Taxan Plus Ps100s Projector User Manual

E-20
R L
AUDIO OUT
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Connect to the projector’s AUDIO jack using a commercially available audio cable. When the audio jack of the equipment that
is to be connected is of the RCA phono type, make connection via the supplied audio conversion adapter.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio...

E-21
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
SOURCEKEYSTONEAUTOKEYSTONE
P
O
W
E
R
S
T
A
N
D
B
YS
T
A
T
U
S
M
EN
U
Q
U
I
C
K
 M
E
N
UFirmly plug in
all the way.To wall outlet
Operating
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.The STANDBY indicator will light in green, and the unit will enter the standby mode.
POWER
STANDBY STATUS
Lit green
Note:...

E-22
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-25.
1Press the SELECT (
) buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set....

E-23
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the POWER/STANDBY button.
The message display appears.
One more press of the POWER/STANDBY button as described in
the message will switch off the projection screen and cause the
projector to enter the power-off operation.
Note:
* The operation can be cancelled by pressing a button other than the
POWER/STANDBY button.
The POWER indicator will...

E-24
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
2Adjust the projection image to the screen.
Check that the screen is set level and vertically.
Adjustment of the Projection Screen
Turn the zoom ring to adjust the screen size of the projection image.Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.SOURCE...

E-25
Adjustment of the Projection Screen
SOURCEKEYSTONEAUTO
KEYSTONE
POWER
STANDBY STATUS
MENU
QUICK MENU
(
2)
(
1)
Note:
When the projector has a rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip / Horizontal Flip” on Page E-47.
Adjuster button
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the...

E-26
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-34 and the various items on
Pages E-41 to E-54.
Input Selection
VIDEO
FREEZE
MUTEECO
VOL KSTN ZOOMCANCEL QUICKMENU
ENTER
COMPUTER
QUICK
COLOR ADJ
ASPECT
AUTO
POWER/
STANDBY
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while...

E-27
General Operation
Selection of Aspect Ratio
This function selects horizontal and vertical picture proportions of the input
signal.
Press the ASPECT button while viewing the projected image and select the
aspect ratio.
Personal Computer Signal
Each press of the ASPECT button advances the selection one step in the se-
quence of Auto → Direct → Real, and then repeats.
Auto ............ Automatically enlarges or reduces the image to project a full screen in a ratio
of 4:3
Direct .......... Maintains the...

E-28
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
FREEZE
MUTEECO
VOL KSTN ZOOMQUICK
COLOR ADJ
ASPECT
AUTO
Note:
When an item other than Custom is selected with Quick Color Adj., the gamma, color temperature, and white...

E-29
Keystone Manual Adjustment
Use this to adjust for trapezoidal (keystone) distortion of the pro-
jected image. The projector has both an automatic and a manual key-
stone adjustment function. The manual adjustment will be described
here.
Adjustment Method
(1) Press the (
) buttons of the projector, or the (
) KSTN but-
tons of the remote control and set the left and right sides so that
they are parallel.
The keystone adjustment display appears when one of the buttons is
pressed.
General Operation...