Studio Experience Projector Matinee 1hd User Manual

							21
Basic Operation
Keystone Adjustment
1
Press the KEYSTONE /button on the remote control or
select the Keystone in the Setting menu.  (Refer to page 42.)
The Keystone dialog box appears.
2
Correct keystone distortion by pressing the KEYSTONE /
button or the POINT UP/DOWN button.  Press the KEYSTONE
button or the POINT UP button to reduce the upper part of
image, and press the KEYSTONE button or the POINT
DOWN button to reduce the lower part.  
Reduce the upper width with the KEYSTONE 
button or the POINT UP button.  Reduce the lower width with the KEYSTONE 
button or the POINT DOWN button.  
If the projected image has keystone distortion after adjusting the lens shift, correct the image with the Keystone Adjustment.
•The arrows are white when there is  no
correction.
•The arrow disappears at the maximum
correction.
•The direction of the arrow being corrected turns
purple.
Press the NO SHOW button on the remote control to black out the
image.  To restore to normal, press the NO SHOW button again or
press any other button.
No Show Function
Message disappears after 4 seconds.
No show
Keystone Adjustment Hint
Use the Lens shift function first to move the screen for the quality of image before using the Keystone adjustment function.
Moving the screen with the Lens shift function produces a better image than keystone adjustment function.   
						

							22
Basic Operation
On-Screen Menu
MENU
POINT
RIGHT
BUTTON
ITEM
Display the on-screen menu by pressing the MENU button on
the top control or the remote control. A main menu appears.
1
Main menu
Select an item by pressing the POINT UP/DOWN button, and
activate the item that you have selected by the 
, ,or 
button.  
Select a menu from the main menu by pressing the POINT
UP/DOWN button, and press the POINT RIGHT button to
enter the sub-menu.  (The selected icon turns yellow.)
3
2
Sub-menu
Press the SELECT button to activate the item that you have
selected.  
SELECT BUTTON
Press the POINT LEFT button to go on or adjust values.  
POINT LEFT BUTTON
Press the POINT RIGHT button to go on or adjust values.  
POINT RIGHT BUTTON
WARNINGTEMP.
LAMPREPLACE
READY
LAMP
MENUINPUT
ON-OFF
SELECT
MENUSCREEN
SELECT
TOP CONTROL REMOTE CONTROL
Press the MENU button again to close the on-screen menu.  
4
Close the menu.
MENU button
The projector has the on-screen menu that provides a variety of adjustment and settings.   
						

							23
Basic Operation
Contents of Menus
VIDEO MENUS
COMPUTER MENUS
INPUT SOURCE SELECTION:select input source either Video [Auto, Video, S-Video, (Y-Pb/Cb-Pr/Cr)] or
Computer.  (Refer to page 24, 25.)
VIDEO SYSTEM SELECTION:select Video system from AUTO, PAL, SECAM, NTSC, NTSC4.43, PAL-M,
PAL-N, 1080i, 1035i, 720p, 575p, 480p, 575i, 480i.  (Refer to page 26.)
IMAGE LEVEL SELECTION:select image level from Standard, Cinema, and Image 1 ~ 4.  (Refer to page
27.)
IMAGE LEVEL ADJUSTMENT:adjust Contrast / Brightness / Color / Tint / Color temp. / White balance (R/G/B) /
Sharpness / Gamma / Auto grayscale / Auto fleshtone.  (Refer to page 28, 29.)
SCREEN SIZE ADJUSTMENT:set the screen size from Full, Zoom, or Normal.  (Refer to page 30.)
SETTING:change various settings; Language, Keystone, Blue back, Display, Menu position, Logo, Ceiling,
Rear, Power management, Power off confirmation, Lamp mode, Remote control, and Lamp
counter reset.  (Refer to page 42.)
INPUT SOURCE SELECTION:select input source either Computer or Video [Auto, Video, S-Video, (Y-Pb/Cb-
Pr/Cr)].  (Refer to page 31.)
COMPUTER SYSTEM SELECTION:select computer system available.  (Refer to page 32.)
IMAGE LEVEL SELECTION:select image level from Standard, Real, and Image 1 ~ 4.  (Refer to page 38.)
IMAGE LEVEL ADJUSTMENT:adjust Contrast / Brightness / Color temp. / White balance (R/G/B) / Sharpness /
Gamma / Auto grayscale / Auto fleshtone.  (Refer to page 39, 40.)
SCREEN SIZE ADJUSTMENT:set the size from Normal, Full, True, and Digital zoom.  (Refer to page 41.)
SETTING:change various settings; Language, Keystone, Blue back, Display, Menu position, Logo, Ceiling,
Rear, Power management, Power off confirmation, Lamp mode, Remote control, and Lamp
counter reset.  (Refer to page 42.)
COMPUTER ADJUSTMENT:select Auto PC Adj. or adjust Fine sync, Total dots, Horizontal, Vertical, Current
mode, Clamp, Display area, Display area H, Display area V, Full screen, and
use Reset, Mode free, and Store.  (Refer to page 34-37.) 
						

