Toshiba Projector Tdp P75 User Manual

Overview 21
English
Operating a computer using the remote 
control
A computer can be operated using the projector’s remote control. This function is 
available on any computer with the Windows 98/98SE, Windows Me, Windows 
2000, or Windows XP OS, that is equipped with a USB port supporting the USB 
1.1 (The mouse remote control is supported on OS 9 or OS X for the Macintosh).
The operation cannot be guaranteed for all the environments of computers.
Connecting a computer
Connect the supplied Mouse remote...

Overview 22
English
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation 
locations: 
1. Floor in front of screen; 
2. Ceiling in front of screen; 
3. Floor at rear of screen;
4. Ceiling at rear of screen. 
Your room layout or personal preference will dictate which installation location you 
select. Take into consideration the size and position of your screen, the location of 
a suitable power outlet, as well as the location and...

Overview 23
English
•  If the projector is ceiling-mounted, install the breaker for turning off the power in 
case of anomaly. Let everyone involved with the use of the projector know that 
fact.
Projection distance and size
Use the figures, tables, and formulas below to determine the projection size and 
projection distance.
(Projection sizes are approximate values for full-size picture with no keystone 
adjustment.)
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all of...

Overview 24
English
Connecting to a computer
 
• Signals are outputted from Monitor OUT terminal even in standby mode. From 
AUDIO OUT terminal, no audio signal is outputted.
• Many laptops do not turn on their external video ports when connected to a 
projector. Usually a key combination like FN + F5 or CRT/LCD key turns the 
external display on/off. Locate a function key labeled CRT/LCD or a function key 
with a monitor symbol on the laptop. Press FN and the labeled function key 
simultaneously. Refer...

Overview 25
English
Connecting Video and S-Video devices
 If the selected video image is not displayed after the projector is turned on and the 
correct video source has been selected, check that the video source is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
S-Video or Video devices
S-Video cable
Audio cable Video cableor 

Operation 26
English
Operation
Start up
1. Switch all of the connected equipment on.
2. Plug the power cord into the projector and into a 
wall socket. Turn on the wall socket switch (where 
fitted). Check that the ON indicator on the 
projector lights orange after power has been 
applied.
3. Remove the lens cap. If it is left on, it could become 
deformed due to heat.
4. Press and hold the ON/STANDBY button on the 
remote control or projector to start the unit. The 
ON indicator flashes green and stays...

Operation 27
English
Adjusting the image
Adjusting the height
The projector is equipped with 1 quick-release adjuster foot and 1 tilt adjuster 
foot. The adjusters can be used to change the image height and projection angle.
To adjust the projector to your desired 
image height and projection angle:
1. Lift the projector up to the desired 
angle and press the front adjuster 
button to release the adjuster. The 
adjuster will drop into position.
2. Screw the tilt adjuster foot to fine 
tune the horizontal...

Operation 28
English
Adjusting the volume
The speaker volume can be adjusted when an audio signal is being input.
Correcting keystone
Keystone distortion refers to the situation where the projected image is noticeably 
wider at either the top or bottom. It occurs when the projector is not perpendicular 
to the screen. 
To correct this:
1. Adjust the position of the projector.
2. Press the AUTO button on the remote control or the projector.
If the image is still distorted, you will need to manually...

Operation 29
English
Shutdown
1. Press ON/STANDY and a 
confirmation prompt displays. Press 
ON/STANDY a second time to turn 
the projector off. 
2. The ON indicator flashes orange 
and the lamp shuts down. The fans 
will continue to run for approximately 
90 seconds to cool down the 
projector lamp.
• To protect the lamp, the projector will not 
respond to any commands during the 
cooling process.
• Do not unplug the power cord before the 
projector shutdown sequence is 
complete or during the 90-second...

Operation 30
English
Menu operation
Menu system
The OSD menus will vary according to the selected signal type being used. 
Functions available when receiving different 
signal types...
Sub-MenuPCVideo / S-Video / 
Component Video
 
Image adjustment 
menu
Picture mode
Keystone
Brightness
Contrast
H-position
V-position
Phase
FrequencyPicture mode
Keystone
Brightness
Contrast
Color
Tint
Sharpness
 
Display setting 
menu
Vo lu m e
OSD time
Reset all
Screen size
Aspect ratioVol u m e
OSD time
Reset all
Screen...