Sweex Router RO002 User Manual

English version
1

6.  If your IP address continues to be displayed as 0.0.0.0, click on “Renew”.
If after 1 minute your IP address still continues to show as 0.0.0.0, check the above steps. 
Still no Internet? Complete the following steps:
1.   Switch off the router and the modem.
2.   Disconnect the network cable between the router and the modem at the “WAN” port. 
3.   Switch on the router and wait until it is fully started up.
4.   Switch on the modem and wait until it is fully started up and...

English version
1

c.  Select ‘Dynamic IP” and click on “Next”. This setting is for providers who use a DHCP connection.
 
d.   Under “Hostname” enter the hostname you received from your provider.
e.   Leave “Domain name” empty.
f.   In order to enter the MAC address of your computer into the router, click “Clone MAC”.
g.  Click on “Next”. Click “Save” to save the settings.
h.   In order to check whether the Internet connection has been set up successfully, go to the status screen by clicking...

English version
1

Setting 3 PPPoE
1.  Log in to the Router (see the section “Accessing the Router” above).
2.   Left in the column, click on “Internet Provider Setup” or click on “Next”.
3.   Select the option "PPPoE”. This setting is for providers who use a PPPoE connection.
4.  Under “User Name” enter the user name you received from your provider.
5.   Under “Password”, enter the corresponding password.
6.   Click on “Next”. Click “Save” to save the settings.
7.   In order to check whether...

English version
1

Still no Internet? Complete the following steps:
1.  Switch off the router and the modem.
2.   Disconnect the network cable between the router and the modem at the “WAN” port. 
3.   Switch on the router and wait until it is fully started up.
4.   Switch on the modem and wait until it is fully started up and all the correct lights are lit.
5.   Reconnect the network cable between the modem and the router via the “WAN” port of the router. The “WAN” light should light up now.
6....

English version
1

5.  Reconnect the network cable between the modem and the router via the “WAN” port of the router. The “WAN” light should light up now.
6.   Connect the router via 192.168.22.1 and check your Internet connection in the status screen.
Setting 5 Static IP
1.   Log in to the Router (see the section “Accessing the Router” above).
2.   Left in the column, click on “Internet Provider Setup” or click on “Next”.
3.   Select the option "Static IP”. This setting is for providers who...

English version
1

Opening ports in the router (Virtual Server and DMZ)
The built-in firewall in this router cannot be disabled. However, ports can be opened for programmes and games which require this. 
We recommend using a fixed IP address for computers for which ports are opened. This is to ensure that these computers always use the same IP address as registered in the router. The router may assign a different IP address to the computer so that the forwarding or DMZ command no longer applies to...

English version
20

DMZ
In some instances, or when a game console is used, you may opt to place a computer or game console entirely outside the firewall. This can be done in the so-called “demilitarized zone” (“DMZ”). This option can be found in the main screen of the port settings (“Port Forwarding”) under (“Advanced”.) Note however, you no longer take advantage of the protection offered by the firewall of the router. All ports to the computer placed in the DMZ are open. Only a single computer can be...

English version
21

LAN settings
The network settings of the router can be changed as follows. Left in the column, click “Advanced Config".
Under “IP Address”, the IP address of the router (192.168.22.1) is stated. Click “Save” to save the settings. Your browser will not look for a new page. So do not wait, but log on to your router again, using the new IP address.
Changing the password
The standard login of the Sweex Broadband Router can be changed by clicking “System Tools” and then “Change...

English version
22
Here the firmware of the router can be upgraded. New firmware can be downloaded from the Sweex website under ”Service and support”. If the firmware file is zipped, make sure you select and extract the file first on a location on your computer where you can retrieve it easily. 
Now click “Browse” (Browse) and select the extracted firmware file. In most cases the name of this file will start with “Sweex_Firmware_RO002…”.In order to start the firmware upgrade, click “Upgrade”. Do not...