Home > Thomson > Home Theater System > THOMSON Dpl560ht User Manual

THOMSON Dpl560ht User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual THOMSON Dpl560ht User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 13 Thomson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Getting Started
    Preferred surround placement 
    Location
    If possible, place surround speakers to either side of
    the listening area, not behind it. 
    Height
    If space permits, install surrounds 2-3 feet above
    viewers. This helps to minimize localization effects.
    Aiming
    Aiming surrounds straight across the room, not down
    at viewers, helps create a more open, spacious sur-
    round sound field. 
    Advanced Setting
    Alternative Surround Placement 
    Rear wall
    If rear wall mounting is the only choice, aim the
    speakers at each other (A), towards the front (B) or
    even towards the sidewalls (C, D). Experiment with
    placement until surround sounds seem to envelop
    you, rather than coming from behind you. 
    No adjacent walls
    Surrounds can go on stands facing each other to
    approximate the preferred sidewall mounting (A), or
    to the sides or rear of the viewing area aimed
    upwards. In the latter case, they can go right on the
    floor, or preferably, a few feet off the floor such as
    on end tables (B). 
    8
    Courtesy Dolby Laboratories
    Courtesy Dolby Laboratories
    Courtesy Dolby LaboratoriesCourtesy Dolby Laboratories Courtesy Dolby Laboratories
    DPL560-EN  4/11/02  5:27 PM  Page 12
     
    						
    							Getting Started
    EN
    9
    Test Tone / Channel balance
    Channel balance
    Your receiver is equipped with a test signal generator
    for balancing the channels. As the signal travels
    from channel to channel, press LEVEL key to adjust
    corresponding channel and adjust by rotating the
    volume knob until all channels are at the same loud-
    ness level.
    Level adjustment & surround channel level expec-
    tation
    Even though you adjust the surround channel to be
    as loud as the others on the test signal, youll find
    that on actual program material the surround chan-
    nel is usually much lower than the front. Dont be
    tempted to readjust the surround level; program pro-
    ducers use surround mostly for subtle atmosphereics
    and ambience, and only rarely for special effects. A
    good surround mix doesnt call attention to itself; if
    it did, it would soon become distracting. 
    Connecting for Power 
    Make sure you connect all your other electronic com-
    ponents and the
    speakers before plug-
    ging your receiver
    into the outlet. Plug
    the power cord in
    the wall outlet,
    matching the wide
    blade of the plug with the wide slot in the outlet. Be
    sure to insert the plug completely.
    Using Headphones
    To listen privately through your
    audio system, use the PHONES jack
    on the receiver. However, make
    sure you turn down the volume
    before you put on the head-
    phones. Increase the volume to the
    desired level after headphones are in place.
    Once headphones are connected, “HEADPHONE
    DOWNMIX” will scroll on display. This feature auto-
    matically converts multi-channel speaker outputs to 2
    channel stereo for your listening pleasure.
    Hearing Comfort & Well-Being
    •  Do not play your headset at a high volume.
    Hearing experts advise against continuous extended
    play.
    •  If you experience a ringing in your ears, reduce
    volume or discontinue use.
    Factory Setting
    The DPL560 is preset to the following settings when
    you first power the receiver up right out of the box:
    Function = Tuner
    Volume setting = 45
    Bass & treble = 0 dB
    Speaker settings: Center, rear, front = small
    Subwoofer = on
    NOTE
    The system is equipped with Dolby Digital,
    and manufactured under License from Dolby
    Laboratories.
    Dolby Digital
    Manufactured under
    license from Dolby
    Laboratories. “Dolby”,
    “Pro Logic” and the
    double-D symbol are trademarks of Dolby
    Laboratories. Copyright 1992-1997 Dolby
    Laboratories, Inc. All Rights Reserved.  
    NOTE
    All preset radio stations and surround sound setting
    will be lost after factory setting is restored.  You may
    restore factory setting with the following procedures:
    1. Enter Standby mode
    2. Press SURR. MODEkey when holding SOURCE UP.
    3. All preset stations will reset to FM87.5MHz and all
    receiver settings restore to default settings as
    described above.
    Courtesy Dolby Laboratories
    Manufactured under License from
    Digital Theater Systems, Inc. US Pat. No.
    5,451,942 and other world wide patents
    issued and pending. “DTS Digital
    Surround”, are trademarks of Digital Theater Systems,
    Inc.  copyright 1996 Digital Theater Systems, Inc. All
    Rights Teserved.
    DPL560-EN  4/11/02  5:27 PM  Page 13
     
