Toshiba Projector Tdp Et10 User Manual

21
Preparations
Preparing and using the remote control
■ Loading dry-cell batteries 
into the remote control
(1) Remove the battery cover.
(2) Insert the dry-cell batteries.
Be sure to align the plus and minus 
ends of the batteries properly.
Two batteries (R03, size AAA) are 
used.
(3) Put back the battery cover.
■  Point the remote control 
toward the projector’s 
infrared remote sensor and 
press a button.
•  Operating the projector from the front
•  Operating the projector from the rear
 Dry-cell...

22
Placement
Placement Styles
This device can be placed in some different placement styles. The factory setting is “fl oor-
mounted front projection” although you can modify the setting according to your needs. 
Set the Projection mode in accordance with your needs through remote control or control 
panel, enter SETUP menu.
Floor-mounted front projection (Standard)
Ceiling-mounted front projection (Ceiling)
TDP-ET10 only
Floor-mounted rear projection (Rear)
Ceiling-mounted rear projection (Rear Ceiling)...

23
Preparations
Screen  As seen from above
As seen from side
Lens center
Projection Distance and Size
Use the fi gures, tables, and formulas below to determine the projection size and projection 
distance. (Projection sizes are approximate values for full-size picture with no keystone 
adjustment.)
a (cm) = projection size (inches) x 1.433 – 13.32
H (cm) = projection size (inches) x 0.1868
“a” is the distance (cm) between front edge of the projector and the screen, and cor-
responds to a range of 40 cm to...

24
Connection
Before connection
•  Some types of computers cannot be used or connected to this projector.
•  Turn off the power of both devices before connecting.
•  The fi gure below is a sample connection. This does not mean that all of these devices 
can or must be connected simultaneously.
Overview of cable types:
composite video 
cable S-Video cablecomponent video 
cable HDMI cable3.5mm stereo 
audio cableVGA computer 
cable
■ Main Input
Connecting with Video/S-Video/Component
From Component
Output...

25
Preparations
Connecting with HDMI
From HDMI Output 
Te r m i n a l  ( D i g i t a l  
Audio/ Video) DVD player
Connecting with Computer
■ Notes
•  To select audio input, use On Screen menu, see p.28.
•  Signals which resolution exceeds the native resolution (854 x 480 pixels) will be compressed. For 
this reason, some information may be lost, or image quality may be affected.
• Because HDMI
TM is an evolving technology, it is possible that some devices may not operate 
properly with the projector....

26
Turning the power on and off
■ Connecting the power cord
1  Insert the power cord connector into 
the AC IN socket of the projector.
2 Insert the power cord plug into a wall 
or other power outlet.
■ Turning the power on
1  Turn on the main power switch.
The blue LED at the ON/STANDBY key will 
start to fl ash, indicating standby mode.
2 Activate the projector.
The projector can be activated by pressing the 
ON/STANDBY key on control panel for 3~5 
seconds and releasing while the red LED is 
still lit....

27
Operations
■ Using standby mode to save power and turning the power off
1   Put the Projector into standby mode to save power.
Pressing the ON/STANDBY button once, a power off indication message will appear.  
Press the ON/STANDBY button to put the projector into standby mode.  The power off 
message has to be displayed for the second press of the power button to be valid.
When cooling lamp


After cooling complete
A  The cooling fan will operate for about 60 seconds. In this state the pow\
er cannot...

28
1 Turn on the power.
Turn on the power by following the instruction in “Turning the power on” in p.26.
2 Activate the connected device.
Turn on and start the connected device.
3 Select MENU language.
This projector can display the on screen language in English, French, German, 
Spanish, Italian, Portuguese, Japanese, Traditional Chinese, Simplifi ed 
Chinese and Korean.
(1)  Press [MENU] key to display MENU.
(2)  Select SETUP icon using [UP] [DOWN] or 
  key and press .
(3)  Select ‘Language’ and press...

29
Operations
5 Projector placement angle adjustments
(1)  There are 4 adjustable feet on bottom of the 
projector.
Each foot height can be adjusted by screwing 
and the placement angle and the height of the 
projected image can be changed.
(2)  To adjust the projection size, it is needed 
to change placement closer/farther to the 
projection screen.
6 Adjusting the focus
Use focusing ring to adjust the focus.
7 Select a screen size (aspect ratio)
The aspect ratio is the ratio of image width to image...

30
8 Adjusting the volume
The speaker volume can be adjusted by pressing [-] [+] key on control panel or remote 
control.
9 Turning off the power
Turn off the power by following the instruction in “Turning the power off” in p.27.
■ Note
•  Note that a lamp characteristics may rarely cause the brightness to fl uctuate slightly.
•  A lamp is consumable item. If used for extended periods, images will appear dark, 
and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. 
(The...