Toshiba D-r400 Manual
Have a look at the manual Toshiba D-r400 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 EN41 EN Disc Management Recording Playback Introduction Connections Basic Setup Editing Function Setup Others SETTINGS FOR AN EXTERNAL DEVICE front of this unitrear of this unit IN OUT Y PR/CRPB/CBL RL RVIDEO INVIDEO OUT S-VIDEOAUDI O I N (L1)S-VIDEOAUDIO OUTCOAXIAL HDMI OUTCOMPONENT VIDEO OUTDIGITAL AUDIO OUTPUTPCM / BITSTREAM UT1080pREC PLAY STOP SKIP1080i 720p 480pDVD -RW/R +RW/R RECORDING I/yOPEN/CLOSEON/STANDBY S-VIDEO VIDEO L R DV INL2 INOUT Y PR/CR PB/CB L RL RVIDEO INVIDEO OUT S-VIDEOAU DI O I N (L1)S-VIDEOAUDIO OUTCOMPONENT VIDEO OUT AUDIO OUT DV-OUT LRVIDEO OUT S-VIDEO OUTAUDIO OUT LRVIDEO OUTS-VIDEO OUT to L1 IN external device(camcorder, VCR etc.) S-video cable RCA video cable S-video cableDV cable (4-pin) RCA video cableRCA audio cable RCA audio cable to L2 & L3 IN or or or L2L1L3 or Connection to an External Device Supplied cables used in this connection are as follows: • RCA audio cable (L/R) x 1 • RCA video cable x 1 Please purchase the rest of the necessary cables at your local store. Note • When connecting an external device of monaural output to this unit, use AUDIO L jack of L2 (Front). If you use L2 or L1 connection, make sure to select the appropriate video input type by following the steps in “SETTINGS FOR THE VIDEO INPUT” on page 19. Connect the external device properly to either L2 (front) or L1 (rear) input jacks of this unit by using S-video or RCA audio / video cables. If you are connecting a DVC (digital video camcorder), connect it to L3 (front) by using DV cable. &&6%@&/JOEC&&6%@&/JOEC
42 EN42 EN 1080pREC PLAY STOP SKIP1080i 720p 480p S-VIDEO VIDEO L R DV INL2 DVD -RW/R +RW/R RECORDING I/yOPEN/CLOSEON/STANDBY SETTINGS FOR AN EXTERNAL DEVICE Recording from an External Device 1 Turn on the TV and press [I/ yy ON/STANDBY], and be sure to select the input of the TV to which the unit is connected. 2 Press [OPEN/CLOSE A] to open the disc tray. Place the disc to record on properly. 3 Press [OPEN/CLOSE A] to close the disc tray. It takes awhile to load the disc. 4 Select the input of the unit which the external device is connected. (L1, L2 or L3) • To use the input jacks on the rear of this unit; Select “L1” by using [INPUT SELECT ]. • To use the input jacks on the front of this unit; Select “L2” or “DV“ by using [INPUT SELECT ]. 5 Press [REC MODE] to select a recording mode. Refer to “Recording Mode” on page 34. XP (1Hr)SP (2Hr)LP (4Hr)EP (6Hr)SLP (8Hr) 6 Press [REC I] on the unit to start recording. 7 Start playback on the external device to record from. 8 Press [STOP C] on the unit to stop recording. This operation may take awhile to be completed. Before recording from an external device, refer to the instructions for the connection on page 41. 8 1 OPEN/ CLOSEINPUT SELECTHDMI .@/: ABC GHI PQRS TUV SPACE SETUP DISPLAY AUDIO TOP MENU CLEAR RETURNMENU/LIST WXYZ JKL MNODEF ENTER SKIP REV PLAY REC MODE ZOOMREC REPEATPA U S E TIME SLIP 1.3x / 0.8x PLAYINSTANT SKIP STOP FWD SKIPTIMER PROG. SATELLITE LINK REC MODE REC STOP INPUT SELECTOPEN/ CLOSE GHI PQRS TUV SPACEWXYZ JKL MNO .@/: ABC DEF 23 6 &&6%@&/JOEC&&6%@&/JOEC
43 EN43 EN Disc Management Recording Playback Introduction Connections Basic Setup Editing Function Setup Others SATELLITE LINK You can set the unit to start recording whenever it detects the video signal from the external tuner. Preparing for the satellite link timer recording: Preparation on the tuner • The external tuner should be equipped with some kind of timer function. Using timer function of the tuner, set it to output audio/video signals when it comes to the time you want to start recording, and stop output audio/ video signals when it comes to the time you want to finish recording. Refer to the tuner’s manual on how to set the timer. • Make sure to set the satellite link standby mode when you finish setting. 