ThermovisionFLIR FPTSeries Payload Installation Guide

F-Series and PT-Series 
Payload Installation 
Guide 
 
 
FLIR Commercial Systems, Inc. 
70 Castilian Drive 
Goleta, CA 93117 
Phone: 888.747.FLIR (888.747.3547) 
International: +1.805.964.9797 
www.flir.com
 
 
 
 
Document Number: 427-0031--00-12 
Version: 110 
Issue Date: March 2011 
This document is controlled to FLIR Technology Level 1.  The information contained in this document pertains 
to a defense article controlled for export by the International Traffic in Arms Regulations (ITAR).  FLIR trade...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
2 
 
 
© FLIR Commercial Systems, Inc., 2011. All rights reserved worldwide. No parts of this manual, 
in whole or in part, may be copied, photocopied, translated, or transmitted to any electronic 
medium or machine readable form without the prior written permission of FLIR Commercial 
Systems, Inc. 
 
Names and marks appearing on the products herein are either registered trademarks or 
trademarks of FLIR Commercial Systems, Inc. and/or its...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
3 
 
Payload Installation / Replacement 
This manual describes the installation of a replacement payload for the F-Series or PT-
Series cameras. If you need help during the installation process, please call to speak with 
our support experts (877-773-3547). 
This manual includes the following topics: 
 Installation Overview 
 Removal of the existing payload  
 Installation of the new payload 
 Camera configuration  
For safety, and to achieve...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
4 
 
Figure 1: Payload Label
Be safe when handling cameras that are mounted in elevated locations. Ensure the 
installation is done under working conditions that are free of known dangers and 
according to recognized industry safety standards. 
Installation Overview 
In order to install the new payload, it is necessary to remove the existing payload first. 
Once the new payload is physically installed in the camera, it may be necessary to change...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
5 
 4) An Ethernet connection to the PT-Series or F-Series Camera 
Removing the Old Payload 
If possible, remove the camera from its mount and place it on a work surface that 
provides ESD protection. If the payload is to be replaced while the camera is mounted, 
take proper safety precautions and ensure the work is performed according to 
recognized industry safety standards. 
1) Shut down the camera and turn off the camera power supply. 
2)...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
6 
 
3) Hook each end of the FLIR Payload Removal Tool under one of the captive screws 
and pull firmly to disengage the payload from the housing.  
 
Note: If a FLIR Payload Removal Tool is not available, it 
is possible to remove the payload with your hand. To 
make it easier to get a grip on the payload, there is an 
indentation or notch on each side as shown in the 
image.  
4) Slide the payload out of the housing and place it in a 
bag that...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
7 
 
Installing the New Payload 
Handle the replacement payload carefully so that the silicon lubricant on the O-ring stays 
intact. 
 
1) Insert the new payload into the housing by lining up the rails on the payload with the 
guides in the housing. With an F-Series camera, the guides will be on the sides of the 
housing. With a PT-Series camera, the guides are at the bottom of the housing. Take 
care that no wires are pinched and the O-ring in...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
8 
 Important: Ensure the payload is inserted fully before tightening the hex screws. 
 
The bottom of the payload should be flush with the bottom of the enclosure. 
3) Once the new payload is seated properly, tighten the four screws to secure it to the 
housing.  
4) Power up the camera and confirm that the new payload is operating and provides 
video. 
 
  

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
9 
 
Camera Configuration 
If the replacement payload is the same type as the original payload, it is not necessary to 
make any configuration changes. If the replacement payload has a different FOV or 
resolution, the configuration should be updated to match the new payload. 
After modifying any parameters, it is necessary to save the changes and then restart 
(stop and start) the Nexus server. Once all the changes have been made, it is a good...

427-0031--00-12  Rev. 110    Payload Installation Guide 
 
10 
 5) First make a backup of the existing configuration. Then if the new payload is 
replaced with the original payload, the matching configuration can be easily 
restored. Select the Configuration File link on the left side of the page. 
 
You can back up the configuration and keep a copy on the camera; that way it is easy 
to restore. Simply type in a unique name in the Backup to file field and click Backup. If 
necessary, the original...