Taxan Plus Kg Ps100s Projector User Manual

							E-50
Setup
Presentation Timer
The presentation is given while checking the timer displayed on the
screen.
The gauge display allows the remaining time to be known at a glance.
Select the item name “Presentation Timer” and select the setting contents
with the SELECT () buttons.
Setting contents:Off, 10 min. , 20 min. , 30 min. , 40 min. , 50 min. , 60 min.
To start the timer...
Press the MENU button and open the menu.
The timer display will appear at the lower right and the timer will start.
•Press the ENTER button to restart the timer. The timer will start with the
same time setting.
•Press the CANCEL button to close the timer display. The timer setting will
return to “Off”.
Moving the Position of the Timer Display
The SELECT (
) buttons on the remote control permit movement within
the movable range of the timer display. The blue gauge indicates the remaining time. When the gauge disappears,the
time is up.
The gauge continues to be displayed when the timer is stopped.Gauge (Blue)
[Timer Display]
When the remaining time is
“0” (Gray)
Note:
* The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
Movable Range of the Timer Display
Volume
This function adjusts the volume of the built-in speaker.
Select the item name [Volume] and adjust the sound level with the SELECT
() buttons. 
						

							E-51
Option
• Select menu name “Option”.
See “Menu Operation Method” on Page E-34 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-39.
Language
This function sets the language that is displayed on screen in
the messages and menu displays.
Select item name “Language” and press the ENTER button to open
the Language sub menu.
Select the language with the SELECT (
) buttons.
On Screen
This function switches on/off the messages displayed with a black
frame such as the input signal information and the aspect ratio.
Select item name “On Screen” and select the setting contents with the
SELECT () buttons.
On ............... The message is displayed.
Off .............. The message is not displayed.
Note:
Even when set to off, messages that are not in a black frame will be dis-
played.
Example of a display when the
FREEZE button is pressed
Freeze
Background
This function sets the screen color when the input source is no-
signal.
Select item name “Background” and select the setting contents with
the SELECT () buttons.
Blue ............ Sets a blue screen when there is no signal
Black ........... Sets a black screen when there is no signal 
						

							E-52
Startup Screen
Option
This is the selection of whether or not to display the logo screen
at startup time.
Select item name “Startup Screen” and select the setting contents
with the SELECT () buttons.
Logo ........... Displays the logo.
Blank .......... Does not display the logo.
Note:
When “Logo” is selected at the startup screen, the “TAXAN” logo is dis-
played.
Security Lock
A password can be registered and the security lock set in order
to prevent unauthorized use of the projector.
For instructions on using the security function, see “Protecting the
Projector with the Security Lock” on E-31.
Select item name “Security Lock” and select the setting contents with
the SELECT () buttons.
Disable ....... The security lock is disabled.
The projector can be operated without inputting the password.
Enable ......... The security lock is enabled.
The security lock is activated when the power is turned on, and
the password must be input in order to operate the projector.
Network Password
For details, refer to the “Image Viewer /  Wireless Network” sec-
tion.
 Applicable Model: KG-PS125X 
						

							E-53
Info.
• Select menu name “Info.”.
See “Menu Operation Method” on Page E-34 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-39.
Status
This displays information about the equipment.
Select item name “Status” and press the ENTER button.
There is a change to the status display.
Press the CANCEL button to return to the menu.
Display Contents:
Projector model, firmware version, and the internet home page ad-
dress of KAGA COMPONENTS.
Factory Default
This function returns the adjustments and settings of all the in-
put sources to the standard factory default values.
Select item name “Factory Default” and press the ENTER button.
There is a change to the display [Press “ENTER” to Factory Default
Set].
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
Items that are not set to the factory default:
Vertical Flip / Horizontal Flip, Language and Lamp Timer and Security
Lock.
Lamp Timer Reset
This function resets the lamp timer. Be sure to perform the reset
operation when the lamp cartridge has been replaced.
Select item name “Lamp Timer Reset” and press the ENTER button.
There is a change to the display “Press “ENTER” to Lamp Timer Re-
set”.
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu. 
						

							E-54
Resolution / Frequency
Info.
This function displays the resolution and frequency of the detected in-
put signal.
Lamp Timer
This displays the lamp timer.
This projector has an Eco mode function. The lamp life will differ between
Normal mode and Eco mode.
Lamp Life
Use only in Normal mode: approx. 2000 hours
Use only in Eco mode: approx. 3000 hours
* Lamp life will differ when there has been switching between the modes.
• When Lamp Life Has Been Reached
“Replace the Lamp Cartridge” is displayed on the screen for 10 seconds in
a 1-minute interval.
Please replace the lamp with a new one.
See “Replacing the Lamp Cartridge” on Page E-58 for information about
lamp cartridge replacement.
• When Over 100 Hours Have Elapsed Since Reaching Lamp Life
(Including Eco Mode)
[Warning!! System Shutdown] is displayed for 10 seconds and the power is
switched off. Pressing the POWER/STANDBY button under this condition
will not switch on the power. Please replace the lamp cartridge. 
						

