Steinberg Cubase 4 Remote Control Devices Manual

							11
Remote controlling Cubase
In the View section, select Write or “fnct B” to control 
the Write or Read buttons in the Cubase mixer. When 
Write/fnct B is selected, selecting the All button in the 
bottom left section of the CM Motor Mix controls the Write 
All/Read All buttons in the Cubase mixer.
The Auto Enbl button controls Start/Stop in Cubase.
The Suspend button controls the Record function in 
Cubase.
Press the DSP button to move the project cursor to the 
start of the project.
Hold down Shift and press the DSP button to move the project cursor to 
the end of the project.
Press the Window button to move the project cursor to 
the left locator.
Hold down Shift and press the Window button to move the project cur-
sor to the right locator.
Press the Default button to switch automatic punch in 
on or off.
Hold down Shift and press the Default button to switch automatic punch 
out on or off.
Press the Undo button to undo the last action in Cu-
base.
Hold down Shift and press the Undo button to “undo the undo”.
In the Rotary section, use the Rotary dial to change the as-
signment of the four buttons below the dial (indicated in 
the ROTARY display):
ROTARY: PA
 equaliz button: Fader Set mode Panning
 dynmics button: Fader Set mode Routing
 delay button: Selected Channel mode Panning
 special button: Selected Channel mode Routing 
ROTARY: EQ
 equaliz button: Fader Set mode EQ Low (EQ1)
 dynmics button: Fader Set mode EQ Mid-Low (EQ2)
 delay button: Fader Set mode EQ Mid-High (EQ3)
 special button: Fader Set mode EQ High (EQ4)
ROTARY: S1
 equaliz button: Fader Set mode Send 1
 dynmics button: Fader Set mode Send 2
 delay button: Fader Set mode Send 3
 special button: Fader Set mode Send 4
ROTARY: S2
 equaliz button: Fader Set mode Send 5
 dynmics button: Fader Set mode Send 6
 delay button: Fader Set mode Send 7
 special button: Fader Set mode Send 8
Use the Bank Up button in the View section for page up.
Hold down Shift and press the Bank Up button to jump to the last page.
Use the Bank Down button in the View section for page 
down.
Hold down Shift and press the Bank Down button to jump to the first page.
Press the Rotary dial to switch the display of names of 
the available parameters or the page name on or off.
Fader Set mode Panning:
 Page 1 – panning left/right
 Page 2 – panning front/rear
 Buttons below dials: monitor
Fader Set mode Routing:
 Page 1 – Output Bus




 Buttons below dials: monitor
Selected Channel mode Panning:
 Page 1 – panning left/right, panning front/rear
 Buttons below dials: monitor
Selected Channel mode Routing:
 Page 1 – Output Bus, Monitor, Input Bus, Input Gain, Input 
Phase
 Buttons below dials: monitor 
						

							12
Remote controlling Cubase
Fader Set mode EQ1 to EQ4 (e. g. EQ1):
 Page 01 – EQ Low Gain
 Page 02 – EQ Low Frequency 
 Page 03 – EQ Low Q
 Page 04 – EQ Low Enable

 Buttons below dials: bypass EQs
Fader Set mode Send1 to Send8 (e. g. Send1):
 Page 01 – Send1 Level
 Page 02 – Send1 Enable
 Page 03 – Send1 Pre/Post
 Page 04 – Send1 Bus
 Page 05 – Bypass Sends
 Buttons below dials: bypass sends
F2 button: Selected Channel mode EQ:
 Page 1 – Gain, Frequency, Q and Enable for the lo band, 
Gain, Frequency, Q and Enable for the lo mid band
 Page 2 – Gain, Frequency, Q and Enable for the hi mid band, 
Gain, Frequency, Q and Enable for the hi band
 Buttons below dials: bypass EQs
Holding down Shift and pressing the F2 button gives you 
a variation of Selected Channel mode EQ:
 Page 1 – Gain and Frequency for all bands
 Page 2 – Q and Enable for all bands
 Buttons below dials: bypass EQs
F3 button: Selected Channel mode Sends
 Page 1 – Level, Enable, Pre/Post and Bus for Send 1 and 
Send 2
 Page 2 – Level, Enable, Pre/Post and Bus for Send 3 and 
Send 4
 Page 3 – Level, Enable, Pre/Post and Bus for Send 5 and 
Send 6
 Page 4 – Level, Enable, Pre/Post and Bus for Send 7 and 
Send 8
 Buttons below dials: bypass sends
Holding down Shift and pressing the F3 button gives you 
a variation of Selected Channel mode Sends:
 Page 1 – Level for Send 1 to Send 8
 Page 2 – Enable for Send 1 to Send 8
 Page 3 – Pre/Post for Send 1 to Send 8
 Page 4 – Bus for Send 1 to Send 8
 Buttons below dials: bypass sends
For a description of the functionalities for the F4 button: 
Selected Channel mode Inserts, Next button: Global 
mode Send Effects, Last button: Global mode Master Ef-
fects, and Enter button: Global mode Instruments, see the 
separate pdf document “Mackie Control and Cubase”.
Steinberg Houston
Houston is a MIDI/USB remote control device designed 
especially for use with VST audio applications such as 
Cubase. With clearly laid out controls (including touch 
sensitive motorized faders, rotary knobs, transport con-
trols and a jog/shuttle wheel) Houston allows you to con-
trol virtually Cubase, without having to use the computer 
keyboard or mouse.
For details about parameters and hands-on mixing tech-
niques, please see the Houston documentation.
In this version of Cubase, the following functions have 
been added:
[Dyn/User1]: Studio Send for selected channel


