Toshiba Ikwb16aw Manual

							71
Cropping Setting Advanced Mode
Click Cropping Setting  to open the Cropping Settings page.
Please follow the steps below to set up cropping mode for mutiple stream\
s:
1. Click Cropping Setting  to open the window as shown below.
2. Select a Captured area from the drop-down list. The floating frame, the same as the one in the Global 
View window on the home page, will resize accordingly. If you want to set up a customized viewing re-
gion, you can also resize and drag the floating frame to a desired position with your mouse.
3.  Click  Save  to  enable  the  settings  and  click  Close  to  exit  the  window.  Below  is  the  illustration  of 
cropped image:
cropped image   
						

							72
Video quality settings for stream 1 ~ 4 Advanced Mode
Click the items to display the detailed video quality settings. 
This  Network  Camera  offers  two  choices  of  video  compression  standards  (MPEG-4  and  JPEG)  for  real-
time viewing.
If MPEG-4  mode  is  selected,  the  video  is  streamed  via  RTSP  protocol.  There  are  four  parameters 
provided in MPEG-4 mode which allow you to adjust the video performance:
selectable
selectable
■ Frame size You  can  set  up  different  video  resolution  for  different  viewing  devices.  For  example,  set  a  smaller 
frame size and lower bit rate for remote viewing on mobile phones and a \
larger video size and a higher 
bit rate for live viewing on web browsers. Note that a larger frame size\
 takes up more bandw idth. 
■ Maximum frame rate This  limits  the  maximum  refresh  frame  rate  per  second.  Set  the  frame  rate  higher  for  smoother  video 
quality.
If  the  power  line  frequency  is  set  to  50Hz,  the  frame  rates  are  selectable  at  1fps,  2fps,  3fps,  5fps, 
8fps,  10fps,  15fps,  20fps,  and  25fps.  If  the  power  line  frequency  is  set  to  60Hz,  the  frame  rates  are 
selectable  at  1fps,  2fps,  3fps,  5fps,  8fps,  10fps,  15fps,  20fps,  25fps,  and  30fps.  You  can  also  select 
Customize and manually enter a value. The frame rate will decrease if you select a higher resolution. selectable
selectable 
						

							73
■ Intra frame periodDetermine  how  often  to  plant  an  I  frame.  The  shorter  the  duration,  the  more  likely  you  will  get  better 
video  quality,  but  at  the  cost  of  higher  network  bandwidth  consumption.  Select  the  intra  frame  period 
from the following durations: 1/4 second, 1/2 second, 1 second, 2 second\
s, 3 seconds, and 4 seconds.
■ Video quality A  complex  scene  generally  produces  a  larger  file  size,  meaning  that  higher  bandwidth  will  be  needed 
for  data  transmission.  Therefore,  if  Constant  bit  rate  is  selected,  the  bandwidth  utilization  is  fixed  at 
a  selected  level,  resulting  in  mutable  video  quality  performance.  The  bit  rates  are  selectable  at  the 
following  rates:  20Kbps,  30Kbps,  40Kbps,  50Kbps,  64Kbps,  128Kbps,  256Kbps,  512Kbps,  768Kbps, 
1Mbps, 2Mbps, 3Mbps, and 4Mbps. You can also select  Customize and manually enter a value.
On  the  other  hand,  if  Fixed  quality  is  selected,  all  frames  are  transmitted  with  the  same  quality; 
bandwidth  utilization  is  therefore  unpredictable.  The  video  quality  can  be  adjusted  to  the  following 
settings: Acceptable,  Satisfactory,  Good,  Very  Good,  and  Excellent.  You  can  also  select  Customize 
and manually enter a value from 1 (high quality) to 31 (low quality)\
.
If JPEG  mode is selected, the Network Camera continuously sends JPEG images to the client, producing 
a  moving  effect  similar  to  a  filmstrip.  Every  single  JPEG  image  transmitted  guarantees  the  same 
image  quality,  which  in  turn  comes  at  the  expense  of  variable  bandwidth  usage.  Because  the  media 
contents  are  a  combination  of  JPEG  images,  no  audio  data  is  transmitted  to  the  client.  There  are  three  
parameters provided in MJPEG mode to control the video performance:
■ Frame size You  can  set  up  different  video  resolution  for  different  viewing  devices.  For  example,  set  a  smaller 
frame size and lower bit rate for remote viewing on mobile phones and a \
larger video size and a higher 
bit rate for live viewing on web browsers. Note that a larger frame size\
 takes up more bandwidth.
■ Maximum frame rate
   This limits the maximum refresh frame rate per second. Set the frame rat\
e higher for smoother video 
   quality. If  the  power  line  frequency  is  set  to  50Hz,  the  frame  rates  are  selectable  at  1fps,  2fps,  3fps,  5fps, 
8fps,  10fps,  15fps,  20fps,  and  25fps.  If  the  power  line  frequency  is  set  to  60Hz,  the  frame  rates  are 
selectable  at  1fps,  2fps,  3fps,  5fps,  8fps,  10fps,  15fps,  20fps,  25fps,  and  30fps.  You  can  also  select 
Customize and manually enter a value. The frame rate will decrease if you select a higher resolution.
■ Video quality The video quality can be adjusted to the following settings: Acceptable, Satisfactory, Good, Very Good, 
and  Excellent.  You  can  also  select  Customize  and  manually  enter  a  value  from  10  (high  quality)  to 
200 (low quality).
● Video  quality  and  fixed  quality  refers  to  the  compression  rate,  so  a  lower  value  will  produce  higher 
quality.
NO TE 
						

