ThermovisionFLIR FCSeries Quick Connect Guide
Have a look at the manual ThermovisionFLIR FCSeries Quick Connect Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 33 Flir manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
427-0073-12-28 Rev 100 May 2014 FC-Series Camera Quick Connect Guide For installations that are using the Concealed Cable Mounting Arm, refer to the installation manual for instructions: FLIR FC-Series Installation Manual (427-0073-12-12) Caution! Note Except as described in this guide, do not disassemble the FC-Series camera. Damage to the camera can occur as the result of careless handling or electrostatic discharge (ESD). Prior to making any connections, ensure the power is switched off. Power: Power Over Ethernet Plus (PoE+) or 14 - 32 Vdc or 18 - 27 Vac Power terminal blocks: wire size from 16 AWG to 20 AWG Analog Video Cable: BNC-terminated RG-59/U solid-center coax cable Accessory I/O Cable: wire size 26 AWG, stranded (1 mm diameter including insulation) Phoenix Contact 1780493 spring-cage and pierce contact technology Items Included in Kit 3 mm hex 2.4 mm slotted screwdriver key 427-0073-12-28 FC-Series S Quick Connect.fm Page 1 Friday, May 16, 2014 9:06 AM
427-0073-12-28 Rev 100 May 2014 Ste p 1Remove cover: Using 3 mm hex key, loosen four captive screws. Removal of sunshield not necessary. Ste p 2Install cables through sealing gland: Ste p 3If using conventional power cable, strip cable as described below: Access captive screws through slots in sunshield. Video coax Gland nut EthernetAccessory Power cableGround Re-tighten gland nut after installation is completed. Fill any unused hole with orange plug. (0.8±.20 in)20.0±5 mm Remove outer jacket (0.2±.04 in)6.0±1 mm Strip ends 3 Places Min diameter = 6.8 mm (0.27 in)Max diameter = 9.4 mm (0.37 in) Power Cable 427-0073-12-28 FC-Series S Quick Connect.fm Page 2 Friday, May 16, 2014 9:06 AM
427-0073-12-28 Rev 100 May 2014 Ste p 4Te r m i n a t e c a b l e s : Caution! Connection Purpose 1 3-pin Jumper Lens heater on/off 2RCA Analog video test point 3BNC Analog video 43-pin Terminal AC/DC Power 5 Ethernet PoE power, communications, IP video stream 6 6-pin terminal J8 General purpose I/O (GPIO) 7 Reserved for future use Do not connect Ta b l e 1 - 1 : P o w e r C o n n e c t o r 1Chassis 2Vac/dc - 3Vac/dc + Table 1-2: GPIO Connections - J8 Pin Connection Pin Connection 1 Chassis ground 4GPIO In (digital ground) 2 GPIO Out 5 GPIO In (+5V) 3 GPIO Out 6 Chassis ground Pins 4 and 5 should not be connected to any voltages or power sources outside the camera. Damage to the camera may result. Reserved J3 pin 1GPIO J8 427-0073-12-28 FC-Series S Quick Connect.fm Page 3 Friday, May 16, 2014 9:06 AM
427-0073-12-28 Rev 100 May 2014 Ste p 5Connect a ground wire between the ground stud on the back of the camera and the nearest earth-grounding point. Ste p 6Test camera: Power on the camera and test video. Use a web browser to test IP communications (default IP: 192.168.250.116; login: user/fliradmin) Ste p 7Tighten Cable seal gland nut to ensure a watertight seal. Ste p 8Replace cover: Alternately tighten the four captive screws in the cover; torque to 1.8 N-m (16.0 in-lbs). FLIR Systems, Inc. 70 Castilian Drive Goleta, CA 93117 USA PH: + 1 805.964.9797 PH: + 1 877.773.3547 (Sales) PH: + 1 888.747.3547 (Support) FX: + 1 805.685.2711 www.flir.com Corporate Headquarters FLIR Systems, Inc. 27700 SW Parkway Ave. Wilsonville, OR 97070 USA PH: +1 503.498.3547 FX: +1 503.498.3153 [email protected] Ensure the camera is properly grounded. Failure to properly ground the camera can lead to permanent damage to the camera. Typical to good grounding practices, the camera chassis ground should be connected to the lowest resistance path possible. FLIR requires a grounding strap anchored to the grounding lug and connected to the nearest earth-grounding point. Before installing the FC-Series camera you should read and understand the following documents which provide details regarding mechanical dimensions and installation safety. • FLIR FC-Series Installation Manual (427-0073-12-12) • FLIR FC-Series S Interface Control Document (427-00XX-XX-19S) Documents provided on the documentation CD or from the FLIR website 427-0073-12-28 FC-Series S Quick Connect.fm Page 4 Friday, May 16, 2014 9:06 AM