Steinberg UR824 Getting Started Manual

							EN
DE
FR
ES
JAIT
USB AUDIO INTERFACE 
						

							2UR824 Getting Started
1. IMPORTANT NOTICE: 
DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the 
instructions contained in this manual, meets FCC 
requirements. Modifications not expressly 
approved by Yamaha may void your authority, 
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to 
accessories and/or another product use only high 
quality shielded cables. Cable/s supplied with this 
product MUST be used. Follow all installation 
instructions. Failure to follow instructions could void 
your FCC authorization to use this product in the 
USA.
3. NOTE: This product has been tested and found to 
comply with the requirements listed in FCC 
Regulations, Part 15 for Class “B” digital devices. 
Compliance with these requirements provides a 
reasonable level of assurance that your use of this 
product in a residential environment will not result 
in harmful interference with other electronic 
devices. This equipment generates/uses radio 
frequencies and, if not installed and used according 
to the instructions found in the users manual, may 
cause interference harmful to the operation of other 
electronic devices. Compliance with FCC  regulations does not guarantee that interference 
will not occur in all installations. If this product is 
found to be the source of interference, which can 
be determined by turning the unit “OFF” and “ON”, 
please try to eliminate the problem by using one of 
the following measures:
Relocate either this product or the device that is 
being affected by the interference. 
Utilize power outlets that are on different branch 
(circuit breaker or fuse) circuits or install AC line 
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 
ohm ribbon lead, change the lead-in to co-axial 
type cable.
If these corrective measures do not produce 
satisfactory results, please
 contact the local retailer 
authorized to distribute this type of product. If you 
can not locate the appropriate retailer, please 
contact Yamaha Corporation of America, Electronic 
Service Division, 6600 Orangethorpe Ave, Buena 
Park, CA90620
The above statements apply ONLY to those 
products distributed by Yamaha Corporation of 
America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : USB AUDIO INTERFACE Model Name : UR824
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference receiv ed including interference that may cause undesired 
operation.
See user manual instructions if interf erence to radio reception is suspected.
(FCC DoC)
(class b korea) 
						

							UR824 Getting Started3
English
Contents
PRECAUTIONS ............................................ 4
Introduction ................................................. 7
A Message From the Development Team......... 7
Included Accessories ........................................ 7
How to Read the Manual ................................... 9
Panel Controls and Terminals ................. 10
Rear Panel ...................................................... 10
Front Panel ...................................................... 11
Setup .......................................................... 12
1. Setting up the Power  Supply ....................... 12
2. Installing Cubase AI .................................... 13
3. Installing TOOLS for UR824........................ 14
4. Downloading the Licenses (Activation) ....... 16
Basic Operations ...................................... 17
Introduction...................................................... 17
Connection Example ....................................... 17
Configuring Audio Driver Settings on the 
DAW Software ................................................. 17
Troubleshooting........................................ 19
Appendix.................................................... 21
Contents of the Operation Manual ..... ............. 21
Uninstalling TOOLS for UR 824 ....................... 21
Specifications .................................................. 23 
						

							4UR824 Getting Started
EnglishPRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
 WARNING
Always follow the basic precautions listed below 
to avoid the possibility of  serious injury or even 
death from electrical shock, short-circuiting, 
damages, fire or other hazards. These 
precautions include, but are not limited to, the 
following:
• Do not place the power cord near heat sources such as 
heaters or radiators, and do not excessively bend or 
otherwise damage the cord, place heavy objects on it, or 
place it in a position where anyone could walk on, trip 
over, or roll anything over it.
• Only use the voltage specified as correct for the device.  The required voltage is printed on the name plate of the 
device.
• Use the specified adaptor (PA-300C or an equivalent  recommended by Yamaha) only. Using the wrong adaptor 
can result in damage to the device or overheating.
• Use only the supplied power cord/plug.
• Check the electric plug periodically and remove any dirt or  dust which may have accumulated on it.
• This device contains no user-serviceable parts. Do not  open the device or attempt to disassemble the internal 
parts or modify them in any way. If it should appear to be 
malfunctioning, discontinue use immediately and have it 
inspected by qualified Yamaha service personnel. • Do not expose the device to rain, use it near water or in 
damp or wet conditions, or place on it any containers 
(such as vases, bottles or glasses) containing liquids 
which might spill into any openings. If any liquid such as 
water seeps into the device, turn off the power immediately 
and unplug the power cord from the AC outlet. Then have 
the device inspected by qualified Yamaha service 
personnel.
• Never insert or remove an electric plug with wet hands.
• Do not put burning items, such as candles, on the unit. A  burning item may fall over and cause a fire.
• When one of the following problems occur, immediately  turn off the power and disconnect the electric plug from the 
outlet. Then have the device inspected by Yamaha service 
personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
• If this device or the AC power adaptor should be dropped or  damaged, immediately turn off the power, disconnect the 
electric plug from the outlet, and have the device inspected 
by qualified Yamaha service personnel.
Power supply/AC power adaptor
Do not open
Water warning
Fire warning
If you notice any abnormality
PA_en_1  1/2 
						