    						
    							Operating Your Receiver
    Receiver Controls 
    1. ON/ECO
    To turn the unit on/ off. When the system is turned on, the unit
    will go to the mode it was in before powered off.
    2. MUTE
    To mute speakers and headphone out.
    3. PHONES
    Plug your headphones (not supplied) into it  for your private
    enjoyment. Speakers will be off when phones are inserted. 
    4. Source Buttons 
    To select sound source. For example, CD, SAT etc. 
    5.  Display 
    To display current status of the receiver.
    6.  Sound Control 
    Let you adjust the sound – volume, treble, bass & level. 
    •  To change the VOLUME, turn the large knob. 
    •  To adjust TREBLE or BASS, press relevant button and turn the
    knob. (Stereo only)
    •  To change the volume of individual speaker, press LEVEL but-
    ton repeatedly to select the speaker, then turn the knob to
    adjust the level. 
    7.  DSP (Digital Sound Processor)
    Press this button to select the DSP mode 
    (STADIUM/CONCERT/THEATRE/ARENA/CHURCH/CLUB/OFF) you
    want. 
    8.  SETUP FUNCTION
    • To adjust the speaker size, speaker distance, speaker phase,
    night mode, sleep and display dimmer.
    • In SLEEP mode, you can set the receiver to turn off after 5 to
    120 minutes. 
    9. TUNING UP / DOWN
    Press for about 2 seconds to search for previous / next station in
    descending / ascending frequency direction.
    In preset mode, press to select previous / net preset station.
    In tuning mode, press once to manual fine tune.10.  SURR. MODE 
    Press repeatedly to select the surround mode you want. ( refer
    to “Advanced Sound Control” on page 20)
    11. MEMORY
    Press to toggle between manual tuning mode and preset sta-
    tion mode, Press and hold to manually store tuner station in
    preset mode.
    12. BAND
    Press to choose between FM/MW/LW in TUNER mode, press and
    hold to automatically search and save preset stations (FM only).
    13.  TEST tone
    When pressing it briefly, a short noise (test tone) will be gener-
    ated in the speakers one by one so that you can adjust the vol-
    ume of individual speaker.
    14. EQ 
    Press repeatedly to select the desirable EQ mode (music style) –
    OFF, CLASSIC, JAZZ, POP, ROCK, VOCAL, FLAT. Your choice will
    be saved automatically.(Only available in Stereo mode)
    15. DIGITAL INPUT/  ST / MONO
    Press repeatedly to select the input device (analog/ optical/ coax-
    ial). In FM mode, press to toggle between stereo and mono.
    16. V-AUX Input
    For convenient use of your digital camera, family game
    machines, second VCR, etc.
    MUTE
    BASS/TREBLEVOLUME
    LEVEL
    HOME THEATER AUDIO VIDEO RECEIVER DPL560HT
    PHONESTUNING MEMORY BANDSETUP TEST TONE EQ DIGITAL INPUT
    ST / MONO
    OKSURR  MODE 
    DSP MODE  SOURCE
    DIGITAL
    VIDEO V-AUX
    L - AUDIO - R
    SOURCE
    ON/ECO
    1
    2347
    6
    89
    10
    1112
    1314
    1516
    5
    10
    DPL560-EN  4/11/02  5:27 PM  Page 14
     
    						
    							Operating Your Receiver
    EN
    11
    Your Remote Control 
    Please be sure you have inserted the batteries into the
    remote control (see relevant section on page 3.) You can
    test it by pressing any button.
    1. ON/OFF 
    To turn on or off the receiver and Thomson DVD. 
    2. Source Buttons
    To turn on and select various audio/ video sources. 
    3. PR+, PR- (Channel Buttons) 
    To select programmed stations (in TUNER mode).
    4. VOL (Volume Buttons)
    To adjust the volume.
    5. MUTE
    To mute all audio outputs.
    6. Number Buttons
    To access directly a pre-set station (in TUNER mode) or to
    peripheral devices .
    7.  MENU (Tuner Mode only)
    • Press TUNER
    • To store Preset Stations. (For details, refer to Storing and
    Recalling Stations in Memory on page 17.)
    8. Operation Buttons 
    • PLAY, RECORD, STOP and PAUSE keys are only for easy
    control of Thomson DVD player, DVD. The remote control
    currently operates most Thomson, RCA and GE products.
    9. DIGITAL
    Select the way your audio/video components are connected
    to the receiver (Analog, Optical or Coaxial).
    10. TUNER UP/DOWN
    In TUNER mode, press TUNER on the remote. 
    • Press TUNER UP and TUNER DOWN keys to tune down or
    up the radio frequency. 
    11.  SURR (Surround Sound Control)
    Press to change the surround sound settings. The display
    will toggle among  DOLBY DIGITAL, DTS, PRO LOGIC /
    STEREO.
    12.  HIFI/DVD
    Press the appropriate key to control either the receiver or a
    compatibleDVD player (Thomson brand only)
    Note: After pressing DVD, you must press HIFIto enable
    all receiver functions on the remote.
    1
    4
    2
    35
    9
    11
    10
    6
    7
    8
    12
    DPL560-EN  4/11/02  5:27 PM  Page 15
     
