Tascam Dvd Player DV-D6500 Owners Manual

 Getting started 
8 
Getting started
 
English
 
To  make the Progressive scan mode selection active from the remote control\
 unit 
The unit supports the Progressive scan system as well as the conventional Interlace scan system. If your television or monitor  
supports the progressive video input, you can enjoy a high quality pictu\
re by making the Progressive scan mode active.
 
≠  
When the unit is turned on, and the scan mode selector on the rear panel\
 is set to REMOTE 
Press and hold down the...

 
Getting started 
9 
Getting started
 
You can enhance the sound quality by connecting either of the units DIGI\
TAL OUT jacks to the digital input of an  
amplifier, etc. by using an optical or a coaxal digital cable (optional). The d\
igital audio signal from a disc is directly 
transferred. If you connect the unit to a Dolby Digital or DTS decoder o\
r an amplifier with a built-in decoder by using an 
optional digital cable, you can enjoy high-quality surround sound.
For digital connection, connect the...

 Getting started 
10 
Getting started
 
English
 
Using the remote control unit 
Using the remote control, you can operate not only all the functions of \
the unit but also basic functions of your TV and  
amplifier/receiver. 
The battery compartment is located on the back of the  
remote control unit.  
1 
Press down on the point shown by  
the arrow at the top of the  
compartment cover, and pull up 
the cover to open the 
compartment. 
2 
Place the two supplied R6P (SUM-3)/ 
AA(15F) batteries in the...

 
Getting started 
11 
Getting started
 
You can operate your TV from the remote control unit. 
Setting the remote control signal for  
operating your TV 
1 
Set the TV - DVD switch to TV. 
2 
Hold down TV/VIDEO - CANCEL until step 4 is  
finished. 
3 
Enter the manufacturer code of your TV listed below 
by using the numeric buttons (0 through 9).  
Example:  
To  enter the manufacturer code 01: Press 0 then 
1. 
• When the unit is shipped, the manufacturer code is set to  (01). 
4 
Press ENTER....

 12 
Basic operations
 
English
 Basic operations 
In the following description, we assume that the buttons on the remote c\
ontrol unit are mainly used, however, you may  
use the corresponding buttons on the front panel if available. Before operation 
Press DVD STANDBY/ON   on the remote control unit or press STANDBY/ON   on the front panel. 
The STANDBY indicator on the front panel, which illuminates in red during stan\
dby, goes off. 
•You can turn on the unit by pressing the  
Á 
 button. In this...

 
Basic operations 
13 
Basic operations
 
We  recommend you to set the display language, TV monitor type and digital o\
utput before using the unit, depending on 
circumstances, by following the procedure below. 
See Changing the initial settings on and after page 47 for details abo\
ut each setting item. 
1 
Press CHOICE for a few seconds to bring up  
the first page of the DVD PLAYER SET UP 
display. 
The pull-down menu of the ON SCREEN  
LANGUAGE is already open. ON SCREEN LANGUAGE selection 
2 
Use...

 Basic operations 
14 
Basic operations
 
English
 
Basic playback 
This section describes basic operations for playback of DVD VIDEO, Audio\
 CD, Video CD and SVCD discs. For MP3 and  
JPEG disc playback, see the separate chapter on and after pages 39 and 4\
2. 
1 
Press OPEN/CLOSE to open the disc tray. 
2 
Place a disc in the tray. 
3 
Press OPEN/CLOSE to close the disc tray. 
The unit reads the disc information and the 
opening display appears on the TV screen. 
If a menu is shown on the TV screen...

 
Basic operations 
15 
Basic operations
 
Press   
Á  
. 
The unit starts playback from the beginning. 
About screen saver function  
•A  television monitor screen may be burned out if a static 
picture is displayed for a long time. To prevent this, the unit  
automatically activates the screen saver function if a static 
picture, such as an on-screen display or menu, is displayed 
for over 5 minutes.
• Pressing any buttons on the unit or the remote control unit 
will release the screen saver function...

 Basic operations 
16 
Basic operations
 
English
 
Resuming playback 
The unit can memorizes the position on a disc where you interrupt playba\
ck, and resume playback from that position  
later.
There are two resume modes (DISC RESUME and ON) you can set on the pre\
ference display. See page 52 for details 
about how to set the resume mode.
 
• When purchasing the unit, the resume mode is initially set to ON. 
•Y ou can deactivate the resume mode by setting RESUME on the OTHERS pr\
eference display to...

 
Basic operations 
17 
Basic operations
 
When the resume mode is set to DISC RESUME  
≠ 
While stopped, or no disc is inserted 
1 
Press OPEN/CLOSE to insert a disc whose interrupted position is memorize\
d. 
After loading the disc, the display window on the front panel shows ---\
-RESUME. 
If a disc for which you want to resume playback is already set in the di\
sc tray, you need not to follow the step 1. 
2 
Press   
Á  
. 
The display window shows RESUME PLAY and the unit resumes playback from the...