Toshiba Projector TDP P6 User Manual

31
Settings menuAudio: allows volume adjustments. You can also adjust volume from the 
keypad.
Sources
: allows you to assign a particular input to a specific source key 
when using certain optional remotes. Also allows selection of a default 
Power-up Source and enables or disables Autosource. When Autosource is 
not checked, the projector defaults to the source selected in Power-up 
Source. If no source is found, a blank screen displays. When Autosource is 
checked, Power-up Source determines which...

32
Screen Save: automatically blanks the screen with a black color after no sig-
nals are detected for a preset number of minutes (the default is 30 minutes). 
The image returns when an active source is detected or a remote or keypad 
button is pressed. Screen Save is disabled when Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen at startup and when no source is detected. 
Blank Screen: determines what color displays when no...

33
Language: allows you to select a language for the onscreen display of 
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default 
after displaying a confirmation dialog box.
Lamp Reset: resets the lamp hours counter in the About menu to zero after 
displaying a confirmation dialog box. Do this only after changing the lamp.
Service Code: only used by authorized service personnel.
LanguageService menu 

34
MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner 

35
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. Fifty hours before the specified end of the lamp’s life, 
the message “Change lamp” briefly appears on the screen at each startup. 
After 50 additional hours, the lamp will no longer light. You can order new 
lamp modules from your dealer.1
Turn off the projector and unplug the power cable. 
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside...

36
WARNINGS: 
 To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.
 Do not drop the lamp module. The glass may shatter and cause injury.
 Do not touch the glass lamp screen. Fingerprints can obscure projection 
sharpness.
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing...

37
AppendixAccessoriesFor assistance with this projector
For assistance with your Toshiba projector in the United States, please visit 
www.toshiba.com/tacp or contact by phone at 800-846-6672.
For assistance with your Toshiba projector in Europe, please visit 
www.toshiba-europe.com or contact your local Toshiba dealer.
For assistance with your Toshiba projector in Asia/Japan, please contact 
your local Toshiba dealer. Standard Accessories
(ship with the projector)
Shipping Box (with packaging)
Carry...

38
Red LED Behavior and Projector ErrorsIf the projector is not functioning properly and the red LED is blinking, con-
sult Ta b l e  2 to determine a possible cause. There are two second pauses 
between the blinking cycles. 
Projected image size
Table 2: 
Red LED Behavior Explanation
One (1) blink The lamp wont strike after five (5) 
attempts. Check the lamp and lamp door 
installations for loose connections.
Two (2) blinks The lamp counter hours have exceeded 
lamp life hours. Replace the lamp and...

39 A
About 32
Aspect Ratio 32
audio 24
Audio In connector 6, 11
audio volume 13
Auto Image 32
Auto Power 31BBlank 32
blinking green 14
blinking red 14
Brightness 10Ccleaning the lens 34
Color 13
colors are incorrect 20
computer connections
optional 6
required 6
Computer connector 6
computer image
optimize 25
Contrast 10, 13DDisplay Messages 31
Drivers 8
USB 9
Windows 98 9EEffect Key 32
elevator foot 10Ffirst time use
driver installation 8
focus 10, 13For 37
Freeze 32
fuzzy image 17
Iimage
display video...

40 M
Main menu 27
menu system 27
Mute 32Nno computer image 16
no startup screen 15Oonly startup screen appears 15PPicture menu 28
Power button 12
power cable 6, 11
Power Save 31
presentation features 25
projector
customizing 26
shutdown 14
standard accessories 37
troubleshooting problems 14
projector height 10, 12
projector positioning 10, 12RRear 31
remote control 23
not working 17
replacing the lamp 35
SSettings menu 31
shutdown
projector 14
solid green 14
solid red 14
Source 32
Source troubleshooting...