TeacCD Rewritable Drive W512S Owners Manual

 
Introduction 
TEAC CD-RW Installation Guide 1 
Introduction 
The TEAC CD-RW drive can write to CD-R discs at a maximum of 12X speed, re-
write to CD-RW discs at 10X speed, and read CD-ROM discs at 32X speed. (It is also 
capable of operating at slower speeds, if preferred.) CD-R discs enable you to create 
audio or data discs for permanent archival storage. They cannot be overwritten. You 
can overwrite CD-Rewritable (CD-RW) discs, typically up to 1,000 times.
The TEAC CD-RW drive is a SCSI device...

 
Recommended System Requirements 
TEAC CD-RW Installation Guide 2 
Front Panel 
disc tray:  
 Use the disc tray to load CDs into the drive. You can open the tray by 
pressing the eject button or by using the emergency eject mechanism. You can 
close the tray by pressing the eject button.  
headphone jack:  
 You can connect headphones or external speakers to this jack 
to listen to an audio CD being played on your TEAC drive. Use a 3.5 mm stereo 
mini-plug. For external speakers, connect a stereo...

 
Rear Panel 
TEAC CD-RW Installation Guide 3 
Rear Panel 
analog audio output connector: 
 You can use an audio cable to connect this 
connector to the audio input connector on a sound card. Pin assignments are 
described below: 
jumper pin configuration jumper: 
 The CD-RW drive includes seven pairs of 
jumper pins on the rear panel that allow you to set the SCSI ID number, 
termination, and parity. 
interface connector: 
 Use a standard 50-pin SCSI interface cable to connect the 
CD-RW drive to a SCSI...

 
Setting the SCSI ID Number 
TEAC CD-RW Installation Guide 4 
Configuring the CD-RW Drive 
Before you can install and operate the TEAC CD-W512S CD-RW drive, you need to 
do the following: 
❑ 
Install a SCSI adapter card in the host computer. For optimum performance, a 
PCI bus master SCSI adapter card (such as an Adaptec 2940 or equivalent) is 
recommended. Please refer to the SCSI adapter card documentation for 
installation instructions. 
❑ 
Set the SCSI ID number on the rear panel of the CD-RW drive...

 
Terminating the CD-RW Drive 
TEAC CD-RW Installation Guide 5 
Terminating the CD-RW Drive 
If you position the CD-RW drive at the end of a SCSI chain, you must “terminate” 
the CD-RW drive; however, do not terminate the CD-RW drive if it is not physically 
connected at the end of the SCSI chain.
If jumper pin S4 is closed (that is, if the jumper is seated on both pins), the CD-RW 
drive is terminated. If S4 is open (i.e., the jumper is not seated on both pins), the CD-
RW drive is not terminated.  
The...

 
Installing the CD-RW Drive 
TEAC CD-RW Installation Guide 6 
5. Connect the CD-RW drive to the SCSI host adapter card using a 50-pin 
interface ribbon cable. 
Be certain to connect pin 1 on the CD-RW drive to pin 1 on the SCSI adapter 
card. (Pin 1 on the interface cable is usually designated by a color stripe along 
one edge of the cable. Also, the interface ribbon cable connector may feature a 
tab on one side. Insert the cable so that the tab aligns with the notch in the 
interface connector.)...

 
Installing the CD-RW Drive 
TEAC CD-RW Installation Guide 7 
7. Connect the power cable to the power connector on the rear panel of the 
CD-RW drive. 
Insert the power cable plug in the correct orientation into the power connector. 
The plug is shaped so that it can be easily inserted in only one orientation; do 
not force the plug into the connector.
The +5v terminal is on the left as you face the rear of the panel; the +12v 
terminal is on the right. The two center terminals are ground terminals. 
8....

 
Recommended Adapters 
TEAC CD-RW Installation Guide 8 
Recommended Adapters 
You must install a SCSI adapter card in the host computer to utilize the CD-RW 
drive. For optimum performance, TEAC recommends a PCI bus master SCSI adapter 
card (such as an Adaptec AHA2940 or equivalent). Please refer to the SCSI adapter 
card documentation for installation instructions. 
Recommended Software 
Before you can record data onto CD-R or CD-RW discs using your TEAC CD-RW 
drive, you must first install...

 
Specifications 
TEAC CD-RW Installation Guide 9 
Specifications 
Model
CD-W512S 
Interface SCSI-2 (8 bit data bus)
Transfer Rate Write: 12X (1.8MBps)
Rewrite: 10X (1.5MBps)
Read: 32X maximum (4.8MBps)
Digital Audio Extraction 
Rate14X ~ 20X max.
Access Time 85 msec (1/3 Stroke)
Buffer Size 4MB
Write Methods Track At Once; Disk At Once; Multi-Session; Incremental
Write Verification Running Optimum Power Control to dynamically adjust 
laser write power
Logical Recording
FormatIS09660, UDF & CDR-FS Packet...

 
Specifications 
TEAC CD-RW Installation Guide 10 
Technical Support 
TEAC America, Inc. (USA)
Technical Support
Telephone: (323) 727-4860 • Fax: (323) 869-8751
Monday - Friday 8:00 a.m. - 5:00 pm
http://www.teac.com/dsp/new-dsp.html
E-mail: [email protected] 
CD-W512Sshort.fm  Page 10  Thursday, December 14, 2000  10:30 AM