Steinberg Ur22 User Guide
Have a look at the manual Steinberg Ur22 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 523 Steinberg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
Description of the device
UR22 Operation Manual6
CAUTION
• Do not connect or disconnect a device while turning
on the [INPUT 2 HI-Z] swit ch. Doing so can damage
the connected device an d/or the unit itself.
• To protect your speaker system, leave the
monitor speakers turned off when turning the
[INPUT 2 HI-Z] switch on/ off. It’s also a good idea
to turn all output level controls down to their
minimum. Neglect of these precautions may
result in large noise bu rsts that may damage
your...](http://img.usermanuals.tech/thumb/86/79958/w64_ur22-user-guide-1498815422_d-5.png "Page 6
Description of the device
UR22 Operation Manual6
CAUTION
• Do not connect or disconnect a device while turning
on the [INPUT 2 HI-Z] swit ch. Doing so can damage
the connected device an d/or the unit itself.
• To protect your speaker system, leave the
monitor speakers turned off when turning the
[INPUT 2 HI-Z] switch on/ off. It’s also a good idea
to turn all output level controls down to their
minimum. Neglect of these precautions may
result in large noise bu rsts that may damage
your...")
![Page 7
Description of the device
UR22 Operation Manual7
Rear Panel
[USB2.0] port
For connection to a computer.
USB Port Precautions
Be sure to observe the following points when
connecting to the computer’s USB interface. Failing
to do so may result in the computer freezing or
shutting down, as well as corruption or even loss of
data. If the device or computer does freeze, restart
the application or computer.
NOTICE
• Be sure to wake the computer from sleep/ suspended/stand by mode before making a...](http://img.usermanuals.tech/thumb/86/79958/w64_ur22-user-guide-1498815422_d-6.png "Page 7
Description of the device
UR22 Operation Manual7
Rear Panel
[USB2.0] port
For connection to a computer.
USB Port Precautions
Be sure to observe the following points when
connecting to the computer’s USB interface. Failing
to do so may result in the computer freezing or
shutting down, as well as corruption or even loss of
data. If the device or computer does freeze, restart
the application or computer.
NOTICE
• Be sure to wake the computer from sleep/ suspended/stand by mode before making a...")
![Page 12
UR22 Operation Manual12
6. While singing into the microphone, adjust
the output signal level of the headphones by
the [PHONES] knob on the device.
7. C l i c k “
Ô” (Record) to start the recording.
8. After finishing the recording, click “
□”
(Stop) to stop it.
9. Click the Ruler to move the project cursor to the desired point for starting playback.
10. Click “>”(Play) to check the recorded sound. When listening to the sound over monitor
speakers, adjust the output signal level by the
[OUTPUT...](http://img.usermanuals.tech/thumb/86/79958/w64_ur22-user-guide-1498815422_d-11.png "Page 12
UR22 Operation Manual12
6. While singing into the microphone, adjust
the output signal level of the headphones by
the [PHONES] knob on the device.
7. C l i c k “
Ô” (Record) to start the recording.
8. After finishing the recording, click “
□”
(Stop) to stop it.
9. Click the Ruler to move the project cursor to the desired point for starting playback.
10. Click “>”(Play) to check the recorded sound. When listening to the sound over monitor
speakers, adjust the output signal level by the
[OUTPUT...")
UR22 Operation Manual11 Configuring Audio Driver Settings on the DAW Software Cubase series Programs 1. Make sure that all applications have been closed. 2. Connect the device directly to the computer by using the included USB cable. NOTE ・ (Windows only) Make sure to use the same USB port as the one used in the installation procedure when you connect the UR22 to the computer again. If you connect it to a different USB port, you will have to install the driver again. 3. Double-click the shortcut of Cubase series on the desktop to start Cubase. 4. When the “ASIO Driver Setup” window appears while the Cubase series program is launching, confirm that the device is selected, then click “OK.” The audio driver settings are now complete. Programs Other Than Cubase Series 1. Make sure that all applications have been closed. 2. Connect the device directly to the computer by using the included USB cable. NOTE ・ Make sure that only one device compatible with Yamaha Steinberg USB Driver is connected. ・ (Windows only) Make sure to use the same USB port as the one used in the installation procedure when you connect the UR22 to the computer again. If you connect it to a different USB port, you will have to install the driver again. 3. Launch the DAW software. 4. Open the audio interface settings windows. 5. (Windows only) Select the “ASIO Driver” for the audio driver settings. 6. Set as follows. Windows Set the Yamaha Steinberg USB ASIO for the ASIO Driver settings. Mac Set the UR22 for the audio interface settings. The audio driver settings are now complete. Recording/Playback Cubase Series Programs 1. Launch the Cubase series DAW. The “Project Assistant” window appears. 2. Select the desired project template in “Recording” on the “Project Assistant” window, then click “Create.” 3. When the “Missing Ports” window appears, select the UR22 port for each of the “Mapped Ports.” Enter checkmarks to the corresponding “Map Always” boxes, then click “OK.” NOTE ・ If you enter a checkmark for “Map Always,” the “Missing Ports” window will not appear from the next time. 4. Set the [MIX] knob to the center position between [INPUT] and [DAW]. 5. While singing into the microphone, adjust the input signal level of the microphone by the [INPUT GAIN] knob on the device. To achieve optimum recording levels, increase the input level with the [INPUT GAIN] knob until the [PEAK] indicator light s in red, then slowly bring the level down unti l it stops lighting in red.