    						
    							Operating Your Receiver
    •  Audio output is in DTS mode.
    •  Audio output is in Dolby Digital mode.
    •  Audio output is in Dolby ProLogic mode.
    •  Tuner stereo signal detected.
    •  Tuner station detected.
    •  Speaker Icons.•  Unit in Sleep mode.
    •  Unit in Memory mode.
    • Tuner frequency unit.
    • Radio data system is available.
    SLEEP
    MEMORY
    KHz 
    MHz
    12
    Display
    LS RSLFE
    R CL
    RDS
    ST
    TUNED DTS
    DPL560-EN  4/11/02  5:27 PM  Page 16
     
    						
    							Operating Your Receiver
    EN
    13
    Switching on/off
    •   To switch on the receiver, press ON/ECO button
    once, or any source button on the remote control. 
    •  Standby: when the receiver is on, press the 
    ON/ECObutton once to activate the standby mode.
    •  To switch off the unit completely, unplug the
    power cord from the socket
    Selection of Audio/Video source
    When one of the source buttons is pressed, the audio
    and video input corresponding to the name will be
    activated.
    The receiver acts as a switching device between all
    the sources that are plugged into it.
    Example 1: 
    If you connect a DVD player to the DVD input
    (audio + video) on the receiver and press the source
    button repeatedly until DVDis selected, you will be
    able to have the sound and image transmitted by
    the DVD. 
    Example 2: 
    Based on the example 1, the DVD is playing , if a
    VCR is connected  to the VCR 1 input (audio +
    video) of the receiver, press the VCR/VAUXbutton ,
    or press source button repeatedly until VCRis
    selected, image and sound from the VCR source will
    replace the DVD.
    NOTE
    Your receiver has a back up memory to keep
    your settings like preset radio station for
    about 2 weeks in case electricity outage
    occurs. If the receiver is unplugged for more
    than 2 weeks, all the settings will be lost and
    reset to factory settings.
    MUTEON/ECO
    PHONESSOURC
    DIGITALSOURC
    TUNING MEMORY FM/AM SOURCELSOURCE
    TUNING MEMORY FM/AM SOURCELSOURCE
    TUNING MEMORY FM/AM SOURCELSOURCE
    DPL560-EN  4/11/02  5:28 PM  Page 17
     
    						
    							Operating your Receiver
    You can connect up to 7 audio/video sources to this
    amplifier:
    Source button Corresponding connector 
    (receiver front panel)  (receiver back panel)
    - DVD  DVD IN (audio / video)
    - SAT  SAT IN (audio / video) 
    - VCR VCR IN (audio / video)
    - VAUX V-AUX IN (audio / video)  
    - CD CD IN (audio only)
    - TV TV IN (audio only) 
    - TAPE TAPE IN (audio only)
    - FM/AM built-in 
    When a source is selected, the source name will be
    shown on the display.
    NOTE
    1. Your receiver has a built in tuner. Just con-
    nect the appropriate antenna on the back of
    the receiver and you will be able to listen to
    radio stations. (See details in Tuner section)
    2. Other sources can be connected to the
    above standard source. Example: you can con-
    nect a LD into the DVD inputs.
    3.  Refer to the Connecting To Audio-Visual
    Components section for details on connec-
    tion. 
    14
    DPL560-EN  4/11/02  5:28 PM  Page 18
     