							UR824 Getting Started5
English
 CAUTION
Always follow the basic precautions listed below 
to avoid the possibility of physical injury to you or 
others, or damage to the device or other 
property. These precautions include, but are not 
limited to, the following:
• Do not cover or wrap the AC power adaptor with a cloth or 
blanket.
• When removing the electric plug from the device or an  outlet, always hold the plug itself and not the cord. Pulling 
by the cord can damage it.
• Remove the electric plug from the outlet when the device is  not to be used for extended periods of time, or during 
electrical storms.
• Do not place the device in an unstable position where it  might accidentally fall over.
• Do not block the vents. This device has ventilation holes at  the top/sides to prevent the internal temperature from 
becoming too high. In particular, do not place the device 
on its side or upside down. Inadequate ventilation can 
result in overheating, possibly causing damage to the 
device(s), or even fire.
• Do not place the device in a location where it may come  into contact with corrosive gases or salt air. Doing so may 
result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet  you are using is easily accessible. If some trouble or 
malfunction occurs, immediately turn off the power and 
disconnect the plug from the outlet. Even when the power 
is turned off, electricity is still flowing to the product at the 
minimum level. When you are not using the product for a 
long time, make sure to unplug the power cord from the 
wall AC outlet.
• Before connecting the device to other devices, turn off the  power for all devices.
Before turning the power on or off for all devices, set all 
volume levels to minimum. • Remove the power plug from the AC outlet when cleaning 
the device.
• Do not insert your fingers or hands in any gaps or  openings on the device (vents, etc.). 
•  Avoid inserting or dropping foreign objects (paper, plastic,  metal, etc.) into any gaps or openings on the device (vents, 
etc.) If this happens, turn off the power immediately and 
unplug the power cord from the AC outlet.
Then have the device inspected by qualified Yamaha 
service personnel.
• Do not rest your weight on the device or place heavy  objects on it, and avoid use excessive force on the buttons, 
switches or connectors.
• Do not use the headphones for a long period of time at a  high or uncomfortable volume level, since this can cause 
permanent hearing loss. If you experience any hearing loss 
or ringing in the ears, consult a physician.
Always turn the power off when the device is not in use.
Even when the power is in standby status, electricity is 
still flowing to the device at the minimum level. When you 
are not using the device for a long time, make sure you 
unplug the power cord from the wall AC outlet.
Power supply/AC power adaptor
Location
Connections
Yamaha cannot be held responsible for damage 
caused by improper use or modifications to the 
device, or data that is lost or destroyed.
Maintenance
Handling caution
PA_en_1  2/2 
						