UR22 Operation Manual12 6. While singing into the microphone, adjust the output signal level of the headphones by the [PHONES] knob on the device. 7. C l i c k “ Ô” (Record) to start the recording. 8. After finishing the recording, click “ □” (Stop) to stop it. 9. Click the Ruler to move the project cursor to the desired point for starting playback. 10. Click “>”(Play) to check the recorded sound. When listening to the sound over monitor speakers, adjust the output signal level by the [OUTPUT LEVEL] knob on the device. Operation is now complete. For instructions on using Cubase series programs, refer to the PDF manual, available from “Help” in the Cubase series menu. Programs Other Than Cubase Series 1. Launch your DAW software. 2. While singing into the microphone, adjust the input signal level of the microphone by the [INPUT GAIN] knob on the device. To achieve optimum recording levels, increase the input level with the [INPUT GAIN] knob until the [PEAK] indicator lights in red, then slowly bring the level down unt il it stops lighting in red. 3. While singing into the microphone, adjust the output signal level of the headphones by the [PHONES] knob on the device. 4. Start recording on your DAW software. 5. After finishing recording, stop it. 6. Play back the newly recorded sound to check it. Operation is now complete. For instructions on using the DAW software, refer to your particular DAW’s software manual.
Troubleshooting UR22 Operation Manual13 Troubleshooting Power does not turn on. ・Make sure that the device is properly connected to the computer via a USB cable. Connecting between the computer and the device via a USB cable supplies power source to the device. ・ Confirm whether or not a proper USB cable is used. If the USB cable is broken or damaged, replace the USB cable with a new one. Use a USB cable no longer than 3 meters. ・ Has Yamaha Steinberg USB Driver been installed properly? Refer to the Getting started to complete Yamaha Steinberg USB Driver installation. No Sound ・ Are the volume controls of the device set to appropriate levels? Confirm the levels of the [OUTPUT] knob and [PHONES] knob. ・ Are the microphones and monitor speakers connected to the device properly? Refer to the section “Connection Examples” (page 10) to confirm the connection. ・ Are the audio driver settings on DAW software set properly? Refer to the section “Configuring the Audio Driver Settings on DAW Software” (page 11) to set it. ・ Is the “ASIO Driver” setting on the Cubase series program set properly? From the Cubase series menu, open the “Devices” → “Device Setup…” → “VST Audio System”, then confirm that the “Yamaha Steinberg USB ASIO” (Windows) or “Steinberg UR22” (Mac) is selected on the“ASIO Driver.” ・ Was the power of the device turned on before starting the DAW software? Before starting the DAW software, connect the device to a computer and turn on the power of the device. ・ Is the device connected to a computer via a USB hub? Connect it directly without using a USB hub. ・ Has Yamaha Steinberg USB Driver been installed properly? Refer to the Getting started to complete Yamaha Steinberg USB Driver installation. ・ Are any USB devices you are not using connected to the computer? Remove them then confirm the sound. ・ Are any other applications running at the same time? Quit all applications you are not using then confirm the sound. ・ Is the UR22 selected in the control panel for Yamaha Steinberg USB Driver? (Windows only) When connecting two or more devices compatible with the Yamaha Steinberg USB Driver to the computer, select UR22 in the Device settings (page
Troubleshooting UR22 Operation Manual14 8) of the Yamaha Steinberg USB Driver control panel. Unusual Sound (noise, interruption, or distortion) ・Is the buffer size set too low? Increase the buffer size compared to the current settings; refer to the section “Yamaha Steinberg USB Driver”(page 8) for instructions. ・Does your computer satisfy the system requirements? Confirm the system requirements. For the latest information, see the Steinberg web site below. http://www.steinberg.net/ ・ Are you recording or playing long continuous sections of audio? The audio data processi ng capabilities of your computer will depend on a number of factors including CPU speed and access to external devices. Reduce the audio tracks then confirm the sound. ・ Is a network adaptor for wired/ wireless LAN running? Disable the suspected network adaptor. Some network adaptors can cause noise. Double Sound ・ Both the input signal to the device and the output signal from DAW software are being output. Turn the [MIX] knob fully to the [DAW] side. Computer does not recognize the device. (USB indicator does not switch from flashing to being continuously lit.) ・ Has Yamaha Steinberg USB Driver been installed properly? Refer to the Getting started to complete Yamaha Steinberg USB Driver installation.
