Home > Toshiba > DVD Recorder > Toshiba D-r17dt User Manual

Toshiba D-r17dt User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba D-r17dt User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							21EN
    IntroductionConnectionsBasic Setup Playback
    EditingOthers Function Setup
    Recording
    Note
    • Because HDMI is an evolving technology, it is 
    possible that some devices with an HDMI input may 
    not operate properly with this unit.
    • When using an HDCP-incompatible display device, 
    the image will not be viewed properly.
    • Among the devices that support HDMI, some 
    devices can control other devices via the HDMI 
    connector; however, this unit cannot be controlled 
    by another device vice the HDMI connector.
    • The audio signals from the HDMI connector 
    (including the sampling frequency, the number of 
    channels and bit length) maybe limited by the device 
    that is connected.
    • Among the monitors that support HDMI, some do 
    not support audio output (for example, projectors). 
    In connections with device such as this unit, audio 
    signals are not output from the HDMI output 
    connector.
    • When this unit’s HDMI connector is connected to a 
    DVI-D compatible monitor (HDCP compatible) with 
    an HDMI-DVI converter cable, the signals are output 
    in digital RGB.
    • If the connected equipment is not compatible with 
    HDMI BITSTREAM, DTS sound will not be output.
    • When the power failure occurs, or when you unplug 
    the unit, some problems in the HDMI setting might 
    occur.
    Please check and set the HDMI setting again.Connecting to External Equipment
    This unit has three input terminals, AV1 or AV2 on the 
    rear panel and AV3 on the front panel. Be sure that all 
    the units are off before making connections.
    Recording from a DVD player, Satellite Box 
    or other Audio-Video equipment with a Scart 
    output socket (AV2)
    Note
    • When you record a TV programme from a Satellite 
    Box, you must connect a Scart cable to 
    AV2(DECODER). (See page 42.)
    • When AV2 is connected, the signal from the AV2 will 
    be output automatically. If you want to monitor the 
    signal from other input, you must press [DISPLAY] 
    first. Then, select the desired input to monitor with 
    [INPUT SELECT  ].
    Recording from a camcorder or other 
    Audio-Video equipment with no Scart output 
    socket (AV3)
    If no S-Video input  jack is available, connect to 
    VIDEO input jack on the front panel using an RCA 
    Video cable.
    Change the setup when using S-VIDEO input jack. 
    (See page 44.)
    AV 2(
    DECODER)
    AV 1(
    TV)ANALOG
    AUDIO OUTCOMPONENT
    VIDEO OUTPUTANALOG DVB-TOUTINANTENNA
    PB/CBPR/CR
    YL
    RCOAXIALDIGITAL AUDIO OUTPUT
    PCM/BITSTREAMHDMI OUT
    AV output jack 
    (Scart)
    Scart cable (not supplied)
    AV2 (DECODER)
    1080pREC PLAY STOP1080i 720p 576p/480p
    S-VIDEO VIDEO L RAV 3
    AV 3  ( F r o n t )
    S-Video cable 
    (not supplied)Audio cable 
    (not supplied)
    S-VIDEO 
    OUTAUDIO
    OUT
    E7J70BD_EN.book  Page 21  Monday, May 7, 2007  3:31 PM 
    						
    							22EN
    Digital Audio for Better Sound Quality 
    The connections illustrated above are 
    optional for better sound.
    1For clear digital sound quality, use 
    the DIGITAL AUDIO OUTPUT 
    (COAXIAL) jack to connect your 
    digital audio equipment.
    If the audio format of the digital output does not 
    match the capabilities of your receiver, the 
    receiver will produce a strong, distorted sound or 
    no sound at all.
    Connecting a Dolby Digital™ decoder, DTS 
    decoder or MPEG decoder
    • Connecting multi-channel Dolby Digital decoder 
    allows you to enjoy the Multi-channel Dolby Digital 
    surround system as well as DTS decoder, Multi-
    channel surround system.
    • After connecting to a Dolby Digital decoder, set 
    “Dolby Digital” to “Stream” in the Audio out menu. 
    (See page 72.)   
