Surefire 302, 602 Tactical Light User Manual

							Model 302
602
 
Smith & Wesson Tactical Light
Users Manual
Smith & Wesson Pistols
 10 Series 10mm
with square trigger guards
Protected by US. Patents 4,777,754,  4,856,218 & 5,654,594
Revision B    11_1_95 
						

							Model 302 & 602 Tactical Light
Introduction
   The Model 302 & 602 Tactical Lights provide a rugged and reliable source of high intensity
light mounted below the barrel of the weapon. The light can be activated by pressing on the
Pressure Switch attached to the handgrip or by pushing forward on the Switch Actuator Plates on
the sides of the Housing.
Installation
  1. Remove the magazine from the weapon and inspect the weapon to be certain it is not loaded.
  2. Disassemble weapon far enough to remove slide stop.
  3. Position H02 Housing so that hole in side is aligned with slide stop hole on the frame.
  4. Install new Slide Stop.
  5. Reassemble weapon as necessary.
  6. Using the Hex Wrench provided in the Kit, tighten the Set Screw in the base of the Housing
      until it contacts the trigger guard then turn the set screw out 1/8 turn so as not to put tension
      on the Slide Stop. After firing 500 rounds the Set Screw may loosen, remove it and install the
      extra Set Screw provided in the Kit.*
  7. Select the location desired on the weapon for mounting the Pressure Switch.
  8. Using the Velcro provided in the Kit, remove the paper backing from the “loop” section
      of  Velcro and press in place on clean area. Wipe with alcohol first!
  9. Wipe the rear (flat) side of the Pressure Switch with alcohol to remove oil & dirt.
10. Remove the paper backing from the Velcro “hook” and press it in place on the rear side of
      the Pressure Switch.
11. Using Velcro, position the Pressure Switch on the weapon. Route the cable so that it does
       not interfere with the weapon operation.
12. Install the battery with the + terminal facing out.
13. Install the Lamp Module Assembly. Unit is now ready for use. 
						

							Surefire LLC 
						

							Kit Contents
! !! !
! H02 Housing & Slide Stop
! !! !
! L30 or L60 Lamp Module
! !! !
! DL123A or DL223AC Battery
! !! !
! Velcro Hook & Loop
! !! !
! Extra Set Screw
! !! !
! Hex Wrench
      !       !      !       !
      ! Alcohol Wipe
        
! !! !
! Users Manual
* Additional set screws are available in a Ten Pack, order P/N 12010-1.
Lamp Replacement
1. Unscrew Bezel from Lamp Module. Lift Lamp assembly out of Bezel.
2. Install replacement Lamp Assembly in Bezel and reassemble by
          screwing onto Lamp Housing until it is fully seated.
Battery Replacement
1. Unscrew Lamp Module from Housing and shake out old battery.
2. Install new battery with the + terminal facing out.
3. Reinstall Lamp Module.
WARNING
Lithium batteries can explode or cause burns if disassembled, shorted, recharged or exposed to
fire or high temperatures.  Please handle with care.
Model 302 & 602 Tactical Light 
						

							Model 302 & 602 Tactical Light
Repairs & Replacements
     To obtain repair or replacement call Customer Service at 800-828-8809 (toll free) or 714-545-
9444 and obtain a Return Authorization number (RA). Then pack the unit carefully and return (no
COD’s please) to:
     SureFire LLC
     Repairs Department, RA# ___
     18300 Mt. Baldy Circle
     Fountain Valley, CA 92708
SureFire will pay any reasonable shipping costs to return the unit to you.
Caution
   The battery used in the light is very powerful. Be sure
that the switch is not touching anything when the light is
stored. If the lamp is turned on while in a case or other
container, the lamp can overheat and damage the light or
surrounding materials. Remove the battery or unscrew
the bezel far enough to prevent the lamp from turning on
when stored.
   Do not use a 3 Volt Lamp Assembly in a 6 Volt sys-
tem. The lamp will burn out Immediately!!! To identify
a lamp assembly:  the 3 volt lamp has a Red label and is
marked R30, the 6 volt has a Blue or Green label and is
marked R60 or P60.
   If it is necessary to dispose of any batteries, do not do
so by fire, mutilation or by disassembly, as this may
cause toxic chemicals to be released.
Fine Print” Warranty Limitation
     There is no other express warranty. SureFire hereby disclaims any and all implied warranties,
including, but not limited to fitness for a particular purpose. SureFire shall not be liable for inciden-
tal, consequential, or special damages arising out of, or in connection with product use or perfor-
mance.
Protected by US. Patents 4,777,754,  4,856,218 & 5,654,594
Um_H02_5.B01
18300 Mt. Baldy Circle, Fountain Valley, CA 92708
(714) 545-9444