Stiga SWEEPER 13 0920 12 Instructions Manual

							
TRANÅS - SWEDEN
(10133) 1319-1835-01
MADE IN FINLAND BY KOVA
Art. No:  13-0920-12Type:  VA501 
						

							
GB
SAFETY REGULATIONS
These regulations should be read carefully by everyone using the machine\
.
Tell everyone who wants to use the sweeper what the risks involved are, \
and how accidents can be avoided.
Keep hands and feet away from the rotating parts of the machinery.
The fewer people there are near the machine, the less risk there is of a\
nyone being hurt by stones or other
hard objects thrown out by the brushes.
Keep children clear of the working area of the machine at all times. Hav\
e another adult person keep an eye
on the children.
Be careful when reversing. Look back before and during reversing to chec\
k for obstacles. Beware of small
children.
Do not drive too near ditches or high kerbs. The machine may overturn if\
 a wheel goes over the edge or a
shoulder gives away .
When clearing snow, never point the sweeper in the direction of people, \
animals, windows etc. Stones may
be hidden in the snow, and may be thrown out with considerable force.
Always switch off the engine before cleaning the sweeper, or carrying ou\
t repairs, adjustments or
inspections.
Tighten all nuts and screws to ensure that the machine is in a safe work\
ing condition.
Always use original spare parts. Using nonoriginal parts may involve a r\
isk of damage, even if they fit the
machine.
ASSEMBLY
1. Dismantle the mower deck. Remove the drive belt for the mower deck, a\
nd fit the belt supplied with the
sweeper.
2 .  Remove the drive belt for the mower deck by pulling it over the central \
tension roller and spring. Fit the
belt supplied with the sweeper.
3 . Fit the front support wheel bracket onto the gearbox housing using the\
 bolts and nuts C provided (fig  1).
4 . Remove the screw D and raise the lever. Then fit the screw back in pos\
ition, so that it  passes through the
bracket and the adjusting lever (figs  2 and  3).
5.  Fit the sweeper frame onto the machine. The frame is supplied with the b\
olts and nuts already in their
holes (fig  4).
6 . Slide the spindle of the sweeper into the frame (fig  5).
7 . Fit the chain to the lift arm (fig  6).
8 . The lateral inclination of the sweeper can be adjusted with the help o\
f the adjusting bolts and nuts G
(fig  7).
USING THE MACHINE
BEFORE USE
The gearbox is supplied filled with oil.
Check the oil level before using the sweeper. The sweeper should be stan\
ding level.
When the oil needs replenishing, use SAE 30 or SAE 1OW30. The gearbox ho\
lds 0.4 litres.
Remove the filler plug H, and check that the oil reaches the edge of the\
 filling hole (fig  8).
SETTING THE GROUND PRESSURE
The ground pressure, i.e. the lie of the brushes against the ground, can\
 be set with the help of the support
wheels (fig  9) and the adjusting nut on the lift chain J (fig  6). 
						

							
Never use the sweeper with the ground pressure set too high, as this wil\
l result in increased wear on the
brushes.
NOTE! lf the front support wheel is to be filled with air it must be dis\
mantled.
SETTING THE BRUSHES DIAGONALLY
The sweeper can be set in any of three positions: diagonally to the righ\
t or left, or at right angles to the
direction of travel. Press the adjusting lever first to the left, and th\
en pull it either forwards or backwards
(fig 1
0).
OPERATING TIPS
When the sweeper is to be used for clearing snow, check the area to be c\
leared, and remove all stones and
other foreign objects, before the first fall of snow.
To obtain the best results, clear snow as soon as possible after it has \
fallen. lf there is a wind blowing, snow
or sand clearing operations should be carried out in the same direction \
as the wind.
To avoid throwing out too much dust when clearing sand, wet the surface \
to be cleared before starting
clearing operations.
It is usually a good idea to operate with the sweeper brushes angled tow\
ards the appropriate side.
Where the distance to or from the area to be cleared is a long one, set \
the sweeper brushes at right angles
to the direction of travel, and disconnect the power take-off.
AFTER USE
Always clean the sweeper after use. This ensures a longer life, and a pr\
oper function of the sweeper.
MAINTENANCE
REPLACING THE BRUSHES
1. Unfasten the screw L and pull the brush off the shaft (fig 1 1).
2. Unscrew the  two screws M in the  plate .
3. Remove the worn brush rings and replace them with new ones.
The ring with the angled brush should be fitted next to the gearbox hous\
ing, with the brush angled in
towards the gearbox housing.
To obtain the best results, replace all brush rings at the same time .
SERVICE
Authorized service work shops will carry out repairs and service under g\
uarantee. They use original spare
parts.
Do you prefer to carry out simple repairs yourself? Always use original \
spare parts. They fit the machine
without the necessity for any modifications, and make the job easier.
Spare parts are obtainable from authorized service work shops.
ACCESSORIES
Dust shield, for fitting on the front edge of the guard shield, art. no.\
 13-1936 fits Park and art. no. 13-1937
fits Villa. 
						

