Toshiba Projector Tdp P7 User Manual

E-20
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-22.
1Press the SELECT 
 buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set....

E-21
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the STANDBY button.
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note:
*The operation can be cancelled by pressing a button other than the
STANDBY button.
*One more press of the STANDBY button will switch off...

E-22
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2
(2)
(1)(3)
(4)
(5)(3)(4)
Adjust the projection image to the screen.
Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted...

E-23
Adjustment of the Projection Screen
STANDBY
STATUS
MENUQUICK
MENU
SOURCE
AUTO
ECL
O
Z
(
1)
(
2)
(
1)
Note:
When the projector has a rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip” on Page E-46.
Adjuster button
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align the image...

E-24
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-33 and the various items on
Pages E-40 to E-53.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
Whenever the SOURCE button is pressed, the...

E-25
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the
input image continues to advance even though the picture there is a still
picture condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
Cancelling Video and Audio Temporarily
This function is used to cancel the video and audio at the same time.
A press of the MUTE button will blank the picture and the...

E-26
General Operation
Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video
image.
(1) Press the ZOOM button to enlarge the image.
The zoom display appears when the ZOOM button is pressed.
Each press of the 
 button enlarges the image and each press of the
 button makes the image smaller (returning it to 1:1).
(No enlargement) (Approximately 2 times enlargement)
The image can also be moved in the following circumstances.
•When “Aspect” is set...

E-27
General Operation
Using the Presentation Timer
Note:
*The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
*While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
[Timer settings display] The presentation is given while checking the timer displayed
on the screen....

E-28
General Operation
Using the Laser Pointer
The remote control unit’s laser pointer can be used to point to the section currently being explained, making presenta-
tions more effective.
Operation
The red laser beam is emitted from the tip of the remote control
unit while the LASER button is pressed in. Point the remote con-
trol unit’s transmitter in the direction you want to indicate.
The laser beam turns off when you release your finger from the
LASER button.
F
R
E
E
ZEM
U
T
EL
A
S
E
R
A
U
T
O
T
IM...

E-29
General Operation
Performing Mouse Operations on the Computer
with the Remote Control Unit
When a computer and the projector are connected, mouse operations can be performed on the computer using the
projector’s remote control unit. When projecting images from the computer, the projector can be operated and mouse
operations on the computer performed with the same remote control unit, making for efficient presentations.
Connecting the computer and projector
Use the USB cable included with the...