Stihl Fc 56 C Manual

{
STIHL FC 56 C
WARNING
Read Instruction Manual thoroughly 
before use and follow all safety 
precautions – improper use can 
cause serious or fatal injury.
ADVERTENCIA
Antes de usar la máquina lea y siga 
todas las precauciones de 
seguridad dadas en el manual de 
instrucciones – el uso incorrecto 
puede causar lesiones graves o 
mortales.
,QVWUXFWLRQ0DQXDO
0DQXDOGHLQVWUXFFLRQHV 

Instruction Manual
1 - 39
Manual de instrucciones
40 - 83 

Original Instruction Manual Printed on chlorine-free paper
Printing inks contain vegetable oils, paper can be recycled. © ANDREAS STIHL AG & Co. KG, 2017
0458-545-8621-E. VA0.F17. 
0000006736_008_GB
FC 56 C
English
1
{This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process 
with electronic systems.
Contents
Allow only persons who fully understand 
this manual to operate your edger.
To receive maximum performance and 
satisfaction...

FC 56 C
English
2
Pictograms
The meanings of the pictograms 
attached to or embossed on the 
machine are explained in this manual.
Depending on the model concerned, the 
following pictograms may be on your 
machine.
Symbols in Text
Many operating and safety instructions 
are supported by illustrations.
The individual steps or procedures 
described in the manual may be marked 
in different ways:
NA bullet marks a step or procedure.
A description of a step or procedure that 
refers directly to an...

FC 56 C
English
3
WARNING
As more fully explained later in these 
Safety Precautions, to reduce the risk of 
personal injury, make sure your unit is 
equipped with the proper handle, 
harness and deflector. Use only cutting 
attachments that are specifically 
authorized by STIHL for use on your FC 
model.
Have your STIHL dealer show you how 
to operate your power tool. Observe all 
applicable local safety regulations, 
standards and ordinances.
WARNING
Do not lend or rent your power tool 
without the...

FC 56 C
English
4 These conditions reduce the hand's 
ability to feel and regulate temperature, 
produce numbness and burning 
sensations and may cause nerve and 
circulation damage and tissue necrosis.
All factors which contribute to 
whitefinger disease are not known, but 
cold weather, smoking and diseases or 
physical conditions that affect blood 
vessels and blood transport, as well as 
high vibration levels and long periods of 
exposure to vibration are mentioned as 
factors in the development...

FC 56 C
English
5 Avoid loose-fitting jackets, scarfs, 
neckties, jewelry, flared or cuffed pants, 
unconfined long hair or anything that 
could become caught on branches, 
brush or the moving parts of the unit. 
Secure hair so it is above shoulder level.
THE POWER TOOL
For illustrations and definitions of the 
power tool parts see the chapter on 
"Main Parts."
WARNING
Never modify this power tool in any way. 
Only attachments supplied by STIHL 
and expressly approved by STIHL for 
use with the...

FC 56 C
English
6
WARNING
Fueling Instructions
WARNING
To reduce the risk of serious injury from 
burns, never attempt to refuel the unit 
until it has been completely removed 
from the operator.
WARNING
Fuel your power tool in well-ventilated 
areas, outdoors. Always shut off the 
engine and allow it to cool before 
refueling. Gasoline vapor pressure may 
build up inside the fuel tank depending 
on the fuel used, the weather conditions 
and the tank venting system.
In order to reduce the risk of burns...

FC 56 C
English
7 NTo return the cap to the open 
position for installation, turn the cap 
(with the grip up) until it drops fully 
into the tank opening. Next, twist the 
cap counterclockwise as far as it will 
go (approx. 1/4 turn) – this will twist 
the base of the cap into the correct 
position. Then, twist the cap 
clockwise, closing it normally.
NIf your cap still does not tighten 
properly, it may be damaged or 
broken; immediately stop use of the 
unit and take it to your authorized 
STIHL dealer...

FC 56 C
English
8
WARNING
An arrow on the deflector shows the 
correct direction of rotation of the cutting 
blade.
The arrow on the deflector must always 
face away from you, so that cuttings and 
other debris will be diverted away from 
the machine and your position (see 
chapter "Working Techniques".)
Adjust carrying harness and hand grip to 
suit your size before starting work. The 
machine should be properly balanced as 
specified in your instruction manual for 
proper control and less...