    • After connecting to a DTS decoder, set “DTS” to 
    “ON” in the Audio out menu. (See page 72.)  
    • After connecting to a MPEG decoder, set “MPEG” to 
    “Stream” in the Audio out menu. (See page 72.)    
    Connecting to an MD deck or DAT deck
    • The audio source recorded in Dolby Digital Multi-
    channel surround format cannot be recorded using 
    an MD or DAT deck as a digital sound.
    • If not connected to a Dolby Digital decoder, set 
    “Dolby Digital” to “PCM” in the Audio out menu. 
    Playing back a DVD using incorrect settings may 
    generate noise distortion and damage speakers.
    • Set “Dolby Digital” and “MPEG” to “PCM” and set 
    “DTS” to “OFF” in the Audio out menu for connecting 
    to an MD or DAT deck.
    • You can use ANALOG AUDIO OUT jacks for the 
    connection of your audio system.
    After You Have Completed 
    Connections
    Switch the input selector on your TV to an appropriate 
    external input channel. For details, refer to the 
    Owner’s Manual of your TV.
    Note
    • Connect this unit directly to the TV. If the AV cables 
    are connected to a VCR, pictures may be distorted 
    due to the effects of the copy protection system.
    AV 2(
    DECODER)
    AV 1(
    TV)ANALOG
    AUDIO OUTCOMPONENT
    VIDEO OUTPUTANALOG DVB-TOUTINANTENNA
    PB/CBPR/CR
    YL
    RCOAXIALDIGITAL AUDIO OUTPUT
    PCM/BITSTREAMHDMI OUT
    COAXIAL
    COAXIALDIGITAL AUDIO OUTPUT
    PCM/BITSTREAM
    Dolby Digital decoder,
    DTS decoder or
    MPEG decoder, etc.Digital audio
    input jacks
    Coaxial cable 
    (not supplied)
    E7J70BD_EN.book  Page 22  Monday, May 7, 2007  3:31 PM 
    						
    							23EN
    Introduction ConnectionsBasic SetupPlayback
    EditingOthers Function Setup
    Recording
    Initial Setting
    Turn on this unit for the first time, you need to follow 
    these steps.
    1Press [ ON / STANDBY].
    2Turn the TV on. Select the input to 
    which the unit is connected.
    3Select your desired channel preset 
    type using [U / D]. Then press 
    [ENTER/OK].
    The unit will start getting channels available in 
    your area.
    Digital tuning:
    Only the DVB channels receivable in your area 
    are automatically scanned and memorised.
    Digital & Analog tuning:
    Both analogue and DVB channels receivable in 
    your area are scanned and memorised 
    automatically. 
    Analog tuning:
    Only the analogue channels receivable in your 
    area are automatically scanned and memorised.
    4After finished channel setting, 
    “Clock Setting” will appear. Then 
    press [ENTER/OK].
    • If you want to adjust the clock, follow to step 4 
    on page 31 in “Manual Clock Setting”.
    5Press [ENTER/OK] to exit.
    Channel Setting
    Tuning of this unit to broadcast channels can be 
    performed in two ways.
    Auto Tuning (DVB & ANALOG)
    Programme the tuner to scan both analogue and DVB 
    channels you can receive in your area.
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U / D], 
    then press [ENTER/OK].
    General Setting Menu will appear.
    2Select “Channel” using [U / D], then 
    press [ENTER/OK].
    3Select “Auto Tuning (DVB & 
    ANALOG)” using [U / D], then press 
    [ENTER/OK].
    The unit will start storing channels available in 
    your area.
    Wait for several minutes to finish channel storing.
    • Analogue channels will be stored in channel 
    901-999 after it is scanned by this unit.
    4Press [SETUP] to exit.
    You can select the channels memorised only in 
    this unit by using [PROG.  / ].
    To cancel auto tuning
    Press [RETURN/BACK] or [SETUP] during scanning.
    Note
    • The selection will be affected by how you receive TV 
    channels in your local area.
    • If the auto tuning is cancelled during scanning, 
    some channels not yet tuned may not be received.
    • You cannot change the channel when DVD is in any 
    recording mode (normal recording, One-touch Timer 
    Recording or timer recording).