							6UR824 Getting Started
EnglishNOTICE
To avoid the possibility  of malfunction/ damage 
to the product, damage to data, or damage to 
other property, follow the notices below.
• Do not use the device in the vicinity of a TV, radio, stereo 
equipment, mobile phone, or other electric devices. 
Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibrations,  or extreme cold or heat (such as in direct sunlight, near a 
heater, or in a car during the day) to prevent the possibility 
of panel disfiguration, damage to the internal components 
or unstable operation.
• Do not place vinyl, plastic or rubber objects on the device,  since this might discolor the panel.
• When cleaning the device, use a soft, dry/dry or slightly  damp cloth. Do not use paint thinners, solvents, cleaning 
fluids, or chemical-impregnated wiping cloths.
• This disk containing the software is not meant for use with  an audio/visual system (CD player, DVD player, etc.). Do 
not attempt to use the disk on equipment other than a 
computer.
Information
• The software included in the Cubase AI DVD-ROM and the copyrights thereof are under exclusive ownership by 
Steinberg Media Technologies GmbH.
• The software included in the TOOLS for UR824 CD-ROM  and the copyrights thereof are under exclusive ownership 
by Yamaha.
• This manual is the exclusive copyrights of Yamaha  Corporation.
• Copying of the software or reproduction of this manual in  whole or in part by any means is expressly forbidden 
without the written consent of the manufacturer.
• Steinberg Media Technologies GmbH and Yamaha  Corporation make no representations or warranties with 
regard to the use of the software and documentation and 
cannot be held responsible for the results of the use of this 
manual and the software.
• The screen displays as illustrated in this manual are for  instructional purposes, and may appear somewhat 
different from the screens which appear on your computer.
• Copying of the commercially available musical data  including but not limited to MIDI data and/or audio data is 
strictly prohibited except for your personal use. • This product incorporates and bundles computer 
programs and contents in which Steinberg Media 
Technologies GmbH and Yamaha Corporation own 
copyrights or with respect to which it has license to use 
others' copyrights.  Such copyrighted materials include, 
without limitation, all computer software, style files, MIDI 
files, WAVE data, musical scores and sound recordings. 
Any unauthorized use of such programs and contents 
outside of personal use is not permitted under relevant 
laws.  Any violation of copyright has legal consequences.  
DON'T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
• Windows is a registered trademark of Microsoft
® 
Corporation in the United States and other countries.
• Apple, Mac and Macintosh are trademarks of Apple Inc.,  registered in the U.S. and other countries.
• Steinberg and Cubase are registered trademarks of  Steinberg Media Technologies GmbH.
• The company names and product names in this manual are  the trademarks or registered trademarks of their respective 
companies.
• Software may be revised and updated without prior notice. 
						

							UR824 Getting Started7
Introduction
English
Introduction
A Message From the 
Development Team
Thank you for choosing the UR824 USB Audio 
Interface. The UR824 brings the sum total of our 
experience and know-how together with 
invaluable feedback from our customers 
throughout the world. Throughout the Yamaha n-
series and Steinberg MR series our focus has 
been on integrating consistently outstanding 
sonic design with features and software that are 
truly useful from a musician’s perspective. The 
UR824 carries on this uncompromising 
approach, offering refined sound and 
functionality in a 1U rack mount unit.
With the goal of creating  a product that would be 
of maximum value for the longest time in mind, 
the development process began with in-depth 
review of the many comments received from 
users as a starting point  for the design and basic 
specifications. Visual desi gn, the feel of buttons 
and knobs, trial-and-error sonic evaluation of 
parts, and seamless software integration are just 
some of the elements to which every member of 
the development team devote d their full attention 
and passion. The entire team is rightly proud of 
the results, and we are delighted to be able to 
offer this product to our valued customers.
But this is just the beginning. The most important 
chapter unfolds when our customers use the 
product to support and au gment their creativity, 
making it a part of their musical lives. Our 
greatest hope is that we are able to contribute in 
some way to the creation and expression of new 
music that will bring our cu stomers’ artistic vision 
to life.
The Steinberg Hardware Development Team
Included Accessories
Accessories
•AC power adaptor 
(PA-300C or equivalent)
•Power cable
•Getting Started (this book)
•ESSENTIAL PRODUCT LICENSE 
INFORMATION card
•TOOLS for UR824 CD-ROM
•Cubase AI DVD-ROM
•USB cable
•Ferrite core
•Rubber stoppers x 4
NOTICE
If the ESSENTIAL  PRODUCT LICENSE 
INFORMATION card is lost or stolen, 
Steinberg Media Technologies GmbH 
and Yamaha Corporation cannot 
reissue it.
NOTE
•To prevent electromagnetic 
interference, fasten the ferrite core to 
the USB cable near the USB terminal on 
the computer.
•When using the unit on a slippery 
surface, attach the rubber stoppers to 
the specified location on the bottom 
panel of this device to prevent sliding.
Ferrite core
USB terminal on the Computer USB cable 
						

