Studio Experience Projector Premier 50hd User Manual

Chapter 2 –  Connections
 12
C
ONNECTIONS
Turning On/Off
Follow these instructions to turn on projector.
1. Press the power switch on the rear panel to supply power to the projector.
2. Press the Power button on the control panel or remote control.
The fan starts running and the projector warms up. After the projector warms
up, (approximately 30 sec.) the image appears on the screen.
Press this switch to supply power to the projector.
Press the
power button. 

Chapter 2 –  Connections
13
C
ONNECTIONS
Turning Off
Warning!
Follow these procedures exactly as written to avoid damage to the
lamp and projector.
1. Press the power button on the control panel or remote to open the
Power Down Menu. Select Yes and and press Enter.  Alternately, you
can press the power button three times.
2. The lamp shuts off and the cooling fans continue to run for approxi-
mately two minutes to cool-down the lamp.  During this cool-down
period, the control panel LEDs flash.
3. After...

O
PERATION
Chapter 3
Operation
The projector can be operated using the top control panel or the remote control. This
chapter describes using the control panel and the remote control.
Operating the Control Panel and Remote Control
This section describes the functions available on the top control panel and the
remote control.
Zoom and Focus
The control panel has two dials to adjust the Zoom and Focus. 
Zoom
Rotate the zoom dial to change the size of the image.
Focus
Rotate the focus dial to focus the...

Chapter 3 –  Operation
15
O
PERATION
Input
Press the input button on the control panel to switch between the inputs. On the
remote control, press the number corresponding to the source mode you want:
– Input 1 – computer or DVI Mode
– Input 2 & 3 – component video 1&2
– Input 4 – S-Video/Composite Video
A screen at the bottom of the image shows which mode is currently selected. See
“Input Signals” on page 19 for more information.
Menu
Press this button to open the OSD menus. Refer to Chapter 4 for a full...

Chapter 3 –  Operation
 16
O
PERATION
Navigation Buttons
Press the up and down arrow buttons to scroll vertically through the menus. Press
the Enter button to open submenus and enter. Use the Exit   button to go to the pre-
vious menu.
The Remote Control
The remote control provides a convenient way to control the projector.
Installing Remote Control Batteries
Refer to the following illustrations and instructions on installing the remote control
batteries. 
1. Press the battery cover latch and pull the...

Chapter 3 –  Operation
17
O
PERATION
Setting Up the Projector
Follow these tips when setting up the projector.
Adjustment Peg
Use the adjustment peg on the base of the projector to adjust the height of the pro-
jected image.
Keystone Correction
Choose the keystone function in the
Geometry submenu to adjust the image
shape when the projector is at an angle
to the screen.
Adjusting the Projection Distance 
Position the projector perpendicular to
the screen with all feet flat to achieve
optimal image...

OSD M
ENUS
Chapter 4
OSD Menus
About the OSD Menus
You can configure the Premiere 50HD DLP Projector by using the On Screen Dis-
play (OSD) Menus. The OSD menus enable you to set advanced features of the pro-
jector, including setting the input signal type, brightness, contrast, sharpness, color
tint, and display language, among other things.
To access the OSD Menus, press the OSD Menu button on your remote control unit
or the control panel. You can navigate through the OSD Menus by using the Up,
Down,...

Chapter 4 –  OSD Menus
19
OSD M
ENUS
Input Signals
The Input Signals menu lets you specify
the signal type for the input into your pro-
jector. The following input signal types are
available.
Component 1&2 YPbPr
Select a YPbPr, SDTV, or HDTV compo-
nent input source.
Component 1&2 RGB
Select an RGB, RGBH+V, or RGBHV
input source.
PC
Use this option to select the computer input.
DVI
Use this option to select the DVI input. 
Composite
Use this option to select the Composite Video input source.
S-Video
Use...

Chapter 4 –  OSD Menus
 20
OSD M
ENUS
Color
Use this option to adjust the color saturation of the image. This item is only available
for video sources. The scale is from 0 to 100. The default setting is 50.
Tint
Use this option to adjust the tint of your image. Press 

Chapter 4 –  OSD Menus
21
OSD M
ENUS
Gamma Correction
Use this option to adjust the Gamma Correction
of your image. Default setting is gamma 2.2.
Gamma curves for all input sources can be set
using gamma user mode. Users can use the
Gamma Manager utility to adjust or create
gamma curves as desired. The Gamma Man-
ager can be found on the bundled CD installa-
tion kit or downloaded from our Web site. Refer
to Appendix C for more information on installing
and using the utility.
Gamma correction provides...