    Basic Setup
    Initial Setting
    Auto Tuning
    Make sure the antenna is 
    connected to “ANTENNA IN” jack.
    Digital tuning
    Digital & Analog tuning
    Analog tuning
    Initial Setting
    Clock Setting01 / 01 / 2007 (MON)
    10:00
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    Channel
    DivX
    HDMI
    Reset All
    Auto Tuning (DVB & ANALOG)DVB Channel Setup
    ANALOG Channel Setup
    E7J70BD_EN.book  Page 23  Monday, May 7, 2007  3:31 PM 
    						
    							24EN
    Auto Tuning (ANALOG)
    Programme the tuner to scan only the channels you 
    can receive in your area.
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U / D], 
    then press [ENTER/OK].
    General Setting Menu will appear.
    2Select “Channel” using [U / D], then 
    press [ENTER/OK].
    3Select “ANALOG Channel Setup” 
    using [U / D], then press 
    [ENTER/OK].
    4Select “Auto Tuning” using [U / D], 
    then press [ENTER/OK].
    The unit will start storing channels available in 
    your area.
    Wait for several minutes to finish channel storing.
    • Analogue channels will be stored in channel 
    901-999 after it is scanned by this unit.
    5Press [SETUP] to exit.
    You can select only the channels memorised in 
    this unit by using [PROG.  / ].
    To cancel auto tuning
    Press [RETURN/BACK] or [SETUP] during scanning.
    Note
    • The selection will be affected by how you receive TV 
    channels in your local area.
    • If the auto tuning is cancelled during scanning, 
    some channels not yet tuned may not be received.
    • You cannot change the channel when DVD is in any 
    recording mode (normal recording, One-touch Timer 
    Recording or timer recording).
    Manual Tuning (ANALOG)
    You can preset an analogue channel manually and 
    individually.
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U / D], 
    then press [ENTER/OK].
    2Select “Channel” using [U / D], then 
    press [ENTER/OK].
    3Select “ANALOG Channel Setup” 
    using [U / D], then press 
    [ENTER/OK].
    4Select “Manual Tuning” using 
    [U / D], then press [ENTER/OK].
    5Select “Position” using [U / D], then 
    press [P].
    6Select the position number you wish 
    to use using [the Number buttons] or  
    [U / D], then press [L].
    • You can select position number 901-999.
    •With [the Number buttons], you only need to 
    enter the last 2 digit numbers. 
    7Select “Channel” using [U / D], then 
    press [P].
    8Press [U / D] to start scanning.
    • The tuner will begin to search up or down 
    automatically. When a channel is found, the unit 
    will stop searching and the picture will appear 
    on the TV screen.
    • You can select a desired channel number using 
    [the Number buttons]. Refer to the following 
    Channel Plan table and press the three digits to 
    select the channel number.
    (To select channel 4, press [0] first and then 
    press [0] and [4]. Or press [4] and then “– – 4” 
    appears and wait for 2 seconds.)
    • If this is the channel you want, press [L]. ANALOG
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    Channel
    DivX
    HDMI
    Reset All
    Auto Tuning (DVB & ANALOG)DVB Channel Setup
    ANALOG Channel SetupANALOG Channel Setup
    Auto Tuning
    Manual Tuning
    Move
    ANALOG
    Channel Plan
    CH Indication TV Channel
    01 – 10 IRA-IRJ, GAP
    21 – 69 E21 – E69
    74 – 78 X, Y, Z, Z+1, Z+2
    80 – 99, 100 S1 – S20, GAP
    121 – 141 S21 – S41
    Manual Tuning
    Channel
    Decoder
    SkipPosition
    1
    OFF
    ON 901
    E7J70BD_EN.book  Page 24  Monday, May 7, 2007  3:31 PM 
    						
    							25EN
    Introduction ConnectionsBasic SetupPlayback
    EditingOthers Function Setup
    RecordingThis unit can receive the Hyper and Oscar 
    frequency bands.
    • If “Skip” is set to “ON”, select “Skip” using 
    [U / D], then press [P]. Select “OFF” using 
    [U / D], then press [L].