1 Press [SATELLITE LINK]. 2 Use [K / L] to select the time and recording mode, then press [ENTER]. Satellite Link Start Mode 12:00 AM XP To Standby Mode 3 Use [K / L] or [the Number buttons] to set the desired starting time, then press [ B]. • The hour can be selected from 1 to 12 with AM or PM. • Repeat procedures in this step to set the desired minutes. • If you wish to go back to the left, press [{]. 4 Use [K / L] to select the recording mode. Refer to page 34 for details. Instructions continue on the next page. SE-R0265 OPEN/ CLOSEINPUT SELECTHDMI .@/: ABC GHI PQRS TUV SPACE SETUP DISPLAY AUDIO TOP MENU CLEAR RETURNMENU/LIST WXYZ JKL MNODEF ENTER SKIP REV PLAY REC MODE ZOOMREC REPEATPA U S E TIME SLIP 1.3x / 0.8x PLAYINSTANT SKIP STOP FWD SKIPTIMER PROG. SATELLITE LINK ENTER SATELLITE LINK &&6%@&/JOEC&&6%@&/JOEC
44 EN44 EN SATELLITE LINK 5 Press [ENTER]. “To Standby Mode” is highlighted. 6 Press [ENTER] again. Satellite Link Start Mode 12:00 AM XP To Standby Mode In a second, the unit will be turned off automatically as it goes into the satellite link standby mode. To cancel the satellite link function while in the satellite link standby mode: Press [I/ yy ON/STANDBY] to turn on the unit. To cancel the satellite link function while the satellite link recording is in progress: Press [STOP C] on the front panel of the unit. Note • If the signal of external input breaks up over 5 seconds, satellite link function will be canceled. • If you have not set the clock, “Clock Setting” menu will appear at step 1. Follow to step 3 in “CLOCK SETTING” on page 25. • You cannot set the end time for the satellite link timer recording on this unit. • Recording picture will be distorted if the copy protection signal is being detected during satellite link timer recording. • You can record the satellite link by using S-video input jacks on the rear panel. Refer to page 41 for more information. • Press [TIMER PROG.] during the satellite link timer recording to check the satellite link timer recording in progress. • When a regular timer recording and the satellite link timer recording are overlapped, those recordings are recorded as illustrated below. example 2 actual recordingtimer recording satellite link example 3 actual recordingtimer recording satellite link The first 2 minutes (at the longest) will be cut off. example 1 timer recording actual recording satellite link The first 2 minutes (at the longest) will be cut off. &&6%@&/JOEC&&6%@&/JOEC
45 EN45 EN Disc Management Recording Playback Introduction Connections Basic Setup Editing Function Setup Others DV DUBBING Guide to DV and On-Screen Display This function helps you to easily dub the contents of the DVC (digital video camcorder) to DVD. You can control basic operations of the DVC from the remote control of this unit such as playback, fast forward or reverse and stop all operations if the DVC is in video mode. Use the DV cable that has 4-pin input jack and is compliance with the IEEE1394 standards. When you connect to DV IN jack on the front of this unit, select “DV” position by using [INPUT SELECT ] on the remote control and press [DISPLAY] to show the DV dubbing information for the operating your DVC. 1. DV icon 2. Indicator of active device • When the “Control” is highlighted, press [ENTER] to display the item selection. Use [K / L] to select the device you wish to operate, then press [ENTER] to activate. • Select “DVD” to control this unit. • Select “DVC” to control your DVC. 3. Recording audio mode • Other than the DVC is in stop mode, the “DV Audio” can be selected. Press [ENTER] to display the item selection and then use [K / L] to select the audio you wish to output. Press [ENTER] again to activate. • Select “Stereo1” to dub the stereo sound. • Select “Stereo2” to dub the sound with after recording sound. • Select “Mix” to dub the stereo1 and stereo2. 