Telex Projector P170v User Manual

							QUICK SETUP
If you feel very comfortable with the installation of personal computer
hardware, you may want to use this section to help you quickly set up
your P170/P170v.
1. To ensure adequate cooling, place the P170/P170v on a hard, flat sur-
face, such as a table or desktop as shown below.
CAUTION!To prevent overheating, do not block the P170/P170v fan
intake and exhaust vents.
NOTE:Use Figure 4 to determine the projector position for the desired
screen image size.
AU DI O
AU DI O
AU DI OVIDEO
VIDEO
MONITOR
COMPUTER 1
COMPUTER 2
OUTPUT
SPARE LAMP
AC Voltage: 115V, 60 Hz
230V, 50 HzSEE BOTTOM
FOR FUSE
REPLACEMENT AND
VO LTAG E S W I T C H
VIDEO
VIDEO LRLRS-VHSTV2TV1
WARNING: HOTAllow unit to cool before
replacing lamp. Avoid touching
bulb or inside of reflector.
Replace with FXL Lamp.
!!
Figure 3.
P170/P170v
Position on a
Desktop
Figure 4.
Distance vs Image
+
Projector Distance
From Screen
4 ft (1.2 m)
6 ft (1.8 m)
8 ft (2.4 m)
10 ft (3.0 m)Image
Height
2.1 ft (0.6 m)
3.2 ft (1.0 m)
4.25 ft (1.3 m)
5.3 ft (1.6 m)Image
Width
2.8 ft (0.9 m)
4.2 ft (1.3 m)
5.6 ft (1.7 m)
7.0 ft (2.1 m)
6 User Manual 
						

							2. Connect the P170/P170v to the computer/s, audio source/s and an
AC wall outlet as shown in Figure 5. (The P170v can also be con-
nectedtooneormoreVCRsorLaserDiscplayers.
3. If you are going to use the remote control accessory, install the sup-
plied battery as shown in Figure 6.
4. Continue with the Operation section of this manual for instructions
on the use of your MagnaByte
®P170/P170v Color Computer Desk-
top LCD Projector.
OPENMINNEAPOLIS, MN U.S.A.
P/N: 47436-XXX
9VDC
Figure 6.
Remote Control
Battery
AUDIO AUDIO AUDIO
VIDEO VIDEO MONITOR
COMPUTER 1 COMPUTER 2 OUTPUT
VIDEO
VIDEO LR
LR
S-VHSTV2TV1
VCR or
Laserdisc
Audio
(P170v Only)
VCR, S-VHS
or Laserdisc
Audio
(P170v Only)
Line Level
Audio
Input
Computer
Monitor
VCR or
Laserdisc
Video
(P170v Only)
Computer
VideoComputer
Video
Super VHS
Video
(P170v Only)
External
Amplified
Speaker
Figure 5.
P170/P170v
Connections
User Manual 7 
						

							P170/P170v SETUP
This section is a detailed description of the setup for your MagnaByte®
P170/P170v. If you feel very comfortable with the set up of computer
hardware, you may want to use the Quick Setup section of this manual.
Positioning the P170/P170v On the Desktop
1. Place the MagnaByte®P170/P170v on a table or desktop as shown in
Figure 7.
NOTE:Ensure that the P170/P170v vents are not blocked. The
P170/P170v takes in cool air at the bottom of the projector. Hot air is
exhausted at the top of the P170/P170v.
2. To determine the distance between projector and screen, refer to Fig-
ure 8 and select the desired screen image size.
AUDIO
AUDIO
AUDIOVIDEO
VIDEO
MONITOR
COMPUTER 1
COMPUTER 2
OUTPUT
SPARE LAMP
AC Voltage:  115V, 60 Hz
230V, 50 HzSEE BOTTOM
FOR FUSE
REPLACEMENT AND
VOLTAGE SWITCH
VIDEO
VIDEO LRLRS-VHSTV2TV1
WARNING: HOTAllow unit to cool before
replacing lamp. Avoid touching
bulb or inside of reflector.
Replace with FXL Lamp.
Figure 7.
Positioning the
P170/P170v on
the Desktop
+
Projector Distance
From Screen
4 ft (1.2 m)
6 ft (1.8 m)
8 ft (2.4 m)
10 ft (3.0 m)Image
Height
2.1 ft (0.6 m)
3.2 ft (1.0 m)
4.25 ft (1.3 m)
5.3 ft (1.6 m)Image
Width
2.8 ft (0.9 m)
4.2 ft (1.3 m)
5.6 ft (1.7 m)
7.0 ft (2.1 m)
Figure 8.
Distance vs Image
8 User Manual 
						