    • If you want to decode scrambled signals, select 
    “Decoder” using [U / D], then press [P]. Select 
    “ON” using [U / D], then press [L].
    • To store another channel, repeat steps 5 to 8.
    9After completion, press [SETUP] to 
    exit.
    To Skip a Preset Channel
    You can set the unit to skip channels you can no 
    longer receive or seldom watch when you access 
    channels using [PROG.  / ].
    1Follow steps 1 to 4 in “Manual 
    Tuning (ANALOG)” on page 24.
    2Select “Position” using [U / D], then 
    press [P].
    3Select the position number you wish 
    to skip using [the Number buttons] 
    or [U / D], then press [L].
    4Select “Skip” using [U / D], then 
    press [P].
    5Select “ON” using [U / D], then 
    press [L].
    • To skip another channel, repeat steps 2 to 5.
    6Press [SETUP] to exit.
    Move
    You can replace two channels.
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U / D], 
    then press [ENTER/OK].
    2Select “Channel” using [U / D], then 
    press [ENTER/OK].
    3Select “ANALOG Channel Setup” 
    using [U / D], then press 
    [ENTER/OK].
    4Select “Move” using [U / D], then 
    press [ENTER/OK].
    5Select the position number of which 
    you want to change the channel 
    using [U / D], then press 
    [ENTER/OK].
    You cannot select a position number where 
    “– – –” appears next to the number, because 
    “Skip” is set to “ON” for that position number.
    6Move the channel to another 
    position number using [U / D], then 
    press [ENTER/OK].
    • To move another channel, repeat steps 4 to 6.
    7Press [SETUP] to exit.
    Auto Tuning (DVB)
    You can programme the tuner to scan only the DVB 
    channels that you can receive in your area.
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U / D], 
    then press [ENTER/OK].
    General Setting Menu will appear.
    2Select “Channel” using [U / D], then 
    press [ENTER/OK].
    3Select “DVB Channel Setup” using 
    [U / D], then press [ENTER/OK].
    4Select “Auto Tuning” using [U / D], 
    then press [ENTER/OK].
    The unit will start storing channels available in 
    your area.
    The tuner scans and memorise all the active DVB 
    channels in your area. 
    •Press [GREEN] after Auto Tuning is completed, 
    then the lowest memorised DVB channel 
    appears on the screen, and you can use 
    [PROG.  / ] for the memorised DVB 
    channels.
    • If you press [RETURN/BACK] or [RED] during 
    the scanning, the screen will return to the 
    previously displayed menu, and Auto Tuning will 
    be cancelled.
    • If you press [SETUP] during the scanning, this 
    operation will stop and the lowest memorised 
    DVB channel will appear on the TV screen. ANALOG
    ANALOG
    DVB
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    Channel
    DivX
    HDMI
    Reset All
    Auto Tuning (DVB & ANALOG)DVB Channel Setup
    ANALOG Channel SetupDVB Channel Setup
    Edit Channels
    Auto Tuning
    Manual Tuning
    Signal Information
    CHANNEL SEARCH
    CHANNEL  22 – 482 MHz
    TV  13 RADIO  0
    Channel1
    Channel2
    Channel3
    Channel4
    Channel5
    Channel6
    Channel7
    Channel8
    BACK
    E7J70BD_EN.book  Page 25  Monday, May 7, 2007  3:31 PM 
    						
    							26EN
    Manual Tuning (DVB)
    You can preset a DVB channel manually and 
    individually.
    1Follow steps 1 to 3 in “Auto Tuning 
    (DVB)” on page 25.
    2Select “Manual Tuning” using 
    [U  / D ], then press [ENTER/OK].
    3Select your desired position number 
    using [U  / D ], then press 
    [ENTER/OK].
    • The tuner will begin to search up or down  automatically. When a DVB channel is found, 
    the unit will stop searching.
     When “Auto” is selected the unit will search for  the channels which have not been stored in 
    channels memory. 
    4Press [GREEN] to activate the 
    setting.
    To Select a Channel
    You can select memorised channels by using 
    [PROG.  / ] . For DVB channels you can use the 
    favourite lists (TV1-TV4) to loop channels only within 
    the favourite list. (See “TV Title List” on page 27.)   
