Steinberg Nuendo 4 Remote Control Devices Manual

11
Remote controlling Nuendo
CM Automation Motor Mix
Specifications
The CM Motor Mix can control any number of channels in 
groups of 8.
Press the “” buttons (at the top of the View 
section) to select channels 1–8, 9–16 etc. Hold down 
Shift and press “” to shift the fader assignment in 
steps of one channel.
Press F1 to disable/enable the fader motors.
Use the Select buttons (the row of buttons next to the 
display) to select a single track for detailed settings.
The Mute and Solo buttons are used to...

12
Remote controlling Nuendo
Selected Channel mode Panning:
 Page 1 – panning left/right, panning front/rear
 Buttons below dials: monitor
Selected Channel mode Routing:
 Page 1 – Output Bus, Monitor, Input Bus, Input Gain, Input 
Phase
 Buttons below dials: monitor
Fader Set mode EQ1 to EQ4 (e. g. EQ1):
 Page 01 – EQ Low Gain
 Page 02 – EQ Low Frequency 
 Page 03 – EQ Low Q
 Page 04 – EQ Low Enable

 Buttons below dials: bypass EQs
Fader Set mode Send1 to Send8 (e. g. Send1):
 Page 01 – Send1 Level...

13
Remote controlling Nuendo
Fader Set Section:
 [Shift]+[FX Send1]: Studio Send 1
 [Shift]+[FX Send2]: Studio Send 2
 [Shift]+[FX Send3]: Studio Send 3
 [Shift]+[FX Send4]: Studio Send 4
 Page 1 – Level
 Page 2 – Enable

 Page 4 – Pan Left/Right
JL Cooper CS-10
Specifications
The CS-10 can remote control 32 channels (in groups of 
8). The following CS-10 controls will remote control the 
following parameters for each channel strip:

 Solo and Mute: solo and mute
 Sel: select channel for editing
The...

14
Remote controlling Nuendo
You can create markers by pressing the “Set Locate” 
key on the MCS-3000, typing in a marker ID and pressing 
[Return].
To locate to a marker, press “Locate”, type in a marker 
ID and press [Return].
The MCS-3000 Play, Stop, Record, Rewind and Fast 
Forward transport controls will have the equivalent func-
tionality in Nuendo.
Mackie Control
Mackie Control is an automated touch-sensitive control 
surface. It is a nine-fader (eight channels and master) MIDI 
controller that...

15
Remote controlling Nuendo
The Touch, Latch and Trim buttons in the Auto Mode 
section are currently not supported.
Use the Transport button in the Window section to 
open or close the Transport panel.
Use the Edit button in the Window section to bring the 
current Project window to the front.
Use the Status button in the Window section to open or 
close the VST Performance window.
Use the Mix button in the Window section to open or 
close the Mixer window.
Use the Mem-Loc button in the Window section...

16
Remote controlling Nuendo
F2 button: Selected Channel: Sends
 Pages 1 to 8 – Level, Enable, Pre/Post and Bus for Sends 1 
to 8
 Buttons above dials: bypass sends
F3 button: Selected Channel: Routing
 Page 1 – Output Bus, Monitor, Input Bus, Input Gain
 Page 2 – Input Phase
 Buttons above dials: monitor
For a description of the functionalities for the F4 button: 
Selected Channel: Inserts, F5 button: Global mode Send 
Effects, F6 button: Global mode Master Effects, F7 but-
ton: Global mode Instruments,...

17
Remote controlling Nuendo
The status of the Num button (in the Software Naviga-
tion section) determines the assignment of the “1” to “0” 
and Enter buttons:
With Num-LED on, use the buttons to set the project cur-
sor position:
 Immediately after you enter a numeric character, the SAC-2k 
time display will no longer show the project cursor position 
but the new value.
 You don’t have to enter decimal points, colons, or semicolons 
for a new value.
 Num button: delete the new value and deactivate...

18
Remote controlling Nuendo
For a description of the functionalities for the MIDI button: 
Selected Channel mode Inserts, Shift+Inserts/Sends but-
ton: Global mode Send Effects, Shift+Dynamics button: 
Global mode Master Effects, Shift+MIDI button: Global 
mode Instruments, see the separate pdf document 
“Mackie Control and Nuendo”.
In this version of Nuendo, the following functions have 
been added:
Instrument button: Selected channel mode Instrument:
 Page 1 – Select instrument
 Page 2-n – Instrument...

19
Remote controlling Nuendo
EQ-Freq
Controls the EQ frequency for each band selected with the Low, LoMid, 
HiMid and High buttons. These correspond to the four EQ bands in Nu-
endo, starting from the leftmost band.
EQ-“Q”
Controls the EQ “Q” for each band selected with the Low, LoMid, HiMid 
and High buttons. These correspond to the four EQ bands in Nuendo, 
starting from the leftmost band.
Aux 1 to Aux 4 and shuttle wheel: 
The effect send levels for sends 1 to 4. 
The shuttle wheel will act as...

20
Remote controlling Nuendo
Fader level, mute and pan.
01V controls for these parameters control the equivalent Nuendo param-
eters.
Effect sends 1–6.
01V Aux 1–4 control effect send 1–4, 01V effect 1 and 2 control effect 
send 5 and 6.
EQ Frequency, Gain and Q (4 bands).
01V controls for these parameters control the equivalent Nuendo param-
eters.
Stereo Master Volume.
The 01V control for this parameter controls the equivalent Nuendo pa-
rameter.
Send effects master volume 1–4 are controlled by 01V...