 Page 03 – Pre/Post
 Page 04 – Pan Left/Right
[User2]: Instrument for selected channel (Instrument 
tracks and MIDI track to VSTi from the Rack)
 Page 1 – Select instrument
 Page 2-n – Instrument parameter
Fader Set Section:
 [Shift]+[FX Send1]: Studio Send 1
 [Shift]+[FX Send2]: Studio Send 2
 [Shift]+[FX Send3]: Studio Send 3
 [Shift]+[FX Send4]: Studio Send 4
 Page 1 – Level
 Page 2 – Enable
 Page 3 – Pre/Post
 Page 4 – Pan Left/Right 
						

							13
Remote controlling Cubase
JL Cooper CS-10
The CS-10 can remote control 32 channels (in groups of 
8). The following CS-10 controls will remote control the 
following parameters for each channel strip:

 Solo and Mute: solo and mute
 Sel: select channel for editing
The following parameters can be remote controlled for each 
selected channel using the six rotary knobs on the CS-10:
The CS-10 function keys 1–4 are used to select chan-
nels 1–32 in groups of 8. 
Function key 1 selects channels 1–8, function key 2 selects channels 9–
16, and so on.
If you hold down the function key “Shift” and then move 
a fader, the two indicators beside the fader will indicate 
whether the fader position is below or above the current 
fader level in Cubase. 
If the upper indicator is lit, the fader position on the panel is above the 
fader level in Cubase and vice versa. When both indicators are dark, the 
fader positions are matched for that channel.
The CS-10 Play, Stop, Record, Rewind and Fast For-
ward transport controls control the equivalent functions in 
Cubase.
JL Cooper MCS-3000
The MCS-3000 can control 32 mixer channels remotely 
(in groups of 8). The following MCS-3000 controls will re-
mote control the following mixer parameter for each chan-
nel strip:
Fader: volume
Solo and Mute: solo and mute
Sel: Select channel for editing
These parameters can be remote controlled for each selected channel 
using the dials on the MCS-3000 and switching between Pages 1–4: 
The MCS-3000 bank keys 1–4 are used to select 
channels 1–32 in groups of 8. 
Bank key 1 selects channels 1–8, bank key 2 selects channels 9–16, etc.
You can create markers by pressing the “Set Locate” 
key on the MCS-3000, typing in a marker ID and pressing 
[Return].
To locate to a marker, press “Locate”, type in a marker 
ID and press [Return].
Dial Parameter
Send 1 Effect send 1
Send 2 Effect send 2
Pan Pan
Boost/cut EQ 1 Gain
Frequency EQ 1 Frequency
Bandwidth EQ 1 Q Factor
!The CS-10 supports “MIDI Feedback”, allowing the 
mute, solo and selection status of channels in Cubase 
to be indicated on the panel. For this (and the fader 
position indication described above) to work, you 
need a two-way MIDI connection between the CS-10 
and Cubase.
Page 1 Page 2
Dial Parameter Dial Parameter
1Pan1EQ 1 Gain
2 Effect send 1 2 EQ 1 Freq
3 Effect send 2 3 EQ 1 “Q”
4 Effect send 3 4 EQ 1 Low Limit
5 Effect send 4 5 EQ 1 High Limit
Page 3 Page 4
Dial Parameter Dial Parameter
1 EQ 2 Gain 1 EQ 3 Gain
2 EQ 2 Freq 2 EQ 3 Freq
3 EQ 2 “Q” 3 EQ 3 “Q”
4 EQ 2 Low Limit 4 EQ 3 Low Limit
5 EQ 2 High Limit 5 EQ 3 High Limit 
						