							Connecting the P170/P170v
The P170/P170v must be connected to some video source, and to an AC
wall outlet. The P170/P170v can also be connected to a computer
monitor, audio source/s, additional video source/s and to an external
amplified stereo speaker system. (Only the P170v can be connected to a
composite or S-VHS video source.)
The following steps describe the connections needed.
1. Turn off all equipment.
2. Plug the MagnaByte
®P170/P170v into an AC wall outlet.
3. Audio input can be amplified by the P170/P170v and heard over the
built-in speakers. Connect a stereo or mono audio source, such as
the auxiliary output of an amplifier, a wireless microphone system,
CD player, or tape player to the
COMPUTER 1 AUDIOorCOM-
PUTER 2 AUDIO
jacks.
NOTE:The audio input must be connected with the appropriate video
input. For example, if an external audio source is desired with
COMPUTER 1 VIDEO, the audio source must be connected to
COMPUTER 1 AUDIO.
4. If desired, connect an external amplified, mono or stereo speaker
system to the
OUTPUT AUDIOjack on the P170/P170v.
NOTE:When a cable is plugged into the
OUTPUT AUDIOjack, the
built-in speakers are disabled.
5. Only the P170v can be connected to composite or S-VHS video
sources such as VCRs or LaserDisc players. If desired, use the com-
posite video cable to connect the video source to the
TV1 VIDEOor
TV2 VIDEOjack on the P170v as shown in Figure 9. (If your video
system has S-VHS capabilities, use the cable supplied with your
video system to connect to the
S-VHSjack on the P170v.)
NOTE:The
TV2audio input (LandR) is used for both theTV2 VIDEO
andS-VHSaudio sources on the P170v only.++
+
User Manual 9 
						

							6. If you are using an IBM VGA computer, the connections are
shown in Figure 9:
a. Unplug the monitor cable from the computer.
b. Plug one end of the supplied VGA cable into the video port of
the computer.
c. Plug the other end of the VGA cable into the
COMPUTER 1
VIDEO
orCOMPUTER 2 VIDEOjack on the MagnaByte®
P170/P170v.
f. To use your computer monitor along with your P170/P170v,
plug the monitor cable into the
OUTPUT MONITORjack on the
MagnaByte®P170/P170v.
AUDIO AUDIO AUDIO
VIDEO VIDEO MONITOR
COMPUTER 1 COMPUTER 2 OUTPUT
VIDEO
VIDEO L           R
L           R
S-VHSTV2TV1
VCR or
Laserdisc
Audio
(P170v Only)
VCR, S-VHS
or Laserdisc
Audio
(P170v Only)
Line Level
Audio
Input
External
Amplified
Speaker
VCR or
Laserdisc
Video
(P170v Only)
Super VHS
Video
(P170v Only)
TheBig Monitor3479875986235    88
IBM Compatible
PCs
Monitor
IB MCompatibleComputer
Figure 9.
P170v to IBM
Connections
10 User Manual 
						

							7. If you are using a Macintosh computer, the connections are shown
in Figure 10:
a. Unplug the monitor cable from the computer.
b. Plug the adapter labeled either “550093-0 or “550093-2 into the
monitor port of the computer.
c. Plug one end of the supplied VGA cable into the adapter on the
computer.
d.
Plug the other end of the VGA cable into the
COMPUTER 1
VIDEO
orCOMPUTER 2 VIDEOjack on the MagnaByte®
P170/P170v.
e. To use your computer monitor along with your MagnaByte
®
P170/P170v, select the adapter labeled either “550093-1” or
“550093-3.” Plug the adapter into the
OUTPUT MONITORjack
on the MagnaByte®P170/P170v; plug the computer monitor ca-
ble into the adapter.
NOTE:Simultaneous viewing is not possible with the 12-inch
Macintosh monitor.
+
AUDIO AUDIO AUDIO
VIDEO VIDEO MONITOR
COMPUTER 1 COMPUTER 2 OUTPUT
VIDEO
VIDEO LR
LR
S-VHSTV2TV1
VCR or
Laserdisc
Audio
(P170v Only)
VCR, S-VHS
or Laserdisc
Audio
(P170v Only)
Line Level
Audio
Input
External
Amplified
Speaker
VCR or
Laserdisc
Video
(P170v Only)
Super VHS
Video
(P170v Only)MACINTOSH
COMPUTER &
MONITOR
ADAPTER
550093-000 or -002
ADAPTER
550093-001 or -003
Figure 10.
P170v to MacIntosh
Connections
User Manual 11 
						

