Surefire 311, 611 Tactical Light User Manual

							Model 311
 611
AMT Tactical Light
Users Manual
AMT Hardballer Pistols
1911A1  45ACP
Protected by US. Patents 4,777,754, & 4,856,218
Revision B    11_1_95 
						

							Model 311 & 611 Tactical Light
Introduction
   The Model 311 & 611 Tactical Lights provide a rugged and reliable source of high intensity
light mounted below the barrel of the weapon. The light can be activated by pressing on the
Pressure Switch attached to the handgrip or by pushing forward on the Switch Actuator Plates on
the sides of the Housing.
Installation
 1. Remove the magazine from the weapon and inspect the weapon to be certain it is not loaded.
 2. Disassemble weapon far enough to remove slide stop.
 3. Position H11 Housing so that hole in side is aligned with slide stop hole on the frame.
 4. Install new Slide Stop.
 5. Reassemble weapon as necessary.
 6. Using the Hex Wrench provided in the Kit, tighten the Set Screw in the base of the Housing
      until it contacts the trigger guard then turn the set  screw out 1/8 turn so as not to put tension
     on the Slide Stop. After firing 500 rounds the Set Screw may loosen, remove it and install the
     extra Set  Screw provided in the Kit.*
 7. Select the location desired on the weapon for mounting the Pressure Switch.
 8. Using the Velcro provided in the Kit, remove the paper backing from the “loop” section of
     Velcro and press in place on clean area. Wipe   with  alcohol first!
 9. Wipe the rear (flat) side of the Pressure Switch with alcohol to remove oil & dirt.
10. Remove the paper backing from the Velcro “hook” and press it in place on the rear side of
       the Pressure Switch.
11. Using Velcro, position the Pressure Switch on the weapon. Route the cable so that it does
       not interfere with the weapon operation.
12. Install the battery with the + terminal facing out.
13. Install the Lamp Module Assembly. Unit is now ready for use.
Kit Contents
! H11 Housing & Slide Stop
! L30 or L60 Lamp Module
! DL123A or DL223AC Battery
! Velcro Hook & Loop
! Extra Set Screw
! Hex Wrench
! Alcohol Wipe
! Users Manual
* Additional set screws are available in a Ten Pack, order P/N 12010-11.
Lamp Replacement
1. Unscrew Bezel from Lamp Module. Lift Lamp assembly out of Bezel.
2. Install replacement Lamp Assembly in Bezel and reassemble by screwing onto Lamp Housing
     until it is fully seated.
Battery Replacement
1. Unscrew Lamp Module from Housing and shake out old battery.
2. Install new battery with the + terminal facing out.
3. Reinstall Lamp Module. 
						

							Sure-Fire LLC
WARNING
Lithium batteries can explode or cause burns if disassembled,
shorted, recharged or exposed to fire or high temperatures.
Please handle with care. 
						

							Model 311 & 611 Tactical Light
Repairs & Replacements
     To obtain repair or replacement call Customer Service at 800-828-8809 (toll free) or 714-545-
9444 and obtain a Return Authorization number (RA). Then pack the unit carefully and return (no
COD’s please) to:
     SureFire LLC
     Repairs Department, RA# ___
     18300 Mt. Baldy Circle
     Fountain Valley, CA 92708
Surefire will pay any reasonable shipping costs to return the unit to you.
Warranty
     SureFire LLC warrants that its products will be free from defects in materials and
workmanship. SureFire LLC will repair or replace (at its option), without charge, any
product or part which is found to be defective under normal use and service. Such
repair or replacement shall be the purchaser’s sole and exclusive remedy under this
warranty. This warranty does not include normal maintenance and services and does
not apply to any products or parts which have been subject to modification, misuse,
negligence, accident, improper maintenance or repair by anyone other than SureFire.
“Fine Print” Warranty Limitation
     There is no other express warranty. SureFire LLC hereby disclaims any and all
implied warranties, including, but not limited to fitness for a particular purpose.
SureFire LLC shall not be liable for incidental, consequential, or special damages
arising out of, or in connection with product use or performance.
um_H11_5.B01
18300 Mt. Baldy Circle, Fountain Valley, CA 92708                 (714) 545-9444Caution
   The battery used in the light is very powerful. Be sure that the switch is not touching
anything when the light is stored. If the lamp is turned on while in a case or other container,
the lamp can overheat and damage the light or surrounding materials. Remove the battery or
unscrew the bezel far enough to prevent the lamp from turning on when stored.
   Do not use a 3 Volt Lamp Assembly in a 6 Volt system. The lamp will burn out Immedi-
ately!!! To identify a lamp assembly:  the 3 volt lamp has a Red label and is marked R30, the
6 volt has a Blue or Green label and is marked R60 or P60.
   If  it is necessary to dispose of any batteries, do not do so by fire, mutilation or by
disassembly, as this may cause toxic chemicals to be released.
WARNING
Lithium batteries can explode or cause burns if disassembled,
shorted, recharged or exposed to fire or high temperatures.
Please handle with care.