    You can select a channel using  [PROG.  / ], or 
    directly enter the channel using  [the Number 
    buttons] on the remote control.
    Notes on using [the Number buttons]:
     For one or two digit number channels, the channels 
    will be identified 2 seconds after you press the 
    channel number, or right after you press 
    [ENTER/OK] . For example, if you want to select 
    channel 6, press  [6] and wait for 2 seconds or press 
    [ENTER/OK] . You can only select channels 1 to 
    999.
     Analogue channels will be stored in channel 901- 999 and DVB channels will be stored in channel 1-
    900 after it is scanned by this unit. To switch DVB, analogue and external input (AV1/
    AV 2 / AV 3 )  m o d e .
    You can switch between DVB, analogue and external 
    input (AV1/AV2/AV3) mode by pressing [INPUT 
    SELECT ] repeatedly. The mode changes as 
    follows:
     You can also switch the mode by using 
    [PROG.  / ] .
     You cannot select any DVB channels using  [the Number buttons]  when you are in analogue or 
    external input (AV1/AV2/AV3) mode.
     You cannot select any analogue channels using  [the Number buttons]  when you are in DVB mode.
    Edit Channels
    With the EDIT CHANNELS screen, you can see all 
    memorised DVB channels, create favourite lists, and 
    set the viewer limitation to channels (Adult lock).
    To display EDIT CHANNELS screen, after following 
    steps 1 to 3 in “Auto Tuning (DVB)” select “Edit 
    Channels” using [U / D ], then press  [ENTER/OK] .
    Guide to EDIT CHANNELS screen
    1 Channel numbers.
    2 Appears when the channel is locked for the 
    Adult Lock.
    3 Channel names.
    4 Type of displayed TV title list.
    5 Indicates the registered favourite list number 
    for the channels.
    The EDIT CHANNELS screen consist of list of the all 
    memorised DVB channels (TV LIST), and four 
    favourite lists (TV1 - TV4). You can switch between 
    those channels by pressing  [GREEN] repeatedly.
     If the favourite list does not have any channels, the  list will be skipped.
     If there are more than one page of the CH List (TV  List) or the favourite list (TV1 -TV4), you can turn the 
    pages by using  [L  / P ].
    Note
     You cannot select “Edit Channels” when you are in 
    analogue, or external input (AV1/AV2/AV3) mode.
     If you execute the Auto Tuning for DVB channels,  the setting in the EDIT  CHANNELS screen will be 
    cleared.
    DVB
    Manual Tuning (DVB)
    Channel
    Auto
    DVB modeAnalogue modeAV 1AV 2AV 3
    EDIT CHANNELS
    # NAME 1 2 3 4
    12 4
    13
    1 23
    1
    1 Channel1
    2 Channel2
    3 L Channel3
    Channel4
    5 Channel5
    6 L Channel6
    7 Channel7
    8 Channel8
    TV LIST
    ADULT LOCK
    1
    2354
    CH List
    (TV List)Favourite  
    List
    (TV 1)Favourite  
    List
    (TV 2)Favourite  
    List
    (TV 3)Favourite  
    List
    (TV 4)
    23_31_BasicSetup_EN.fm  Page 26  Tuesday, July 17, 2007  1:14 PM 
    						
    							27EN
    Introduction ConnectionsBasic SetupPlayback
    EditingOthers Function Setup
    Recording
    TV Title List
    You can create 4 different favourite lists (TV1 - TV4) 
    with your preferred DVB channels and radio stations. 
    By setting the certain favourite list, you can loop 
    channels only within the list when you use 
    [PROG.  / ].
    1Follow steps 1 to 3 in “Auto Tuning 
    (DVB)” on page 25.
    2Select “Edit Channels” using 
    [U / D], then press [ENTER/OK].
    3Select the DVB channel you want to 
    add to the favourite list using 
    [U / D], then select the number of 
    the favourite list you want to add to 
    using [the Number buttons] (1, 2, 3, 
    or 4).
    • To add another channels to the favourite list, 
    repeat steps 3.
