Surefire 301, 601 Tactical Light User Manual

							Model 301
601
Smith & Wesson Tactical Light
Users Manual
SMITH & WESSON PISTOLS
59 & 69 SERIES, MODEL 659 & 669
with Round trigger guards
Protected by US. Patents 4,777,754,  4,856,218 & 5,654,594 
						

							Model 301 & 601 Tactical Light
Introduction
   The Model 301 & 601 Tactical Lights provide a rugged and reliable source of high intensity
   light mounted below the barrel of the weapon. The light can be activated by pressing on the
   Pressure Switch attached to the handgrip or by pushing forward on the Switch Actuator Plates
   on the sides of the Housing.
Installation
  1. Remove the magazine from the weapon and inspect the weapon to be certain it is not loaded.
  2. Disassemble weapon far enough to remove slide stop.
  3. Position H01 Housing so that hole in side is aligned with slide stop hole on the frame.
  4. Install new Slide Stop.
  5. Reassemble weapon as necessary.
  6. Using the Hex Wrench provided in the Kit, tighten the Set Screw in the base of the
      Housing until it contacts the trigger guard then turn thesetscrew out 1/8 turn so as not
      to put tension on the Slide Stop. After firing 500 rounds the Set Screw may loosen,
      remove it and install the extra Set Screw provided in the Kit.*
  7. Select the location desired on the weapon for mounting the Pressure Switch.
  8. Using the Velcro provided in the Kit, remove the paper backing from the “loop” section of
      Velcro and press in place on clean area. Wipe with alcohol first!
  9. Wipe the rear (flat) side of the Pressure Switch with alcohol to remove oil & dirt.
10. Remove the paper backing from the Velcro “hook” and press it in place on the rear side
      of the Pressure Switch.
11. Using Velcro, position the Pressure Switch on the weapon. Route the cable so that it
      does not interfere with the weapon operation.
12. Install the battery with the + terminal facing out.
13. Install the Lamp Module Assembly
Unit is now ready for use. 
						

							SureFire, LLC 
						

							Model 301 & 601 Tactical Light
Kit Contents
! !! !
! H01 Housing & Slide Stop
! !! !
! L30 or L60 Lamp Module
! !! !
! DL123A or DL223AC Battery
! !! !
! Velcro Hook & Loop
! !! !
! Extra Set Screw
! !! !
! Hex Wrench
      !       !      !       !
      ! Alcohol Wipe
      !       !      !       !
      ! Users Manual
* Additional set screws are available in a Ten Pack, order P/N 12010-1.
Lamp Replacement
1. Unscrew Bezel from Lamp Module. Lift Lamp assembly out of Bezel.
2. Install replacement Lamp Assembly in Bezel and reassemble by screwing
    onto Lamp Housing until it is fully seated.
Battery Replacement
1. Unscrew Lamp Module from Housing and shake out old battery.
2. Install new battery with the + terminal facing out.
3. Reinstall Lamp Module.
WARNING
Lithium batteries can explode or cause burns if disassembled, shorted, recharged or exposed to
fire or high temperatures.  Please handle with care. 
						

							Caution
   The battery used in the light is very powerful. Be sure that the switch is
not touching anything when the light is stored. If the lamp is turned on
while in a case or other container, the lamp can overheat and damage the
light or surrounding materials. Remove the battery or unscrew the bezel
far enough to prevent the lamp from turning on when stored.
   Do not use a 3 Volt Lamp Assembly in a 6 Volt system. The lamp will
burn out Immediately!!! To identify a lamp assembly:  the 3 volt lamp
has a Red label and is marked R30, the 6 volt has a Blue or Green label
and is marked R60 or P60.
   If it is necessary to dispose of any batteries, do not do so by fire,
mutilation or by disassembly, as this may cause toxic chemicals to be
released.
Repairs & Replacements
     To obtain repair or replacement call Customer Service at 800-828-8809 (toll free) or 714-545-
9444 and obtain a Return Authorization number (RA). Then pack the unit carefully and return (no
COD’s please) to:
     SureFire LLC
     Repairs Department, RA# ___
     18300 Mt. Baldy Circle
     Fountain Valley, CA 92708
SureFire will pay any reasonable shipping costs to return the unit to you
Warranty
     SureFire warrants that its products will be free from defects in materials and
workmanship. SureFire Products will repair or replace (at its option), without charge,
any product or part which is found to be defective under normal use and service.
Such repair or replacement shall be the purchaser’s sole and exclusive remedy under
this warranty. This warranty does not include normal maintenance and services and
does not apply to any products or parts which have been subject to modification,
misuse, negligence, accident, improper maintenance or repair by anyone other than
SureFire.
“Fine Print” Warranty Limitation
     There is no other express warranty.  SureFire hereby disclaims any and all implied
warranties, including, but not limited to fitness for a particular purpose. SureFire shall
not be liable for incidental, consequential, or special damages arising out of, or in
connection with product use or performance.
Protected by US. Patents 4,777,754,  4,856,218