							24
Video Input
Input Source Selection (Direct Operation)
You can select Video input or Computer input with the INPUT button.
(The input source that was selected last is selected when the projector
is turned on.)  
If the projector cannot reproduce proper video source, select correct
input source through menu operation on the next page.INPUT button
Video
Computer
WARNINGTEMP.
LAMPREPLACE
READY
LAMP
MENUINPUT
ON-OFF
SELECTNO SHOW
IMAGE
INPUT
1
2
IMAGEAUTO
VIDEO
VIDEO
TOP CONTROL REMOTE CONTROL
Press AUTO, VIDEO, S-VIDEO, or COMPO button on the remote
control according to video input.  
*It is convenient  for you to select AUTO as the projector automatically
detects incoming video signal, and adjust itself to optimize its
performance.
KEYSTONE
NO SHOW
IMAGE
INPUT
1
2
3
4
IMAGE
AUTO
VIDEO
S-VIDEO
COMPOCOMPONENT
VIDEO
REMOTE CONTROL
INPUT BUTTON
AUTO / VIDEO / S-VIDEO / COMPO BUTTON
INPUT button
AUTO / VIDEO / S-VIDEO / COMPO button
When selecting AUTO, the projector automatically
detects incoming video signal, and adjusts itself to
optimize its performance.  The projector selects
connection in the following order:
1st Y-Pb/Cb-Pr/Cr
2nd S-VIDEO
3rd VIDEO
The Y-Pb/Cb-Pr/Cr has priority over the S-VIDEO.  The
S-VIDEO has priority over the VIDEO. AUTO
When video input signal is connected to VIDEO, select
Video.VIDEO
When video input signal is connected to S-VIDEO, select
S-Video.S-VIDEO
When video input signal is connected to Y-Pb/Cb-Pr/Cr,
select COMPO.COMPO
RGB Scart Input
To select RGB Scart 21-pin video input through the computer input
terminal, follow the procedures described at the section Input Source
Selection on page 31. 
						

							25
Video Input
Input Source Selection (Menu Operation)
Press the MENU button, and the main menu appears.  Select
the Input Source Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.  
Choose Video with the POINT UP/DOWN button and press
the POINT RIGHT button.  The source selection menu
appears.  
1
2
Source Selection menu (VIDEO)
Input Source Selection menu
Move the pointer to the source that you want to select with the
POINT UP/DOWN button, and press the SELECT button.  Close
the source selection menu.  
3
pointer
Close the source selection menu.
Input Source Selection menu 
						

							26
Video input
Video System Selection menu (VIDEO / S-VIDEO)Press the MENU button, and the main menu appears.  Select
the Video System Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
Choose the system that you want to select with the POINT
UP/DOWN button, and then press the SELECT button to
activate the item. 
1
2
If the projector cannot reproduce proper video image, select a specific
system among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
The projector automatically detects the incoming video system, and
adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, select a specific
component video system among 480i, 575i, 480p, 575p, 720p, 1035i,
and 1080i.
Auto
COMPONENT VIDEO SIGNAL FORMAT
Video System Selection (Video / S-Video)
Video System Selection (Y-Pb/Cb-Pr/Cr)
The projector automatically detects the incoming video system, and
adjusts itself to optimize its performance.
However, when video system is PAL-M or PAL-N, select either PAL-M
or PAL-N manually.
Auto
Video System Selection menu 
Close the Video System Selection menu.
Press the MENU button, and the main menu appears.  Select
the Video System Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
Video System Selection menu (Y-Pb/Cb-Pr/Cr)
Choose the system that you want to select with the POINT
UP/DOWN button, and then press the SELECT button to
activate the item. 
2
displays the
selected
system. 
						

							27
Video Input
Image Level Selection (Menu Operation)
Press the MENU button, and the main menu appears.  Select
the Image Level Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the level that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.
Image Level Selection menu
Normal picture adjustment preset on this projector.
Standard
Picture level adjusted for the picture with fine tone.
Cinema
User preset picture adjustment in Image Level Adjustment menu (p28,
29).
IMAGE 1~4
Image Level Selection
menu
Image Level Selection (Direct Operation)
Select the image level from Standard, Cinema, Image 1, Image 2,
Image 3, and Image 4 by pressing the IMAGE button on the remote
control.  (See the next section Image Level Selection (Menu
Operation) about each item.) 
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
KEYSTONE
NO SHOW
IMAGE
INPUT
1
2
3
4
IMAGE
AUTO
VIDEO
S-VIDEO
COMPOCOMPONENT
VIDEO
IMAGE 1-4 button
IMAGE button
The level being selected.
Close the Image Level Selection menu. 
						