4. Indicator of dubbing function • When the unit is ready for dubbing, “Start Rec” will appear. • When the unit is in dubbing, “Pause Rec” will appear. 5. Channel position • When you select “DV” by using [INPUT SELECT], “DV” will appear. DV AB-1234 0:12:34 1/ 1 1/ 1 SP 1:00 -RWVRORGControl DVD DV Audio Stereo1 Start RecDV AB-1234 0:12:34 1/ 1 1/ 1 SP 1:00 -RWVRORG 2 3 1 4 5 76 The menu changes according to what mode of DVC. Switch the mode on the DVC to playback mode for the dubbing information. When the DVC is in video mode...When the DVC is not in camera mode... 6. Product name of your DVC • If the unit cannot recognize the input signal from the DVC or the unknown product, “No Device” or “****” will appear instead. 7. Status of the current operation and the time counter Each icon means: DVC is in stop mode. DVC is in playback mode. DVC is in pause mode. DVC is fast forwarding. (standard speed) DVC is fast forwarding. (faster than above) DVC is fast forwarding. (faster than above) DVC is slow forwarding. (standard speed) DVC is slow forwarding. (faster than above) DVC is slow forwarding. (faster than above) DVC is fast forwarding. (in stop mode) DVC is fast reversing. (in stop mode) DVC is in reverse playback. DVC is fast reversing. (standard speed) DVC is fast reversing. (faster than above) DVC is fast reversing. (faster than above) DVC is in slow reverse playback. DVC is in recording. DVC is in recording pause mode. The following instructions are described with the operations using the remote control of this unit. &&6%@&/JOEC&&6%@&/JOEC
46 EN46 EN DV DUBBING DVC to DVD Dubbing Insert a recordable DVD-RW/-R or DVD+RW/+R and make sure your DVC is in video mode. 1 Use [INPUT SELECT ] to select “DV”. AB- 1234 0:00:00DV 2 Press [REC MODE] to select a recording mode. (Refer to page 34.) 3 Press [DISPLAY]. 4 Press [ENTER] to display the item selection. Use [K / L] to select “DVC”, then press [ENTER]. DV AB-1234 0:12:34 1/ 1 1/ 1 XP 1:00 -RWVRORGControl DVD DV Audio Stereo1 Start Rec Before recording from DVC, see page 41 for connection instructions. SE-R0265 OPEN/ CLOSEINPUT SELECTHDMI .@/: ABC GHI PQRS TUV SPACE SETUP DISPLAY AUDIO TOP MENU CLEAR RETURNMENU/LIST WXYZ JKL MNODEF ENTER SKIP REV PLAY REC MODE ZOOMREC REPEATPA U S E TIME SLIP 1.3x / 0.8x PLAYINSTANT SKIP STOP FWD SKIPTIMER PROG. SATELLITE LINK INPUT SELECT DISPLAY ENTER PA U S EPLAYSTOP REC MODE &&6%@&/JOEC&&6%@&/JOEC
47 EN47 EN Disc Management Recording Playback Introduction Connections Basic Setup Editing Function Setup Others DV DUBBING 5 Press [PLAY B] to find the point where you wish to start dubbing. Then, press [STOP C] where you wish to start dubbing. 6 Use [K / L] to select “Start Rec”, then press [ENTER]. The dubbing will start. 7 To stop dubbing; Use [K / L] to select “Control”, then press [ENTER]. Use [K / L] to select “DVD”, then press [ENTER]. Then press [STOP C]. Note for DV dubbing • If you press [PAUSE F] at step 5, the tape will rewind to the point a few seconds preceding the paused point when you press [ENTER] at step 6, then, it will start dubbing when it comes to the paused point. • The unit does not send out the output signal to DVC. • For the proper operation, connect DVC to the unit directly. Do not connect this unit and DVC via any other unit. • Do not connect more than 1 DVC. • The unit can only accept DVC. Other DV device such as cable/satellite box or D-VHS VCR cannot be recognized. • If no video signal is detected from the DVC during DVC to DVD dubbing, the recording will be paused and “I” will flash on the TV screen. The recording will resume when the unit detects the video signal again. • When the DVC is in camera mode, refer to “Guide to DV and On-Screen Display” on page 45. • You cannot dub from DVC during timer standby mode. • Date / time and cassette memory data will not be recorded. • Pictures with a copy-guard signal cannot be recorded. • A DV terminal is a terminal that can use the transmission mode conforming to the IEEE 1394 standards called “Fire Wire”. It serves as the interface that connects the PC and peripheral device such as “i.Link” (registered trademark of SONY). It enables digital dubbing between DV devices with little degradation. &&6%@&/JOEC&&6%@&/JOEC
