THOMSON Dpl660ht User Manual

Operating your Receiver
6 Channel external input
An external decoder (Dts, Dolby Digital, etc…) or a
device with built-in multi-channel decoder and 6
channel output connector (DVD player, TV…) can be
connected to the 6CH input. It is therefore possible
to play any future 6 Channels coding (SACD, DVD
Audio) thanks to this connection. The external
decoder device will send the separated audio infor-
mation to the receiver that will then amplify the sig-
nal and send to appropriate speakers. 
To activate 6...

EN
19
Advanced Sound Control
Sound Enhancement Systems
This receiver is equipped with several built-in sound
enhancement systems.
Dolby Pro Logic II
The Pro Logic II mode uses the built-in circuit to steer the
Left, Center, Right and Surround left and right channel
audio signals and uses all five speakers  to play both stereo
and Dolby Pro Logic program source, such as TV and VCR.
Dolby Pro Logic II includes Dolby Pro Logic II Movie, Dolby
Pro Logic II Music and Dolby Pro Logic.
Use this mode to suit the...

20
Advanced Sound Control
Stereo
The Stereo mode uses the two main channel outputs
from the front speakers. Use this mode if you have
connected the front speakers only.  
DSP (Digital Sound Processor)
These digital sound effects resemble sounds in a real 
environment such as 
(STADIUM / THEATER / CONCERT /
CLUB / CHURCH / ARENA)
. DSP automatically converts
analog audio signals to digital ones which enables
you to adjust the sound without degrading the sound
quality. Different modes will give you...

EN
21
Advanced Sound Control
Fine Setting of the Speakers 
This receiver supports a wide range of speakers and 
subwoofers. For optimal surround sound enjoyment,
you need to register the speaker selection settings of
your audio system. If you buy this receiver with
accompanied speaker package, then this step has
been done for you.
Also, to make the surround sound more effective and
suit the acoustic conditions in your listening room,
you need to delay the signal from some of the speak-
ers. Such channel...

22
Advance Sound Control
Use a subwoofer to enjoy optimum sound.
• Subwoofer Phase: Try both settings and select the
sound preferred.
• Speaker distance:For optimum surround experi-
ence measure the distance between the speaker and
your favorite listening position.
1.  Press SETUPonce.
2. While the VFD display is showing L/R SML, press
UP/DOWN ARROW button to select.
3. Press OKbutton once to move to the next 
speaker setting.
4. Repeat step 3 to set up the next speaker
5. When set up is done, wait for 5...

EN
23
Troubleshooting Tips
Receiver/Tuner Operation 
ST indicator is off.
•  Adjust the antenna.
•  Press DIGITAL INPUT/ST/MONObutton to insure you
are not outputting in mono.
The signal is Mono. Severe hum or noise.
• The signal is too weak. Connect an external antenna.
• Adjust Antenna
• Reposition Antenna away from any electronics.
Remote Control Operation 
The remote control does not operate the unit.
•  Another source mode is selected on the remote. Press
the correct Source Button.
• No batteries...

24
Care and Maintenance
Disconnect the audio system from the power source before
performing any maintenance.
Cleaning
Clean the exterior of the system using a soft dust cloth.
Important battery information
• Remove the batteries to avoid leakage if you do not use
your remote control for more than one month.  
• Discard leaky batteries immediately as leaking batteries
may cause skin burns or other personal injuries. 
• Dispose of batteries in the proper manner, according to
provincial and local...

EN
25
Universal Remote Control
stereo
DISC
tape
RDS
ptym
e
m
o2
3
6 5 4
789 1PLAY
FWD
STOP REV
PAU S E
hifi
0
vcr/sat
tvdigital
cd
sat/cabdvdtheater
modes
delaytunervideo
/ vcrstereo
level up
prprdownREC vcrdtsdvd /cdrep.
mixMUL
TI PRODUCT
rc 1000
Switch the key to tv position to control the TV.
According to the devices and when they
were put on the market, all the functions
represented on this page will not
inevitably be available.
According to the devices and when they
were put on the market, all the...

Universal Remote Control
26
pr
prTo change channels
2
3
6 5 4
789 1
0
Direct access to
the channels and
input of the 
digital  values
DISCPLAY
FWD
STOP REV
PAUSE
REC vcr
Disc Playing
DISC
tape
RDS
ptym
e
m
o2
3
6 5 4
789 1PLAY
FWD
STOP REV
PAU S E
hifi
0
vcr/sat
tvdigital
cd
sat/cabdvdtheater
modes
delaytunervideo
/ vcrstereo
level up
prprdownREC vcrdtsdvd /cdrep.
mixMUL
TI PRODUCT
rc 1000
Switch the key to dvd/CD position to control the Thomson DVD or CD unit
DVD
According to the devices and
when they...

EN
27
Universal Remote Control
Universal remote control Programming
You can program your remote control to control other devices.
Before making the following adjustments, see below for the 3 number code which corresponds to the brand of your device, and write it down in the chart
below.
1. Position the key on the device that you want to control.
2. Keep the RDS menukey down and enter the 3 number code.
3. Release the RDS menukey.
• Try to control the device by turning it off and then on with
• If this...