Telex Projector Firefly P250 User Manual

P200/P250 SETUP
This section is a detailed description of the setup for your P200/P250.
Positioning the Firefly™P200/P250 On the Desktop
1. Place the P200/P250 on a table or desktop as shown in Figure 5.
NOTE:Ensure that the P200/P250 vents are not blocked. The
P200/P250 takes in cool air at the side of the projector.  Hot air is
exhausted at the rear of the P200/P250.
2. To determine the distance between projector and screen, refer to
Figure 5 and select the desired screen image size.
Connecting the...

2. Press and release the locking mechanism, then lift the P200/P250 to
its raised position as shown in Figure 6.
3. Plug the Firefly
™P200/P250 into an AC wall outlet (thePOWER
button will glow).
4. Audio input can be amplified by the P200/P250 and heard over the
built-in speakers. Connect a stereo or mono audio source, such as
the auxiliary output of an amplifier, a wireless microphone system,
CD player, tape player, VCR or LaserDisc to the
AUDIO INjack (use
one of the two audio cables shown in Figure...

7. If you are using an IBM VGA/SVGA computer, the connections
are shown in Figure 7:
a. Unplug the monitor cable from the computer.
b. Plug one end of the supplied VGA/SVGA cable into the video
port of the computer.
c. Plug the other end of the VGA/SVGA cable into the
COMPUTER
jack on the Firefly™P200/P250.
d. To use your computer monitor along with your P200/P250, plug
the monitor cable into the
MONITORjack on the Firefly™
P200/P250.
External
Amplified
Speaker VCR or
Laserdisc
Video
Super VHS
Video
Line...

8. If you are using a Macintosh computer, the connections are
shown in Figure 8:
a. Unplug the monitor cable from the computer.
b. Plug the adapter labeled either “550093-0 or “550093-2 into
the monitor port of the computer.
c. Plug one end of the supplied VGA/SVGA cable into the adapter
on the computer.
d. Plug the other end of the VGA/SVGA cable into the
COMPUTER
jack on the Firefly™P200/P250.
e. To use your computer monitor along with your Firefly
™, select
the adapter labeled either “550093-1” or...

Remote Control Battery
The remote control requires one 9V alkaline battery installed as shown in
Figure 9.
A new battery should be installed in the remote control unit under the
following circumstances:
·New remote control unit is received from the factory.
·LED on the remote control no longer lights when keys are pressed,
indicating a “dead” battery
·Operating distance between the remote control and the P200/P250
becomes too short for your purposes, indicating a “weak” battery
Continue with the...

OPERATION
After you have connected the Firefly™P200/P250 as described in the
P200/P250 Setup section of this manual, you are ready to begin using
your P200/P250 LCD notebook projector.
Basic Operation
1. Lift and rotate the mirror as shown in Figure 6.
2. Press
POWERto turn on the P200/P250 LCD notebook projector.
The keypanel will light up and the projector lamp will turn on; initially
the screen will be blue. After initialization, the Telex logo will appear.
WARNING! To prevent burns when the P200/P250...

9. PressVOLUMEto adjust the volume of the P200/P250 built-in
speakers.
NOTE:If you have an external powered speaker system plugged into
the
AUDIO OUTjack, turn it on and adjust the volume of that external
system. (The level at the
AUDIO OUTjack is controlled byVOLUME.)
10. Turn on and play the connected VCR, LaserDisc player, etc.
11. Press
SOURCEon the P200/P250 keypanel to select one of the
video inputs.
12. To further enhance or change the image on the Firefly
™P200/P250,
refer to the Keypanel and...

14. After the Firefly™P200/P250 has cooled and the fans have stopped,
you may unplug the P200/P250 from the AC wall outlet.
NOTE:To use your computer and monitor without disconnecting them
from the P200/P250, the P200/P250 must be plugged into an AC wall
outlet.  The
MONITORjack on the Firefly™P200/P250 requires power to
operate the computer monitor.
NOTE:The projector doesnotneed to be turned on to use the
MONITORjack.+ +
User Manual  13 

CONTROLS
The P200/P250 keypanel and Menu Mode On-Screen controls allow you
to customize the projected image and enhance the appearance of your
presentation. The function of each keypanel and on-screen control is
described below and the keypanel is shown in Figure 11.
Keypanel Controls
NOTE:All controls have on-screen graphics to indicate their relative
value or selection setting.
BRIGHTNESSPress the upper (+) button of theBRIGHTNESScontrol to increase the
overall image brightness. Press the lower (-)...

NOTE:The Alignment controls are functional only when the P200/P250
is not in “menu” mode.
MENUThis key controls the display of the on-screen controls “menu.”  If an
on-screen controls “menu” item is displayed, pressing this key will make
the display disappear  (on-screen displays normally disappear after five
seconds).  To enter “menu” mode and access the on-screen controls,
press and release
MENU/RESET, then press either the up or down
arrow key to “step” through the “menu” until the desired Menu Mode...