Tone Commander 7210, 7220 Ip Centrex Telephone Network Administration Guide

13-102865  Rev. K
April  2003
7210 / 7220
IP Centrex Telephone
Network Administration Guide 

© 2003, Tone Commander Systems, Inc.  All rights reserved.
Printed in USA
Tone Commander is a registered trademark of Tone Commander Systems, Inc.
Windows and Windows NT are registered trademarks of Microsoft Corp.
This document applies to telephone software version 01.02.18. 

Tone Commander 7210/7220 Network Administration Guide
13-102865  Rev. KPage 3 of 32
Contents  _____________________________________
Overview ......................................................................................................................................4
DHCP Server Configuration .......................................................................................................4
Windows 2000 Server...

Page 4 of 3213-102865  Rev. K
Overview  _____________________________________
This manual is intended for use by network administrators.
Each telephone on the network must be assigned a unique IP address. The address can be assigned
automatically by a DHCP server, or entered manually at the phone.
Telephone operating software can be updated from a TFTP server. The update process can be initiated
manually at the phone, or set to occur daily at a preset time. Operating software is automatically updated...

Tone Commander 7210/7220 Network Administration Guide
13-102865  Rev. KPage 5 of 32
  3.  Click Next to show the Scope Name screen.
  4.  Enter a name and description for the scope.
  5.  Enter the start and end of the IP address range
that can be assigned to telephones.
  6.  Enter the appropriate subnet mask. 

Page 6 of 3213-102865  Rev. K
  7.  If you need to exclude some IP addresses from
the range, enter them here, otherwise click Next.
  8.  You can use the defaults, or enter a new lease
duration for telephone IP addresses. Lease
duration should be set to 7 days or longer.
  9. Select Yes on the Configure IP Options screen.
When the lease expires the phone
shows a diagnostic display if idle,
while attempting to negotiate a new IP
address lease at preset intervals. If
the phone is active, the call will be...

Tone Commander 7210/7220 Network Administration Guide
13-102865  Rev. KPage 7 of 32
  10.  Enter the IP address of the router or default
gateway.
  11.  If needed, enter the parent domain name, DNS
servers, and WINS servers on the next two
screens.
  12. Select Yes to activate this scope.
  13. Click Finish on the next screen.
Scope Options
  1.  In the Tree pane, expand (double-click or ‘+’) the
VoIP DHCP server.
  2.  Expand the Scope entry for the telephone IP
address range.
  3. Right-click Scope...

Page 8 of 3213-102865  Rev. K
  4.  Check the box next to 002 Time Offset.
  5. Select 002 Time Offset. If your network time
server is set to UTC time, enter the hex value for
your locations offset from UTC time in seconds. If
your network time server is set to local time, enter
0.
Time ZoneOffset
Pacific Standard Time 0xffff8f80
Pacific Daylight Time 0xffff9d90
Mountain Standard Time 0 xffff9d90
Mountain Daylight Time 0 xffffaba0
Central Standard Time 0xffffaba0
Central Daylight Time 0xffffb9b0
Eastern...

Tone Commander 7210/7220 Network Administration Guide
13-102865  Rev. KPage 9 of 32
  10.  Check the box next to 066 Boot Server Host
Name.
  11. Select 066 Boot Server Host Name, then enter
the TFTP boot server’s IP address in the String
value field.
  12. Click OK.
  13.  002 Time Offset, “003 Router”, 004 Time
Server, and “066 Boot Server Host Name”
should now appear in the Scope Options pane.
To preclude the issuance of a new IP
address each time the phone reboots, it
is recommended that ICMP ping...

Page 10 of 3213-102865  Rev. K
Windows NT Server
Run DHCP Manager from the Administrative Tools menu.
Add Server
You can use an existing DHCP server for
assigning IP addresses to the telephones,
or add a new server.
  1.  To add a server, select Server from
the File menu, then select Add.
  2.  Enter the address of the new DHCP server.
Add Scope
  1.  Select the DHCP server.
  2. Select Create from the Scope menu.