							
TRANÅS - SWEDEN
Art. No:  13-0920-12
D
450 mm
Max
L 1
850 mm
1 kg
±17º260 rpm
T-20411
 
61,0 kg 
						

							
M8x45
13 mm
1.
C
Art. No:  13-1933-14
3.
2.
DM6x40
10 mm 
						

							
M10x35
4.
Art. No:  13-0920-12
17 mm
D
5.
M10x40
17 mm
J
6. 
						

							
Art. No:  13-0920-12
G
M10x30
17 mm
7.
H
8.
9. 
						

							
Art. No:  13-0920-12
1
2
2
10.
11.
L M 
						

							
Addendum Stiga Villa 2001-
1. 2.4.
3.
8211-1230-01
STOP 
						

							
Ismo Forsström
INTYGS
Tillverkare: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, försäkrar härmed att maskintyp
VA501 är i överenstämmelse med maskindirektivet 89/392/EEC,
91/368/EEC, 93/44/EEC med särskilda hänvisningar till direktivets
Annex 1 om väsentliga hälso och säkerhetskrav i samband med
konstruktion och tillverkning.
Utfärdat i Halikko 2002
TODISTUSFIN
Valmistaja: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, vakuuttaa, että konetyyppi VA501 
on konedirektiivin 89/392/EEC, 91/368/EEC, 93/44/EEC mukainen
huomioden erityisesti oleelliset terveys- ja turvallisuusvaatimukset,
jotka koskevat koneiden suunnittelua ja rakennetta.
Laadittu Halikossa 2002
BESCHEINIGUNG D
Hersteller: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, bestätigt hiermit, daß die maschine
vom Typ VA501 mit den Mashinenrichtlinien 89/392/EEC,
91/368/EEC, 93/44/EEC unter besonderem Hinweis auf ANNEX 1 der
Richtlinie über die wichtigsten Gesundheits- und
Sicherheitsanforderungen im  Zusammenhang mit Konstruktion und
Herstellung, übereinstimmt. 
Ausgestellt in Halikko 2002
BEVISDK
Fremstiller: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, forsikrer hermed, at maskinen af type
VA501 er i överenstemmelse med Maskindirektiv 89/392/EEC,
91/368/EEC, 93/44/EEC med særlig henvisning til direktivets Anneks 1
om væsentlige sundheds- og sikkerhedskrav i forbindelse med
konstruktion och fremstilling.
Udfærdiget i Halikko 2002
ATTEST  N
Produsent: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, forsikrer herved at maskinen av type
VA501 er i överenstemmelse med EUs Maskindirektiv 
89/392/EEC, 91/368/EEC, 93/44/EEC med særskilt henvisning til 
direktivets vedlegg 1 om vesentlige helse- og sikkerhetskrav i forbindel\
se
 med konstruksjon och produksjon.
Utferdiget i Halikko 2002
ATTESTATION F
Fabricant: KONEPAJA A. VANNE, KOVA, Veistämöntie 16, FIN-24800
HALIKKO, FINLAND, atteste par la présente que la machine de type
VA501 est conforme aux Directives Machines 89/392/EEC,
91/368/EEC, 93/44/EEC avec une référence particuliére à i A\
nnexe 1
des directives, consernant les exigences principales en matieré de
santé et de sécurité au niveau de la construction et de la fabr\
ication.
Fait à Halikko en 2002
CERTIFICATEGB
Manufacturer: KONEPAJA A. VANNE, KOVA, Veistämöntie 16,
FIN-24800 HALIKKO, FINLAND, hereby certifies that the machine of
type VA501 conforms to Machine Directive 89/392/EEC,
91/368/EEC, 93/44/EEC with special reference to Annexe 1 of the
directive concerning essential health and safety requirements in
relation to design and manufacture.
Issued at Halikko 2002