    To delete from the favourite lists:
    • Select the DVB channels you want to delete 
    from the favourite lists using [U / D] then select 
    the number of the favourite list you want to 
    delete from using [the Number buttons] (1, 2, 
    3 or 4).
    4Press [SETUP] or [RETURN/BACK] 
    to exit.
    To set the favourite lists:
    • At the step 3, press [GREEN] repeatedly to 
    select the list you want to set, then press 
    [SETUP] or [RETURN/BACK] to exit.
    Note
    • Empty favourite lists will be skipped when you 
    switch between the lists by pressing [GREEN].
    Changing the Channel Order of the 
    Favourite List
    You can change the order of the channels in favourite 
    list. 
    1Follow the steps 1 to 2 in the “TV 
    Title List”.
    2Select a favourite list (TV1-TV4) by 
    pressing [GREEN] repeatedly.
    3Select the DVB channel you want to 
    move using [U / D], then press 
    [YELLOW].
    4Select the position you want to move 
    the channel to using [U / D], then 
    press [YELLOW].
    • To move another channel, repeat steps 3 to 4.
    5Press [SETUP] to exit.
    Note
    • This function is available for only favourite lists 
    (TV1-TV4).
    Adult Lock
    You can select DVB channels and radio stations to 
    prevent access to it.
    1Follow steps 1 to 3 in “Auto Tuning 
    (DVB)” on page 25.
    2Select “Edit Channels” using 
    [U / D], then press [ENTER/OK].
    3Select the DVB channel you want to 
    limit the access to using [U / D], 
    then press [BLUE].
    • “L” is displayed on the left side of the channel 
    name when the channel is locked.
    • To unlock the channel, select locked channel, 
    then press [BLUE].
    4Press [SETUP] to exit.
    • After you turn off the unit once, a PINCODE will 
    be required to view the channels.
    • To set the PINCODE, refer to “PINCODE Setting 
    for Adult Lock” on page 29.
    Signal Information 
    You can check the detailed information of the current 
    DVB channel.
    1Follow steps 1 to 3 in “Auto Tuning 
    (DVB)” on page 25.
    2Select “Signal Information” using 
    [U / D], then press [ENTER/OK].
    • Signal Information display will appear.
    3Press [SETUP] to exit.
    Note
    • “Signal Information” is not available for analogue 
    channel and external input (AV1/AV2/AV3).
    • “Signal Information” is also not available while the 
    PINCODE input field for locked DVB channel is 
    displayed. DVB
    DVB
    EDIT CHANNELS
    #    NAME  1 2 3 4
    1 2   4
    1   3 
    1 1   Channel1
    2   Channel2
    3   Channel3
    TV1
    ADULT LOCK
    DVB
    DVB
    SIGNAL INFORMATION
    CHANNEL Channel1
    NETWORK NAME NETWORK1
    FREQUENCY CHANNEL 22, 428.000MHz
    SYMBOL RATE 8K 64QAM R2/3 G1/32
    BIT ERROR RATE < E-8
    SERVICE ID 8261 VIDEO PID 520
    AUDIO PID 521
    QUALITY 85%
    SIGNAL STRENGTH 40%
    E7J70BD_EN.book  Page 27  Monday, May 7, 2007  3:31 PM 
    						
    							28EN
    TV View Operation
    The following operations are available while viewing 
    TV channels through this unit’s tuner.
    Selecting the Audio Mode
    You can switch between TV audio modes by pressing 
    [AUDIO ]  on the remote control. Each mode is 
    indicated on the TV screen.
     During reception of analogue bilingual broadcasts
     During the reception of DVB broadcast, when you 
    press  [AUDIO ] , sound track display will appear. 
    Press  [AUDIO ]  repeatedly to change the sound 
    track. 
     If the programme does not have more than one  sound track,  [AUDIO ]  is not effective.
    Selecting the TV Aspect Ratio
    You can select the TV aspect ratio to match the format 
    of the programme you are playing back with the unit 
    and that of your TV screen (4:3 standard or 16:9 wide 
    screen TV).
    1In stop mode, press [SETUP]. Select 
    “General Setting” using [U  / D ], 
    then press [ENTER/OK].
    2Select “Video” using [ U / D ], then 
    press [ENTER/OK].
