Stoves Q900 User Guide

you are asked to enter in an end time, or 
when you would like the oven to switch 
itself off.
to set the time of day
•	Press the Up and Down buttons 
together for a few seconds, and 
release.
•	 The	‘	 •’	in	between	the	numbers	on	
the	LED	Display	will	begin	to	flash.
•	 While	the	‘	 •’	is	flashing	it	is	possible	
to adjust the time using the Up and 
Down buttons. once the time has 
been set, allow approximately 30 
seconds before using any of the other 
timer functions. This ensures that the 
time will...

semi-automatic cooking
There are two types of semi automatic 
cooking available on this appliance.
The oven must be switched on, and in use 
to use either of these functions success-
fully.
The Duration method allows you to set the 
oven	for	a	specific	length	of	time.	If	a	dish	
needed 2 hours to cook, then it would be 
possible for you to set the oven to turn off 
2 hours later. This allows you to be sure 
that your food will be cooked for a set 
length of time and no longer.
The End Time method allows...

seMI-aUtoMatIc cookInG
the duration method
•	Press	the	Function	button	twice,(1)	
which will skip past the Minute 
Minder.
•	 The	LED	display	will	flash	the	word	
‘dur’,	(2)	and	the	‘A’	will	flash	on	the	
left hand side of the display.
•	 Use the Up and Down buttons to set 
the length of time you want to cook 
for.(3)	This	must	be	done	within	5	
seconds or the time of day will show 
again.
once this is done the oven will automati -
cally switch off once the time has elapsed, 
and the alarm will sound.
To...

fUlly aUtoMatIc cookInG (ex-
aMple)
This programming method is best suited 
for when a delayed start time is required. 
Unlike the semi automatic methods this 
requires both the duration and the end 
time to be entered. The timer will work 
out the start time and begin cooking.
•	 Press the function button twice to 
select the length of time your food 
will	need.	(7)
•	 The	‘A’	on	the	left	hand	side	will	flash	
and	the	‘dur’	message	will	flash	up.	
(8)
•	 Using the Up and Down buttons set 
the time you...

the touch control programmer
There are three touch control icons for 
this timer - the table below shows you 
what the symbols look like, depending on 
the model type, & their functions.
Note - some functions require you to 
‘touch & hold’ an icon for a few seconds, 
whilst others require you to just ‘touch’ 
the icon without holding.
Sym-
bolSym
-
bol
What is it?
     
-
   Down/minus
Used to decrease 
cook / end time, re-
move minutes from 
the minute minder 
and adjust the time 
of day. Also for lis-...

setting the time of day
Touch	&	hold	the	centre	(function)	icon	for	
a	few	seconds	until	the	●	symbol	between	
the	numbers	on	the	LED	display	flashes.
While	the	●	symbol	is	flashing,	you	can	
adjust the time of day by touching the 
plus	&	minus	icons.	Please	note:	the	hours	
& minutes adjust quickly.
Important - once the time of day has 
been set, allow approximately 30 seconds 
before using any of the other programmer 
functions. This ensures that the time of 
day will remain correct.
setting an alarm...

Use the plus & minus icons to select the 
time the oven is required to switch off.
once this is done the oven will switch 
itself off at the pre-selected time. To turn 
the alarm off, touch any icon.
To cancel the semi-automatic programme 
at any time, touch the plus & minus icons 
together.
fully automatic cooking
This function allows the cooker to switch 
on & off automatically. It requires both the 
duration & the end time to be entered. 
The timer will work out the start time & 
begin cooking.
Touch...

UsInG tHe pRoGRaMMeR - toUcH
1.0 overview of symbols & functions:
Display symbols:
Minute minder
cooking time
End of cooking time
Time of day
child lock
cooking pot
Automatic mode
Manual mode
Pyrolysis	mode	(OPTIONAL)
Acoustic signal
7-segment display
Max. adjustable minute minder
Max. adjustable cooking time
Display	hours:minutes
Display	minutes:seconds
1.1 Manual mode
The programmer remains in MANUAl mode if no cooKING TIME or END of cooKING 
TIME is selected & the symbol 
 is displayed. The TIME of...

UsInG tHe pRoGRaMMeR - toUcH
2.0 touch control
  Select a function
 
   Plus - increase time or volume
 
   Minus - decrease time or volume
2.1 touch controls 
  
Touching the 
 &  symbols momen-
tarily increases or decreases the time by 
one minute (or the volume of the AcoUS -
TIC	SIGNAL	by	one	step).
Touching the & symbols permanentlly 
increases or decreases the speed of time 
setting automatically.
2.2 touch control 
Touching the FUNcTIoN symbol 
momentarily, the next following function is 
chosen....

UsInG tHe pRoGRaMMeR - toUcH
3.0 fUnctIons
3.1 start of function
When a function is selected & the time 
or acoustic volume is set, the chosen 
function	will	start	automatically	five	
seconds after setting.
The display shows the current TIME of 
DAY, except when the MINUTE MINDEr is 
active. In this case, the display shows the 
remaining time of the MINUTE MINDEr.
3.2 power on/initial operation
After connecting the appliance to the 
mains, the display shows the default TIME 
of DAY 
	flashing.
In the...