48 EN48 EN INFORMATION ON PLAYBACK Structure of Disc Contents The contents of DVD are generally divided into titles, and the titles are subdivided into chapters. Audio CDs are divided into tracks. Data disc contains MP3/WMA/JPEG/DivX® are divided into folders, and the folders are subdivided into files. Title: Divided contents of a DVD video disc.Roughly corresponds to a story title in short stories. Chapter: Divided contents of a title. This corresponds to a chapter in a story. Track: Divided contents of an audio CD. Folder: Divided contents of a MP3/WMA/JPEG/DivX® data disc. Consists of number of files. Each title, chapter, track, folder or file is assigned a number, which is called “title number”, “chapter number”, “track number”, “folder number” or “file number” respectively. Some discs may not have these numbers. DVD video disc Title 1 Title 2 Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3 audio CD Track 1 Track 2 Track 3 Track 4 Track 5 MP3/WMA/JPEG/DivX® folder 1 folder 2 file 1 file 2 file 3 file 4 file 5 &&6%@&/JOEC&&6%@&/JOEC
49 EN49 EN Disc Management Recording Playback Introduction Connections Basic Setup Editing Function Setup Others BASIC PLAYBACK Direct Playback 1 Press [I/yy ON/STANDBY]. Turn on the TV and be sure to select the input to which the unit is connected. 2 Press [OPEN/CLOSE A] to open the disc tray and insert your disc with its label facing up. Align the disc to the disc tray guide. 3 Press [OPEN/CLOSE A] to close the disc tray. It may take awhile to load the disc completely. 4 Press [PLAY B] to start playback. If you are playing back a DVD-video, a menu may appear. Refer to “Using the Title/Disc Menu” on page 55. 5 Press [STOP C] once to stop playback temporarily. • Refer to “Resume Playback” on page 56. Note • Some discs may start playback automatically. SE-R0265 OPEN/ CLOSEINPUT SELECTHDMI .@/: ABC GHI PQRS TUV SPACE SETUP DISPLAY AUDIO TOP MENU CLEAR RETURNMENU/LIST WXYZ JKL MNODEF ENTER SKIP REV PLAY REC MODE ZOOMREC REPEATPA U S E TIME SLIP 1.3x / 0.8x PLAYINSTANT SKIP STOP FWD SKIPTIMER PROG. SATELLITE LINK PLAYSTOP OPEN/ CLOSE &&6%@&/JOEC&&6%@&/JOEC
50 EN50 EN BASIC PLAYBACK 1 Press [I/yy ON/STANDBY]. Turn on the TV and be sure to select the input to which the unit is connected. 2 Press [OPEN/CLOSE A] to open the disc tray and insert your disc with its label facing up. Align the disc to the disc tray guide. 3 Press [OPEN/CLOSE A] to close the disc tray. It may take awhile to load the disc completely. Title list will appear automatically. • To exit the title list, press [STOP C]. • To resume the title list, press [TOP MENU]. Note • Some discs may start playback automatically. • You can also start playback by pressing [PLAY B] instead of [ENTER] at step 5 on page 51. • At step 4, you can press [SKIP G], or press [B] when the title on the lower right of the title list is highlighted to display the next page, and press [SKIP H], or press [{] when the title on the upper left of the title list is highlighted to display the previous page. Playback from the Title List SE-R0265 OPEN/ CLOSEINPUT SELECTHDMI .@/: ABC GHI PQRS TUV SPACE SETUP DISPLAY AUDIO TOP MENU CLEAR RETURNMENU/LIST WXYZ JKL MNODEF ENTER SKIP REV PLAY REC MODE ZOOMREC REPEATPA U S E TIME SLIP 1.3x / 0.8x PLAYINSTANT SKIP STOP FWD SKIPTIMER PROG. SATELLITE LINK OPEN/ CLOSE TOP MENU ENTER SKIP SKIP STOPPLAY &&6%@&/JOEC&&6%@&/JOEC