    3Select “TV Aspect” using [ U / D ], 
    then press [ENTER/OK].
    4Select the desired option using 
    [ U  / D ], then press [ENTER/OK].
    5Press [SETUP] to exit.
    Hint
    If you have a standard TV:
     Select “4:3 Letter Box”  for a full width picture 
    with black bars at the top and bottom.
     Select “4:3 Pan & Scan”  for a full height picture 
    with both sides trimmed.
    If you have a wide screen TV:  Select “16:9 Wide”.
    Digital Teletext Reception
    Many broadcasters provide a DVB Teletext service in 
    the form of a dedicated Teletext channel. This Digital 
    service includes high quality text and graphics along 
    with advanced navigation options.
     Make sure “Service Preference” is set to “Data 
    Service”. (See page 30.)
    1Press [TEXT] to display Teletext 
    screen. 
     Teletext for the TV channel you have selected will be displayed.
    2Use [RED] / [GREEN] / [YELLOW] / 
    [BLUE] to follow the instructions on 
    screen.
    3Press [TEXT] to switch the Teletext 
    display off.
    Note
     To use DVB Teletext, you must set “Service  Preference” to “Data Service”. (See page 30.)
     To set the Teletext language, refer to “Language 
    Setting” on page 30.
    ModeAudio outputDisplay on the  TV screen
    Main Main audio from both 
    speakers Main
    Sub Sub audio from both 
    speakers
    Sub
    Main / Sub  Main audio from the left 
    speaker
     Sub audio from the  right speaker Main / Sub
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    Channel
    DivX
    HDMI
    Reset All TV Aspect
    Select Video
    Video Out
    DVB
    HDMI
    Reset All
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    Channel
    DivXTV Aspect
    Select Video
    Video Out
    TV Aspect4:3 Letter Box
    4:3 Pan & Scan
    16:9 Wide
    23_31_BasicSetup_EN.fm  Page 28  Friday, July 13, 2007  5:24 PM 
    						
    							29EN
    Introduction ConnectionsBasic SetupPlayback
    EditingOthers Function Setup
    Recording
    EPG (Electronic Programme Guide)
    Electronic programme guide (EPG) gives you a list of 
    DVB programmes and detailed information about the 
    programmes. To call up EPG (Electronic Programme 
    Guide), while viewing DVB/analogue channel or 
    external input (AV1/AV2/AV3), press [GUIDE].
    You can also call up EPG by following steps.
    1In stop mode, press [SETUP]. Select 
    “Timer Programming” using [U / D], 
    then press [ENTER/OK]. 
    2Select “EPG” using [U / D], then 
    press [ENTER/OK].
    • Select the TV programme using [U / D], then press 
    the [ENTER/OK] to watch the selected channel or 
    press [BLUE] to display time schedule of the DVB 
    channel.
    • From the EPG screen, you can also set the timer 
    recording. Refer to “Timer Recording (EPG)” on 
    page 42.
    Subtitle
    Many DVB channels transmit Subtitle information 
    along with their DVB channels. With this unit, you can 
    retrieve and display it on the screen.
    • Make sure “Service Preference” is set to “Subtitle”. 
    (See page 30.)
    1While viewing DVB channels, press 
    [DISPLAY].
    2Select the   icon using [L / P], 
    then press [ENTER/OK] within 1 
    second, or wait for 1 second to 
    display the selection menu.
    3Select “On” using [U / D], then 
    press [ENTER/OK].
    Subtitle will be displayed, and if you select “Off” 
    the subtitle will disappear.
    Note
    • To use subtitle, you must set “Service 
    Preference” to “Subtitle”. (See page 30.)
    • To set the subtitle language, refer to “Language 
    Setting” on page 30.
    DVB Menu Setting
    You can make settings of the digital tuner from the 
    DVB Menu.
    PINCODE Setting for Adult Lock
    You can select Adult Lock ON or OFF and also 
    change PINCODE.
    1In stop mode, press [SETUP].
    2Select “DVB Menu” using [U / D], 
    then press [ENTER/OK].
    3Select “Adult Lock” using [U / D], 
    then press [ENTER/OK].