							74
Audio Settings
Mute:  Select  this  option  to  disable  audio  transmission  from  the  Network  Camera  to  all  clients.  Note  that 
if mute mode is turned on, no audio data will be transmitted even if audio transmission is enabled on the 
Client Settings page. In that case, the following message is displayed:
Internal  microphone  input  gain:  Select  the  gain  of  the  internal  audio  input  according  to  ambient 
conditions. Adjust the gain from +21 db (most sensitive) ~ -33 db (least sensitive).
External  microphone  input:  Select  the  gain  of  the  external  audio  input  according  to  ambient  conditions. 
Adjust the gain from +21 db (most sensitive) or -33 db (least sensitive).
Audio type: Select audio codec AAC or GSM-AMR and the bit rate 
Advanced Mode.
■  AAC  provides  good  sound  quality  at  the  cost  of  higher  bandwidth  consumption.  The  bit  rates  are 
selectable from: 16Kbps, 32Kbps, 48Kbps, 64Kbps, 96Kbps, and 128Kbps.
■  GSM-ARM  is  designed  to  optimize  speech  quality  and  requires  less  bandwidth.  The  bit  rates  are  selectable  from:  4.75Kbps,  5.15Kbps,  5.90Kbps,  6.7Kbps,  7.4Kbps,  7.95Kbps,10.2Kbps,  and 
12.2Kbps.
When completed with the settings on this page, click  Save to enable the settings.
● The Network Camera offers two inputs to capture audio - internal microphone or external microphone. 
When external microphone is connected, it switches from internal microphone to external microphone automatically.
● The jack of microphone can use only the type of 3.5mm Stereo.
●  The  usable  microphone  is  the  Plug-in-power  Condenser  Microphones  with  3.5mm  Stereo  mini-plug. 
And right angle plug is highly recommended.
NO TE 
						

							75
Motion Detection
This  section  explains  how  to  configure  the  Network  Camera  to  enable  motion  detection. A  total 
of three motion detection windows can be configured.
Follow the steps below to enable motion detection:
Follow the steps below to enable motion detection:
1. Click New to add a new motion detection window.
2. In the Window Name text box, enter a name for the motion detection wi\
ndow.■ To move and resize the window, drag and drop your mouse on the window.
■ To delete window, click X on the top right corner of the window.
3. Define the sensitivity to moving objects and the space ratio of all alerted pixels by moving the 
    Sensitivity and Percentage slider bar.
4. Click Save to enable the settings.
5. Select Enable motion detection  to enable this function.
For example:
The  Percentage  Indicator  will  rise  or  fall  depending  on  the  variation  between  sequential  images.  When 
motions  are  detected  by  the  Network  Camera  and  are  judged  to  exceed  the  defined  threshold,  the 
red  bar  rises.  Meanwhile,  the  motion  detection  window  will  be  outlined  in  red.  Photos  or  videos  can  be 
captured instantly and configured to be sent to a remote server (Email, FTP) by utilizing this feature as a 
trigger source. For more information on how to set an event, please refer to Application on page 84.
2010/01/15 11:20:25
Video(TCP-AV)2010/01/15 16:39:26 
						