							28
Video Input
Press the MENU button, and the main menu appears.  Select
the Image Level Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the item that you want to adjust with the POINT
UP/DOWN button, and then press the POINT LEFT/RIGHT
button to adjust each item.  The items displayed in a line can be
adjusted while you see the change of the image.  Press the
SELECT button to finish adjusting an item.  The on-screen menu
returns to the sub-menu.  Image Level Adjustment menu
Image Level Adjustment
Press the
SELECT button
at this icon to
display other
items.
Press the SELECT button at this
icon to close the item.
Image Level Adjustment
menu
3
To store the adjustment data, select Store with the POINT
UP/DOWN button and press the POINT RIGHT button. 
Select the Store.
4
Choose one of the positions from Image Level 1 to 4 that you
want to store with the POINT UP/DOWN button, and press the
SELECT button.  Select Yes with the SELECT button and
close the menu by pressing the SELECT button at Quit.  
NOTE
All the items on the next page can be memorized in Image 1-4. 
Reset
To reset to previous settingsl, select Reset with the POINT
UP/DOWN button and press the POINT RIGHT button.  Select
Yes with the SELECT button.   
						

							29
Video Input
Press the POINT LEFT button to decrease contrast and the POINT RIGHT button to increase contrast.  (From 0 to 63.)
Press the POINT LEFT button to adjust image darker and the POINT RIGHT button to adjust image brighter.  (From 0 to 63.)
Contrast
Brightness
Press the POINT LEFT button or the POINT RIGHT button to obtain better balance of contrast.  (From 0 to 15.)
Gamma
Press the POINT LEFT button to lighten color and the POINT RIGHT button to deepen color.  (From 0 to 63.)
Press the POINT LEFT button or the POINT RIGHT button to obtain proper color.  (From 0 to 63.)
Color
Tint
Press the POINT LEFT button to soften the image and the POINT RIGHT button to sharpen the image.  (From 0 to 15.)
Sharpness
Press the POINT LEFT button to lighten red tone and the POINT RIGHT button to deepen red tone.  (From 0 to 63.)
White balance (Red)
Press the POINT LEFT button to lighten green tone and the POINT RIGHT button to deepen green tone.  (From 0 to 63.)
White balance (Green)
Press the POINT LEFT button to lighten blue tone and the POINT RIGHT button to deepen blue tone.  (From 0 to 63.)
White balance (Blue)
NOTE : Tint cannot be adjusted when the video
system is PAL, SECAM, PAL-M or PAL-N.
When this function is ON, it automatically enhances contrast of bright and dark part of image.
When this function is ON, it produces more vivid image according to image condition. 
Auto grayscale
Auto fleshtone
The items that you can adjust are the following:
Color temp.
Press the POINT LEFT button or the POINT RIGHT button for Color temp. level that you want to select. (XLow, Low, Mid, or
High) 
Store the adjustment data.
Reset all adjustment to their previous levels.  (The Reset does not work for the stored data.)
Reset
Store
Quit
Close the Image Level Adjustment menu. 
						

							30
Video Input
This projector has a picture screen resize function, which enables you to display the desirable image size.
NOTE :  The Screen Size Adjustment cannot be operated when
“720p,” “1035i,” or “1080i” is selected in the Video
System Selection menu (p26).
Provides an image to fit screen size (16 : 9 aspect ratio) by expanding
the image width and height uniformly.  This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black bar
on the top and bottom edges) at wide video aspect of 16 : 9.
Zoom
Provides an image at the normal video aspect ratio of 4 : 3.
Normal
Press the MENU button, and the main menu appears.  Select
the Screen Size Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the item that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.  Screen Size Adjustment menuPress the
SELECT button
at this icon to
activate the
item.
Screen Size Adjustment menu
Provides an image to fit width of screen by expanding the image width
uniformly.  This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select the Full on this Screen Size Adjustment menu
to provide better quality.
Full
Screen Size Adjustment (Menu Operation)
Screen Size Adjustment (Direct Operation)
Select the screen size among Full, Zoom, and Normal by pressing the
SCREEN button on the remote control.  (See the next section Screen
Size Adjustment (Menu Operation) about each item.) 
SCREEN button
Full
Zoom
Normal
MENUSCREEN
AUTO PC ADJ.
AUTOLIGHT
SELECT
SCREEN button
Close the Screen Size Adjustment menu.
Full
Zoom
Normal