							Remote Control Battery
The optional remote control requires one 9V alkaline battery installed as
showninFigure11.
A new battery should be installed in the remote control unit under the
following circumstances:
·New remote control unit is received from the factory.
·LED on the remote control no longer lights when keys are pressed,
indicating a “dead” battery
·Operating distance between the remote control and the P170/P170v
becomes too short for your purposes, indicating a “weak” battery
Continue with the Operation section of this manual for instructions on
the use of your MagnaByte
®P170/P170v Color Computer Desktop LCD
Projector.
1. SLIDE THE BATTERY COVER
    BACK AND LIFT OUT.
OPEN
MINNEAPOLIS, MN U.S.A.
P/N: 47436-XXX
9VDC
2. PLUG IN THE BATTERY AND
    POSITION IT IN THE BATTERY
    COMPARTMENT.
MINNEAPOLIS, MN U.S.A.
P/N: 47436-XXX
9VDC
3. ALIGN THE TABS ON THE BATTERY
    COVER WITH THE SLOTS IN THE
    BACK CASE AND
    REPLACE THE COVER.
OPENMINNEAPOLIS, MN U.S.A.
P/N: 47436-XXX
9VDC
4. CHECK THE OPERATION BY PRESSING
    ANY KEY.  THE LED INDICATOR
    SHOULD BLINK RAPIDLY.
STANDBYFOCUS
BRIGHT CONTRASTVOLUME
SOURCE MODE MENU
Figure 11.
Remote Control
Battery Installation
12 User Manual 
						

							OPERATION
After you have connected the MagnaByte®P170/P170v as described in
either the Quick Setup or P170/P170v Setup sections of this manual, you
are ready to begin using your color desktop LCD projector.
Basic Operation
1. Slide open the lens cover door shown in Figure 13.
2. Turn on the P170/P170v desktop LCD projector. The POWER LED
(Figure 12) should now be steady orange, and the video source indi-
cators will be flashing to show that the MagnaByte
®P170/P170v is
being initialized. After intialization is complete, the video source in-
dicators will then begin scanning to show that the P170/P170v is
waiting for a video signal from one of the video inputs.
WARNING! To prevent burns when the P170/P170v is operating,
avoid touching the lamp access door and the surrounding area of the
rear panel.
3. Turn on the attached computer/s. One of the source indicators will
be steady green to show that the MagnaByte
®P170/P170v has ac-
quired a video signal from that video source.
CAUTION!The cooling fan protects the MagnaByte
®P170/P170v from
heat generated by the projection lamp. Always make sure that the air
intake and exhaust are not blocked.
!!
COMPUTER 1 COMPUTER 2 POWER
REPLACE
LAMP S-VHS TV 2 TV 1
Video Source
Indicators
Power
LED
Lamp
Replacement
LED
Figure 12.
MagnaByte®
P170/P170v
Indicators
WARNING
User Manual 13 
						

							4. Adjust the room lighting for optimum screen viewing. (The projec-
tor lamp is automatically turned on when the P170/P170v is turned
on.) You may press the
LAMPbutton to turn off the projector lamp
until your presentation begins.
5. Adjust the screen focus by rotating the lens (Figure 13).
6. To adjust the vertical position of the image on the viewing screen:
a. Lift the front of the projector.
b. Press the foot release bar shown in Figure 13.
c. Raise or lower the projector as desired, then release the bar.
NOTE:The keypanel and on-screen control settings will be the same as
they were when the P170/P170v was last used, if five seconds were
allowed to elapse before the P170/P170v was turned off.
7. To improve the imgage phase adjustment, display a colorful image
on the computer screen and select the on-screenFOCUScontrol. (It
is easier to adjust the MagnaByte
®P170/P170v with a colorful im-
age.)
8. Turn on your audio source (CD player, wireless microphone,
amplifier auxiliary audio output, etc.).
9.
Press
VOLUMEto adjust the volume of the P170/P170v built-in
speakers.
+
MagnaByte P170TELEX
Sliding Lens Cover Door
Focus Adjustment
Remote Control Sensor Foot Release Bar
Figure 13.
Height and Focus
Adjustments
14 User Manual 
						

							NOTE:If you have an external powered speaker system plugged into
the
OUTPUT AUDIOjack, turn it on and adjust the volume of that
external system. (The level at the
OUTPUT AUDIOjack is controlled by
VOLUME.)
10. Turn on and play the connected VCR, LaserDisc player, etc. (P170v
model only.)
11.
Press
SOURCEon the P170/P170v keypanel to select one of the com-
puter inputs, as indicated by the SOURCE LEDs shown in Figure 12.
(Only the P170v can also select from two composite video and one
S-VHS source.)
12. To further enhance or change the image on the MagnaByte
®
P170/P170v, refer to the Keypanel and Menu Mode On-Screen Con-
trol sections of this manual.
NOTE:Five seconds after you make a change, the image enhancements
that you have made will be saved. These saved enhancements will be
used as the default settings the next time that you activate your
P170/P170v.
13.
When you are not projecting an image, press
LAMPto turn off the
projection lamp.
14. After the MagnaByte
®P170/P170v has cooled, turn it off.
NOTE:To use your computer and monitor without disconnecting them
from the P170/P170v, the P170/P170v must be plugged into an AC wall
outlet and turned on. The
OUTPUT MONITORjack on the MagnaByte®
P170/P170v requires power to operate the computer monitor.
NOTE: The projector lamp doesnotneed to be on to use theOUTPUT
MONITORjack.
+
+
++
User Manual 15