							E-55
When an Indicator is Lit or Flashing
SOURCEKEYSTO
AUTKEYSTONE
POWER
UICK MENUSTANDBY
S TAT U S
MENU
The indicators on the projector’s control panel light or flash to
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode. See “Power Cable Connections and Switching the Power
On/Off” on page E-21.
What you should do
It is time to replace the lamp.
Replace with a new lamp cartridge.
The lamp has reached the end of its service life. The power
will no longer turn on.
The projector can be used for 100 hours after the lamp has reached
the end of its service life.
Replace with a new lamp cartridge.
The lamp cover is open.
The lamp cover is not properly mounted. Mount it properly.
The temperature is abnormally high.
•The temperature protector has been activated. If the room tem-
perature is high, move the projector to a cool place. If the
projector’s internal temperature is high, check the cooling fan’s
ventilation slots and clean them if they are clogged.
•When the temperature protector is activated, the power turns
off and in some cases will not turn back on immediately. In this
case wait about 90 seconds, then try again.
The fan has stopped.
Unplug the power cable and contact a store that sells the KG-
PS100S/KG-PS120X/KG-PS125X for repairs.
The lamp will not light.
Wait at least 90 seconds, then turn the power back on. If the prob-
lem persists, unplug the power cable and contact a store that sells
the KG-PS100S/KG-PS120X/KG-PS125X for repairs.
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power
cable and contact your store of purchase.
Thermal Protector
If the temperature within the projector becomes abnormally high, the thermal protector will be activated and will switch off the
power of the projector.
Should this happen, please take the following actions.
1. Switch off the power and disconnect the power plug from the wall outlet.
2. Check the following matters and take the required measures.
When the projector is being used in a location that has a high ambient temperature, set it up again in a cool location. Check the
outflow and intake holes and clean them if they are obstructed.
3. Wait about 60 minutes until the temperature of the projector drops.
If after having performed the above matters, the problem still has not been solved, please contact your store of purchase.
STANDBY
indicator POWER
indicatorSTATUS
indicator
POWER
STANDBY STATUS
POWER
STANDBY STATUS
POWER
STANDBY STATUS
POWER
STANDBY STATUS
When the power is on (Lit green)
Lit red
Standby mode (Lit green)
Blinks red
(1 second on/1 second off)
Lit green
Blinks red
(0.5 seconds on/0.5 seconds off)
Lit green
Lit green
Blinks red
(0.5 seconds on/0.5 seconds off)
Lit green
POWER
STANDBY STATUS
Lit red
Blinks green for 60 seconds (then,
lit green)
Indicator status
POWER
STANDBY STATUSBlinks red quickly
(0.1 seconds on/0.1 seconds off)
Lit green 
						