							Introduction
8UR824 Getting Started
EnglishDisk Contents
TOOLS for UR824 CD-ROM
•Operation Manual
This is the Operation Manual in PDF 
file format. For details, refer to the 
section “How to Read the Manual” 
(page 9).
•TOOLS for UR824
TOOLS for UR824 is necessary when 
connecting the device to a computer. 
When you install the TOOLS for 
UR824, the following two software 
programs will be installed. For 
instructions on installation, refer to the 
section “Setup” (page 12). 
- Yamaha Steinberg USB Driver This software allows 
communication between the device 
and a computer.
- Steinberg UR824 Applications This software allows setting the 
parameters of the device from a 
computer or using the Link function 
between the device and Cubase 
series. The software consists of the 
following four software 
components.
•dspMixFx UR824
This software lets you set the 
device when using it with a DAW 
(Digital Audio Workstation) 
software other than Cubase 
series.
•UR824 Extension
This software allows you to link the 
device with Cubase series (for 
versions which supports the link 
function). To use this Link function, you will 
need to install Cubase series 
version 5.5 or higher.
•Sweet Spot Morphing Channel 
Strip (VST Plug-in version)
This processing effect is a multi-
effect that combines compressor 
and equalizer. This is the VST 
Plug-in version (VST3.0) of the 
DSP effect equipped with the 
device.
•REV-X (VST Plug-in version)
This processing effect is a digital 
reverb platform developed by 
Yamaha for professional audio 
devices. This is the VST Plug-in 
version (VST3.0) of the DSP effect 
equipped with the device.
Cubase AI DVD-ROM
Cubase AI
Cubase AI is an entry-level program 
modeled on the flagship Cubase DAW 
software made by Steinberg, and 
provides basic function for the music 
recording/production. For instructions 
on installation, refer to the section 
“Setup” (page 12).
NOTE
For the latest information on the software 
contained in the accessory disk, please 
see the Steinberg web site below. Future 
upgrades of appl
ication and system 
software and any changes in 
specifications are announced separately 
on the website.
http://www.steinberg.net 
						

							UR824 Getting Started9
Introduction
English
How to Read the 
Manual
Types and Contents
Getting Started (this book)
Read this manual when setting up the 
device. After finishing the setup as 
indicated in this manual, read the 
Operation Manual.
Operation Manual (PDF file)
This manual provides instructions on 
how to use the device and gives 
detailed information on specific 
functions. It is included in the TOOLS 
for UR824 CD-ROM.
NOTE
•For contents of the operation manual, 
refer to the section “Contents of the 
Operation Manual” (page 21).
•To view PDF files, you will need to install 
Adobe Reader on you computer. You 
can download the latest Adobe Reader 
at the following web site.
http://www.adobe.com
Conventions
Windows or Mac
When the procedures or explanations 
are specific to only one of the 
platforms, Windows or Mac, this is 
properly indicated in the manual. When 
the platforms do not appear, 
procedures or explanations are for 
both Windows and Mac.
Procedures
“  ” appears on some procedures in 
the manual. For example, the string 
[Devices] 
 [Device Setup]  [Control 
Panel] indicates that you should 
perform the procedures in the following 
order.
1.Click the [Devices] menu.
2.Select the [Device Setup] option.
3.Click the [Control Panel] button.
Keyboard Shortcuts
[Windows modifier key]/[Mac modifier 
key]+[key] shows the shortcut keys. 
For example, [Ctrl]/[command]+[Z] 
means “press [Ctrl] under Windows or 
[command] under Mac, then press 
[Z].”
Different Cubase Programs
The phrase “Cubase series” applies to 
all Cubase programs and versions 
(except Cubase LE). If the instructions 
are only for Cubase, “Cubase only” 
appears in the manual.
Screens
This manual predominantly uses 
screenshots of Windows. However, 
Mac screenshots are used when 
instructions of the function apply only 
to the Mac. 
						

							Panel Controls and Terminals
10UR824 Getting Started
EnglishPanel Controls and Terminals
Rear Panel
DC IN 16V
 Grounding screw
 USB2.0 (USB port)
 WCLK switch
 WCLK IN (OUT) / OUT (BNC 
connector)
 OPTICAL A/B IN/OUT (optical)
 LINE OUTPUT 1–8 (phone type, 
balanced/unbalanced)
 MIC/LINE INPUT 3–8 (XLR/phone 
type, balanced/unbalanced)