    4Select “ON” or “OFF” using [U / D], 
    then press [ENTER/OK].
    5To set the Adult Lock ON: 
    1) Enter your desired PINCODE using 
    [the Number buttons], then press 
    [ENTER/OK].
    2) For confirmation, enter the PINCODE again 
    using [the Number buttons].
    To set the Adult Lock OFF:Enter the PINCODE using 
    [the Number buttons].
    • While entering the PINCODE, use [L] or 
    [CLEAR] to clear the numbers once entered. 
    6Press [SETUP] to exit.
    Note
    • Once the Adult Lock has been set to “ON”, 
    PINCODE will be required in order to view or timer 
    recording the locked channels, and to execute the 
    “Auto Tuning” for DVB or “Edit Channels”.  
    • If you forgot the PINCODE, press [4], [7], [3], [7], to 
    cancel the PINCODE. DVB
    DVB
    DVB
    DVB Menu
    Language
    Service Preference
    Reset All About Adult Lock
    E7J70BD_EN.book  Page 29  Monday, May 7, 2007  3:31 PM 
    						
    							30EN
    Language Setting
    1Follow steps 1 to 2 in “PINCODE 
    Setting for Adult Lock” on page 29.
    2Select “Language” using [U / D ], 
    then press [ENTER/OK].
    3Select the item you want to change 
    the language using [U  / D], then 
    press [ENTER/OK].
    Audio : Set the Audio language
    Subtitle : Set the Subtitle language
    Data Service: Set the Digital Teletext language
    4Select a language using [ U / D ], 
    then press [ENTER/OK].
    5Press [SETUP] to exit.
    Note
    • You can also change the audio language using  [AUDIO ]  if it is available.
     The Audio, Subtitle and Digital Teletext language  setting may not be available for some broadcast.
    Service Preference Setting
    Set whether you receive the Teletext or Subtitle 
    information from the DVB. 
    1Follow steps 1 to 2 in “PINCODE 
    Setting for Adult Lock” on page 29.
    2Select “Service Preference” using 
    [U  / D ], then press [ENTER/OK].
    3Select a desired information to 
    receive using [ U / D ], then press 
    [ENTER/OK].
    4Press [SETUP] to exit.
    Note
     This unit supports MHEG5 data service.
     This unit does not support MHP data service.
    About
    You can check the current DVB system software 
    version of this unit.
    1Follow steps 1 to 2 in “PINCODE 
    Setting for Adult Lock” on page 29.
    2Select “About” using [U  / D ], then 
    press [ENTER/OK].
    3Press [SETUP] to exit.
    Note
     Whenever a new software is available, it is  advisable to always accept and download the 
    software. In case new software is available, you will 
    see a message when you switch on the DVB 
    channel.
    Resetting the DVB  Menu Setting to 
    Default
    1Follow steps 1 to 2 in “PINCODE 
    Setting for Adult Lock” on page 29
    2Select “Reset All” using [ U / D ], 
    then press [ENTER/OK].
    3Select “Yes” using [ U / D ], then 
    press [ENTER/OK].
    “Are you sure?” will appear. Select “Yes” using 
    [ U  / D ], and then press  [ENTER/OK].
    4Press [SETUP] to exit.
    Note
     The PINCODE for Adult Lock will remain unchanged 
    even after resetting the DVB Menu setting to default.
    DVB
    DVB
    DVB Menu
    Language
    Service Preference
    Reset All About Adult LockAudio
    Subtitle
    Data Service
    DVB
    DVB
    UPDATE
    NO
    YES
    YOUR CURRENT SOFTWARE IS VERSION
    1.00. VERSION 2.00 IS AVAILABLE FOR
    UPDATE. UPDATING IS RECOMMENDED.
    DO YOU WISH TO UPDATE?
    DVB Menu
    Language
    Service Preference
    Reset All About Adult Lock
    Reset to factory default? Ye sNo
    23_31_BasicSetup_EN.fm  Page 30  Tuesday, July 17, 2007  1:13 PM 
    						
    All Toshiba manuals Comments (0)

    Related Manuals for Toshiba D-r17dt User Manual