    						
    							Operating your Receiver
    EN
    15
    Using the receiver to play a source
    After having properly connected a source (DVD, CD,
    VCR) to the receiver, you can partly control them
    through the receiver.
    Playing a DVD with the receiver
    1.  Connect a DVD player to the receiver (see connect-
    ing your receiver for details) 
    2.  Press ON/ECOto switch on the receiver
    3.  Select the DVD source.
    4.  Switch ON the DVD player and start playback
    5.  Switch ON your TV
    6.  Select the appropriate A/V channel on the TV
    (refer to your TV manual for details) until the image
    from the DVD player is displayed
    7.  Set the sound Mode if needed (see Advanced
    sound control for details)
    Example 1: 
    To play 5.1 Dolby Digital surround sound 
    Press SURR. MODEbutton until Dolby Digital
    appears on the Display and all of the speakers’
    icons light up.
    Example 2: 
    DVD:You may also need to select the Dolby Digital
    5.1 on the DVD disc menu to have the digital sur-
    round enabled providing that the disc is encoded
    with Dolby Digital 5.1 (please refer to the DVD
    player and DVD disc instruction)
    Example 3:
    LD:You may need to select a different Audio
    Channel on your LD (refer to your LD player manu-
    al)
    8.  Adjust volume knob accordingly
    NOTE
    To play Dolby Digital sound / DTS, the source
    must be connected to the receiver via the opti-
    cal or coaxial terminal 
    DPL560-EN  4/11/02  5:28 PM  Page 19
     
    						
    							Operating your Receiver
    Operating the Radio
    The receiver has a built-in tuner that allows for
    AM/FM radio function.
    Manual tuning
    1.  Connect the FM and AM antenna accordingly (see
    Connecting the Antenna on page 5 section for
    details)
    2.  Press ON/ECO to switch on the receiver.
    3.  Press SOURCEkeys to enter TUNER mode.
    4- To select band, press the BAND button to toggle
    between AM/FM mode. 5- Tune the stations by pressing  TUNING UP or
    DOWNrepeatedly until the desired station is found.  
    Alternatively, you can press and hold TUNING UPor
    DOWNfor about one second to activate the 
    automatic SEARCH function. In this mode the receiver
    will automatically tune frequencies until it finds a
    station
    Select sound effect if needed by pressing Preset EQ or
    DSP sound (see Advance sound section for details)
    TUNING MEMORY BAND SOURCESOURCE
    NOTE
    1.  If there is interference, modify the location
    of the antenna until the optimal sound is heard.
    TV and other electronic devices could be the
    cause of interferences so try to position the
    antenna away from them.
    2.  Weak signal can affect the auto Search
    function. Adjust the antenna for better recep-
    tion for more efficient search.
    16
    MUTEON/ECO
    PHONESSOURC
    DIGITALSOURC
    TUNING MEMORY FM/AME
    E
    TUNING MEMORY FM/AM SOURCELSOURCE
    DPL560-EN  4/11/02  5:28 PM  Page 20
     
    						
    							EN
    17
    Operating your Receiver
    Storing radio stations:
    The receiver can store up to 40 radio stations in
    memory. You can enter every single radio station
    yourself or the receiver can store all available radio
    station  automatically in an ascending order. 
    Automatic preset storing : (FM only)
    1.  Select the band by pressing BAND
    2- Press and hold  BAND
    on the main unit for 3
    seconds. “MEMORY” will
    be displayed in red and
    will blink during the
    automatic storing
    process. 
    Radio frequencies will be scanned and radio station
    stored automatically. When all available radio sta-
    tions are stored or if all 40 memory locations are full,
    the auto preset will stop.
    Manual preset
    1. Select the band by pressing BANDrepeatedly 
    2. Tune to a radio station (see Manual tuning on
    page 16 above for details)
    3. Press and hold MENU
    on the remote control.
    MEMORY will appear
    on the display
    4. Select a preset station
    number.
    5. Press Menuagain to confirm selection.
    Retrieving preset stations
    1.  Press BANDto select tuner mode
    2.  Press MEMORY/MENUbutton to enter preset set-
    ting mode (MEMORYicon shows on display), Press 
    + PR - to select preset station.
    NOTE
    Weak signal can affect the Automatic Preset
    Storing function efficiency. Adjust the antenna
    for the best reception for more efficient search.
    TUNING MEMORY FM/AM SOURCESOURCE
    TUNING MEMORY SETUP TEST TONOK
    TUNING MEMORY BAND SOURCESOURCE
    TUNING MEMORY BAND SOURCESOURCE
    TUNING MEMORY BAND SOURCESOURCE
    DPL560-EN  4/11/02  5:28 PM  Page 21
     
    						
    All Thomson manuals Comments (0)

    Related Manuals for THOMSON Dpl560ht User Manual