							E-56
Troubleshooting
Check the following matters before requesting servicing.
•Is the power cord plugged into a power outlet?
•Is the lamp cover properly mounted?
•Is the projector’s temperature high? To protect the projector, the power can-
not be turned on when the projector’s temperature is abnormally high.
•Has the lamp reached the end of its service life?
•Depending on the timing with which the power cord is plugged in (the power
is turned on), it may happen that the POWER indicator (LED) does not light
and the power does not turn on. This is not a malfunction. If this happens,
unplug the power cord then plug it back in.
•Is a connected input selected?
•Is the cable properly connected to the input terminal?
•When a computer is connected, are signals being output from the computer?
•Does the signal being input have a frequency usable with this projector?
•Are the brightness and contrast adjusted to the minimum?
•Is the STATUS indicator lit a steady red or flashing red?
•When the component signal of the DVD player is connected with the COM-
PUTER IN connector and the image is not output, is [Input Settings] of the
COMPUTER IN connector properly selected?
•For a Computer input, has the picture been properly adjusted?
•Is the projector properly installed?
•For trapezoidal (keystone) distortion, perform keystone adjustment.
Please note that depending on the projected picture and the projection con-
ditions, it may not be possible to eliminate keystone distortion completely.
•Is the lens properly focused?
•Are the screen and projector installed at the proper distance?
•Does the projection distance exceed the focusing range?
•Is there condensation on the lens, etc.?
If the projector is moved from a cool storage area to a warm place and the
power is turned on, condensation may form on the lens or internal optical
par ts. If this happens, wait until the condensation has evaporated before
using the projector.
•For a computer input, are the horizontal and vertical positions properly ad-
justed?
•Does the input signal have a compatible resolution and frequency? Check
the computer’s resolution.
•If the image is crushed in the horizontal or vertical direction or if it is not
displayed over the entire screen, select a different aspect ratio.
•When a component signal is being input, is the color space setting proper?
•For a composite input, is the tint properly adjusted?
•From the menu, select “Image” and adjust the “Picture Adj.” and “Fine Picture”.
•Other than [Settings], [Option] and [Information], selection will not be pos-
sible unless a signal is being input to the projector and the image/picture is
projected.
•Are the remote control unit’s batteries worn? Replace with new batteries.
•Is there an obstacle between the remote control unit and the projector’s
remote control signal sensor?
•Is the remote control unit outside of range?
•Are you pointing the remote control unit’s transmitter towards the projector’s
remote control signal sensor?
•Is the projector located near fluorescent lighting?
•See “When an indicator is lit or flashing”. Power does not turn on
No image is produced
Image is distorted
Image is out of focus
Image is not in proper posi-
tion and is not displayed
properly
Video image is crushed
Colors of the overall image
are strange
Characters flicker or colors
are offset for RGB inputs
Cannot select the menu
name
Remote control unit does
not operate
STATUS indicator is lit red
or flashing red Problem
CheckReference
PageE-21
E-60
E-55
E-55
—
E-26
E-16–19
E-54
E-64
E-41
E-55
E-50
E-41, 42
E-25
E-29, 47
E-24
E-15
E-15
—
E-42
E-64
E-27
E-44
E-41
E-41, 42
—
E-13
E-13
E-13
E-13
E-13
E-55 
						

							E-57
Cleaning
•Be certain to disconnect the power plug from the power outlet before cleaning.
•Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Do not leave rubber
or vinyl products in contact with the projector for long periods. Doing so could cause them to undergo qualitative changes or the
coatings may peel, etc.
Cleaning a Soiled Projector Main Unit
•Wipe with a lint-free, soft, dry cloth.
When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a
chemically-treated cloth is going to be used, please follow any written warnings.
•Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings
may peel, etc.
•When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust.
Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.
•Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.
Dirty Lens
•Clean using the same method you would use to clean a camera lens: Use a commercial blower for camera use or cleaning
paper for eye glasses. Be careful not to scratch the lens at this time.
Dust of the Intake and Outflow Holes
Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which
could cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours of usage.
•Switch off the power, check that the STANDBY indicator has
changed to a steadily lit green, then unplug the power cable.
•Clean out the holes from the outside using a vacuum cleaner.
Use the brush adapter of the vacuum cleaner to do this. Avoid
using the vacuum directly without attaching the adapter as well
as the use of a nozzle adapter.
Cleaning the Inside of the Projector
Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected
inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Please be sure to contact
your dealer.
SOURCEKEYSTONEAUTOKEYSTONE
POWER
STANDBY
STATUS
MENU
QUICK MENU 
						

							E-58
Replacing the Lamp Cartridge
• The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is
about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and
other factors.
Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp
means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from
test conditions at this company.)
• When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp
Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Follow the procedure
described on Pages E-59 and E-60 and replace the lamp cartridge.
• If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode
and no longer turns on.
• Contact a store that sells the KG-PS100S/KG-PS120X/KG-PS125X for a replacement lamp. Indicate you need a KG-
LPS1230 replacement lamp for the KG-PS100S/KG-PS120X/KG-PS125X (order code 000-155).
CAUTION
• Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop,
disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before
replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will
cause burns because of the high temperature.
• Do not remove any screws other than those specified.
• Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.
• If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can
be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your dealer or the store the projector was purchased. 
						

							E-59
Replacing the Lamp Cartridge
Preparations: Turning the projector upside-down on top of a soft cloth, etc., so that it does not get scratched makes it easier to
replace the lamp cartridge. Turn the projector right-side up after replacing the lamp cartridge.
1Unplug the power cord.
2Turn the projector upside-down.
3Remove the lamp cover.
(1) Loosen the lamp cover locking screw by turning it counter-
clockwise until it turns freely. (The screw will not come out.)
4Remove the lamp cartridge.
(1) Loosen the 2 screws of the lamp cartridge by turning them
counterclockwise until they turn freely. (The screws will not
come out.)(2) Grasp the handles of the lamp cartridge and pull upward to
remove the car tridge.
(2) Pull in the direction of the arrow and remove.