Steinberg Cubase SE 3 Audio Effects And VSTi Manual

							 
Audio Effects and VST Instruments  
						

							 
Original Manual: Synkron
Revision and Quality Control: C. Bachmann, H. Bischoff, S. Pfeifer, C. Schomburg
The information in this document is subject to change without notice and does not rep-
resent a commitment on the part of Steinberg Media Technologies GmbH. The software 
described by this document is subject to a License Agreement and may not be copied 
to other media except as specifically allowed in the License Agreement. No part of this 
publication may be copied, reproduced or otherwise transmitted or recorded, for any 
purpose, without prior written permission by Steinberg Media Technologies GmbH.
All product and company names are ™ or ® trademarks of their respective owners. 
Windows XP is a trademark of Microsoft Corporation. The Mac logo is a trademark 
used under license. Macintosh and Power Macintosh are registered trademarks.
© Steinberg Media Technologies GmbH, 2005. 
All rights reserved. 
						

							 
Table of Contents 
						

							 
CUBASE SE
 4 Table of Contents 
5The included effect plug-ins 
6Introduction
7Delay plug-ins
10Distortion plug-ins
13Dynamics plug-ins
21Filter plug-ins
24Modulation plug-ins
36Other plug-ins
43Restoration
44Reverb plug-ins 
47The included VST Instruments 
48VB-1 Bass Synth
50LM-7 Drum Machine
53Universal Sound Module (USM) 
57Index 
						

							 
1
 
The included effect plug-ins 
						

							 
CUBASE SE
1 – 6 The included effect plug-ins 
Introduction
 
This chapter contains descriptions of the included plug-in effects and 
their parameters.
In Cubase SE, the plug-in effects are arranged in a number of different 
categories. This chapter is arranged in the same fashion, with the plug-
ins listed in separate sections for each effect category. 
						

							 
CUBASE SE
The included effect plug-ins 1 – 7 
Delay plug-ins
 
This section contains descriptions of the plug-ins in the “Delay” 
category. 
DoubleDelay
 
This effect provides two separate delays that can be either tempo 
based or use freely specified delay time settings. Cubase SE automat-
ically provides the plug-in with the tempo currently used in the project. 
The parameters are as follows: 
Parameter Description  
Mix Sets the level balance between the dry signal and the effect. If Double-
Delay is used as a send effect, this should be set to maximum (100%) 
as you can control the dry/effect balance with the send. 
Tempo sync 
on/offThe buttons above the two Delay Time knobs are used to turn tempo 
sync on or off for the respective delay. If set to off the delay time can be 
set freely with the Delay Time knobs, without sync to tempo.
Delay Time 1 This is where you specify the base note value for the delay if tempo 
sync is on (1/1 - 1/32, straight, triplet or dotted). If tempo sync is off, it 
sets the delay time in milliseconds.
Delay Time 2 As above.
Feedback This sets the number of repeats for both delays.
Tempo Sync 1 The note value multiplier (x1 to x10) for the first delay unit. 
Tempo Sync 2 As above, but for the second delay unit.  
						

							 
CUBASE SE
1 – 8 The included effect plug-ins 
You can also change parameters in the graphic display window. This 
works as follows:  
•  
If tempo sync is on, you can set the Tempo Sync 1 parameter by drag-
ging the light blue handle left and right. 
When tempo sync is off, this sets the Delay Time 1 parameter.
 
•  
You can set the Pan 1 parameter by dragging the light blue handle up 
and down.  
•  
The dark blue handle works in the same way but for the correspond-
ing second delay parameters. 
Pan1 This sets the stereo position for the first delay.
Pan2 This sets the stereo position for the second delay.  
Parameter Description 
						

							 
CUBASE SE
The included effect plug-ins 1 – 9 
ModDelay
 
This is a delay effect that can either be tempo-based or use freely spec-
ified delay time settings. The delay repeats can also be modulated.
The parameters are as follows: 
Parameter Description  
Mix Sets the level balance between the dry signal and the effect. If ModDelay 
is used as a send effect, this should be set to maximum as you can con-
trol the dry/effect balance with the send. 
Tempo sync 
on/offThe button above the Delay Time knob is used to turn tempo sync on or 
off. If set to off the delay time can be set freely with the Delay Time knob, 
without sync to tempo.
Feedback This sets the number of repeats for the delay.
Delay Time This is where you specify the base note value for the delay if tempo sync 
is on (1/1 - 1/32, straight, triplet or dotted). If tempo sync is off, it sets 
the delay time in milliseconds.
Tempo Sync 
knobThis is the note value multiplier (x1 to x10) for the delay when tempo sync 
is used. 
DelayMod. This controls the pitch modulation rate for the delay effect.   
						

							 
CUBASE SE
1 – 10 The included effect plug-ins 
Distortion plug-ins
 
This section contains descriptions of the plug-ins in the “Distortion” 
category. 
DaTube
 
This effect emulates the characteristic warm, lush sound of a tube 
amplifier.
The parameters are as follows: 
Parameter Description  
Drive Regulates the pre-gain of the “amplifier”. Use high values if you want an 
overdriven sound just on the verge of distortion.
Balance This controls the balance between the signal processed by the Drive pa-
rameter and the dry input signal. For maximum drive effect, set this to its 
highest value.
Output Adjusts the post-gain, or output level, of the “amplifier”.