Appendix UR22 Operation Manual15 Appendix Uninstalling Yamaha Steinberg USB Driver Windows 1. Disconnect all USB devices other than the mouse and keyboard from the computer. 2. Start the computer and log on to the Administrator account. Exit any open applications and close all open windows. 3. Open the window for the uninstall operation as follows. Select “Control Panel” → “Uninstall a Program” to call up the “Uninstall or change a program” panel. 4. Select “Yamaha Steinberg USB Driver” from the list. 5. Uninstall them as follows. Click the “Uninstall” / “Uninstall / Change”. If the “User Account Control” window appears, click “Continue” or “Yes.” Follow the on-screen instructions to remove the software. Uninstallation of Yamaha Steinberg USB Driver is now complete. Mac 1. Disconnect all USB devices other than the mouse and keyboard from the computer. 2. Start the computer and log in to the Administrator account. Exit any open applications and close all open windows. 3. Insert the TOOLS for UR22 CD-ROM into the CD-ROM drive. 4. Open the CD-ROM then double-click the file “Uninstall Yamaha Steinberg USB Driver.” 5. Click “Run” when the “Welcome to the Yamaha Steinberg USB Driver uninstaller.” message appears. After that, follow the onscreen instructions to uninstall the software. 6. After completing the uninstallation, an “Uninstallation completed.” window appears. Click “Restart.” 7. When the message prompting you to restart your computer appears, click “Restart.” Uninstallation of Yamaha Steinberg USB Driver is now complete.
Appendix UR22 Operation Manual16 Block Diagrams :Ÿ:˜ :¤: :š:†:£: :¥:œ:w: :¥:§:¬:« :ž:˜: :¥ :¬:ª:™ :œ:¥:š:¦:©:›:œ:© :›:œ:š:¦:©:›:œ:© :›:˜:®:w: :¥:§:¬:«:†:¦:¬:«:§:¬:«:‰:w: :¥:§:¬:«:†:w:‰:w:¦:¬:«:§:¬:« :Ÿ:˜:ž:˜: :¥ :Ÿ:À:„:± :¦:¥ :£: :¥:œ:w:¦:¬:«:§:¬:« :ˆ:†:£ :£:œ::œ:£:£:œ::œ:£ :‰:†:© :²:‚:‹:»:™:Ì:´ :§:Ÿ:¦:¥:œ:ª :«:¦:w:›:˜:®:w:ˆ :«:¦:w:›:˜:®:w:‰ :¤: :¯ :«:¦:w:›:˜:®:w:ˆ:†:‰ :§:œ:˜:¢ :§:œ:˜:¢ : :¥:§:¬:« :›:˜:® : :¥:§:¬:« :›:˜:® :˜:†:›:˜:†:› :›:†:˜:›:†:˜ :²:„:Œ:‹:»:™:ÌC>:„:ˆ:‡:»:™:Ì:´ :¤: :š :²:„:Š:‡:»:™:ÌC>:‚:ˆ:‹:»:™:Ì:´ :£: :¥:œ :²:„:Œ:‹:»:™:ÌC>:„:ˆ:‡:»:™:Ì:´ :¤: :š :²:„:Š:‡:»:™:ÌC>:‚:ˆ:‹:»:™:Ì:´ :£: :¥:œ :Ÿ: :„:± :
Appendix UR22 Operation Manual17 Specifications Technical Specifications MIC INPUT 1/2 (Balanced) Maximum Input Level ±0 dBu Input Impedance 4 kΩ GAIN Range +10 dB to +54 dB LINE INPUT 1/2 (Balanced) Maximum Input Level +24 dBu Input Impedance20 kΩ GAIN Range -14 dB to +30 dB HI-Z INPUT 2 (Unbalanced) Maximum Input Level +5.8 dBV Input Impedance1 MΩ GAIN Range +0.8 dB to +44.8 dB LINE OUTPUT 1/L 2/R (Impedance balanced) Maximum Output Level +10dBu Output Impedance150 Ω PHONES Maximum Output Level 6 mW+6 mW, 40 Ω USB Specification USB2.0, 24 bit, 44.1 kHz/48 kHz/88.2 kHz/96 kHz/176.4 kHz/192 kHz XLR INPUT Polarity Pin 1: Ground Pin 2: Hot (+) Pin 3: Cold (-)
Appendix UR22 Operation Manual18 General Specifications Specifications and descriptions in this manual are for information purposes only. Steinberg/Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Steinberg/ Yamaha dealer.Dimensions (WxHxD) 158.6 x 47 x 158.3 mm Net Weight 998 g Operating Free-air Temperature Range 0 to 40 °C Included Accessories • Getting started (printed) • CUBASE AI DOWNLOAD INFORMATION (printed) • TOOLS for UR22 CD-ROM • USB Cable
Steinberg Web Site http://www.steinberg.net/ C.S.G., PA Development Division © 2012-2014 Yamaha Corporation 402MW-B0