyVertical sync frequency [Note 2]YesNoNo
SyncSync signal...")
![Page 35
36
4. Verify the resolution setting is less than or equal to 1280 x 1024
resolution.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the computer.
2. Press the toggle output settings. example:[Fn]+[F4]
If you experience diffi culty...](http://img.usermanuals.tech/thumb/76/96651/w64_toshiba-tdp-p8-manual_d-34.png "Page 35
36
4. Verify the resolution setting is less than or equal to 1280 x 1024
resolution.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the computer.
2. Press the toggle output settings. example:[Fn]+[F4]
If you experience diffi culty...")
![Page 38
39
Notes and Precautions
•
It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]
reaches 2,000 hours, the icon
and a message will appear with a beep sound. (After
2,000 hours, they will appear when the power is on at the fi rst time every 100 hours.) This
display disappears when you press
button.
•
Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,
the projector may fail to be powered on or the lamp...](http://img.usermanuals.tech/thumb/76/96651/w64_toshiba-tdp-p8-manual_d-37.png "Page 38
39
Notes and Precautions
•
It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]
reaches 2,000 hours, the icon
and a message will appear with a beep sound. (After
2,000 hours, they will appear when the power is on at the fi rst time every 100 hours.) This
display disappears when you press
button.
•
Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,
the projector may fail to be powered on or the lamp...")
42 About Lamp About Lamp The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure to fully understand the following character- istics of the lamp and handle it with extreme care. • The lamp may burst with a loud noise due to impact or deteriora- tion, or fail to light at the expiration of its life. • How long it takes before the lamp bursts or the life expires may vary greatly by lamp. Some may burst shortly after fi rst use. • Burst is likely to happen if the lamp is used after the replacement period has elapsed. • When the lamp bursts, the broken pieces of glass may get inside the product or be released outside from the openings for ventilation. • When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with glass dust may be released from the openings for ventilation. Immediately replace the lamp when a sign ap- pears on the screen. • When the replacement time approaches, a message will appear on the screen. • The risk of burst will increase if the lamp is continuously used with- out being replaced. • Frequently check the used hours and prepare spares when the replacement time approaches. When the lamp is broken • If glass components, including a lamp and a lens, should break, handle the broken pieces with care to avoid injury and contact your dealer for repair service. • In the event of lamp burst, unplug the product from the wall outlet, leave and completely ventilate the room. Then, thoroughly clean the area around the projector and discardany edible items placed in that area. • When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes or you breathe it.
43
About Lamp
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images
will appear dark, and the lamp could burn out. This is characteristic of a
lamp, and is not malfunction. (The lifetime of the lamp depends on condi-
tion of use.) If this happens, replace it with a new one.
CAUTION
If you have been using the projector, the lamp will be very hot, and may
cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to
broken pieces and contact your dealer for repair service.
Lens cleaning
• Clean the lens with a commercially available
blower and/or lens cleaner.
• The lens is easily scratched, so do not rub it
with hard objects, or strike it.
Main unit cleaning
• Clean the main unit after unplugging the
power cord.
• Wipe dirt off the main unit gently with a soft
cloth.
• Do not wipe the main unit with a damp cloth.
Doing so may allow water to get inside, result-
ing in an electric shock or failure.
• Do not use benzene, thinner and the like as
they may deform or discolor the unit or dam-
age the paint surface.
• When using a chemically treated cloth, follow
the precautions included with the cloth.