							76
A  green  bar  indicates  that  even  though  motions  have  been  detected,  the  event  has  not  been  triggered 
because the image variations still fall under the defined threshold.
● How does motion detection work?There  are  two  motion  detection  parameters:  Sensitivity  and  Percentage.  In  the  illustration  above, frame A  and  frame  B  are  two  sequential  images.  Pixel  differences  between  the  two  frames  are detected and highlighted in gray (frame C) and will be compared with the sensitivity setting. Sensitivity is a value that expresses the sensitivity to moving objects. Higher sensitivity settings are expected to detect slight movements while smaller sensitivity settings will neglect them. When the sensitivity is set to 70%, the Network Camera defines the pixels in the purple areas as “alerted pixels” (frame D).
Percentage  is  a  value  that  expresses  the  proportion  of  “alerted  pixels”  to  all  pixels  in  the  motion detection window. In this case, 50% of pixels are identified as “alerted pixels”. When the percentage is set to 30%, the motions are judged to exceed the defined threshold; therefore, the motion window will be outlined in red.
For  applications  that  require  a  high  level  of  security  management,  it  is  suggested  to  use  higher sensitivity settings and smaller percentage values.
A
B D C
NOTE    
						

							77
Camera Tampering Detection 
This  section  explains  how  to  set  up  camera  tamper  detection.  With  tamper  detection,  the 
camera is capable of detecting incidents such as redirection, blocking or defocusing, or even 
spray paint.
Please follow the steps below to set up the camera tamper detection func\
tion:
1. Check Enable camera tampering detection.
2. Enter the tamper trigger duration. (10 sec. ~ 10 min.) The tamper alarm will be triggered only when the  tampering factor (the difference between current frame and pre-saved background) exceeds the trigger 
threshold.
3.  Set  up  the  event  source  as  Camera  Tampering  Detection  on  Application  page  > Event  Settings  /
Server  Settings  (how  to  send  alarm  message)  /  Media  Settings  (send  what  type  of  alarm 
message) . Please refer to page 84 for detailed information. 
						

							78
Camera Control
This section explains how to control the Network Camera’s Pan/Tilt/digitl Zoom operation via
the control panel and how to preset positions.
Preset Positions
You can preset positions for the Network Camera to go to directly or patrol. A total of 20 preset positions 
can be configured.
Please follow the steps below to preset a position:
1. Adjust the shooting area to the desired position using the buttons on the right side of the window. 
2. Click Set as home or Default home to define your home position.
3.  Enter  a  name  for  the  preset  position,  which  allows  for  up  to  forty  characters.  Click Add  to  enable  the 
settings. The preset positions will be displayed under the Preset Location list on\
 the left-hand side.
4. To add additional preset positions, please repeat steps 1~2.
5. To remove a preset position from the list, select it from the drop-down l\
ist and click  Delete.
6.  The  preset  positions  will  also  displayed  on  the  main  page.  Please  refer  to  the  illustration  on  the  next  page.
7. Click Save to enable the settings.
Functions are the same 
as the Control Panel on 
the home page1
2
5
7
3
3 
						

							79
Home page in PTZ Mode
■ The Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected preset position. 
						

							80
Patrol Settings
You can select some preset positions for the Network Camera to patrol.
Please follow the steps below to set up a patrol schedule:
1. Click a preset location on the list and click Select.
2. The selected preset location will be displayed on the  Source list.
3. Set the  Dwelling time for the preset location during auto patrol. You can also manually enter a value 
in the blank and click  Update.
4. Repeat step 1 and 3 to select additional preset locations.
5. If you want to delete a selected location, select it from the Source \
list and click  Remove.
6. Select a location and click  Up or Down to rearrange the patrol order.
7. Adjust the Auto pan/patrol speed. 1(slow) ~5(fast)
8. Click Save to enable the settings.
right
left
up
down
rightleft
1010
10
1
2
6
5
8
3
7