							14
Remote controlling Cubase
The MCS-3000 Play, Stop, Record, Rewind and Fast 
Forward transport controls will have the equivalent func-
tionality in Cubase.
Mackie Control
Mackie Control is an automated touch-sensitive control 
surface. It is a nine-fader (eight channels and master) MIDI 
controller that provides in-depth mixing, editing, automa-
tion and navigational control for any supported digital au-
dio workstation.
A special Lexan overlay that shows all Steinberg-specific 
key assignments for the Mackie Control device is available 
to customize the controller for Cubase.
For details about parameters and hands-on mixing tech-
niques, please see the separate pdf documentation de-
scribing the use of Mackie Control with Cubase.
Mackie HUI
Mackie HUI can control any number of channels in groups 
of 8.
Use the left and right Bank buttons to select channels 
1–8, 9–16 etc.
Use the left and right Channel buttons to shift the fader 
assignment in steps of one channel.
The Fader button in the Auto Enable section is used to 
disable/enable the motors.
The Mute, Pan, Send, Plug In and Send Mute buttons in 
the Auto Enable section are currently not supported.
Use the Rec/Rdy buttons to arm a track for recording.
Use the Select buttons to select a single track for de-
tailed settings.
With the Mute and Solo buttons you can mute or solo a 
track.
Use the Default button to un-solo all tracks.
Use the Assign button to un-mute all tracks.To the right of the time display, you find an LED labeled 
“Rude Solo Light”. This LED lights up as soon as any 
channel is soloed.
Use the Insert buttons to bypass all inserts of one track.
Pan button in the Select Assign section:
 Fader Set: panning left/right or panning front/rear. Press but-
ton repeatedly to cycle through the assignments (the eight V-
Pots control the pan parameters).
 V-Sel button in the Select Assign section: monitor track.
Send A to Send E buttons in the Select Assign section:
 Fader Set: Send 1 level to Send 8 level (Send A to Send D 
assigns Send 1 to Send 4, Send E assigns Send 5 to Send 8: 
press button repeatedly to cycle through the assignments).
 V-Sel button in the Select Assign section: send on/off switch 
(depending on selected Send).
 V-Sel button with Shift in the Select Assign section selected: 
pre/post fader switch (depending on selected Send).
The SELECT ASSIGN four character display in the Se-
lect Assign section displays Send or Pan assignment for 
V-Pots and V-Sel buttons.
The four character displays above the Select buttons 
display the assigned track names.
The Bypass button in the Select Assign section is al-
ways selected to indicate the bypass function of the Insert 
buttons.
The Mute, Rec/Rdy All, Input and Output buttons in the 
Select Assign section are currently not supported.
Use the Auto buttons to control the status of the Read 
and Write buttons in the Mixer of Cubase, depending on 
the Read/Write status in the Auto Mode section.
Use the Off button in the Auto Mode section to control 
the Read All or Write All button in the mixer of Cubase, 
depending on the Read/Write status in the Auto Mode 
section.
The Touch, Latch and Trim buttons in the Auto Mode 
section are currently not supported.
Use the Transport button in the Window section to 
open or close the Transport panel.
Use the Edit button in the Window section to bring the 
current Project window to the front.
!The MCS-3000 supports “MIDI Feedback”, allowing 
fader settings and channel mute, solo and selection 
status to be indicated on the panel. For this to work, 
you need a two-way MIDI connection between the 
MCS-3000 and Cubase. 
						

							15
Remote controlling Cubase
Use the Status button in the Window section to open or 
close the VST Performance window.
Use the Mix button in the Window section to open or 
close the Mixer window.
Use the Mem-Loc button in the Window section to 
open the Marker window.
The Alt button in the Window section is used for user-
assigned functions.
The Undo button in the Keyboard Shortcuts section un-
does the last performed operation in Cubase.
Hold down the Shift button and press Undo to redo the last undone op-
eration.
Press the Save button in the Keyboard Shortcuts sec-
tion to save the current project.
Hold down the Shift button and press the Save button to save a backup 
copy of the current project.
The Edit Mode, Edit Tool, Option/All, Ctrl/Clutch and 
Alt/Fine buttons in the Keyboard Shortcuts section are 
currently not supported.
The Cut, Copy, Paste and Delete buttons in the Edit 
section control the equivalent Cubase functions.
The Capture and Separate buttons in the Edit section 
are currently not supported.
The buttons in the Status/Group section are currently 
not supported.
Use the In and Out buttons above the transport controls 
to set the project cursor to the positions of the left or right 
locators.
Hold down the Shift button and press the In or Out button to move the 
left or right locator to the current project cursor position.
Use the RTZ and END buttons to set the project cursor 
to the beginning or the end of the project.
Press the Quick Punch button to switch automatic 
punch in on or off.
Hold down the Shift button and press the Quick Punch button to switch 
automatic punch out on or off.
Press the Loop button to switch Cycle mode on or off.
Press the On Line button to switch Synchronization on 
or off.
The Audition, Pre and Post buttons are used for user 
assignable functions (see function keys F1 to F7).The Mackie HUI Play, Stop, Record, Rewind and Fast 
Forward transport controls control the equivalent func-
tions in Cubase.
The jog wheel is used for moving the project cursor po-
sition in Cubase.
The Scrub and Shuttle buttons are currently not sup-
ported.
Pressing the cursor keys located to the left of the jog 
wheel is the same as pressing the arrow keys on your 
computer keyboard.
When the Mode button is selected, pressing the cursor keys will control 
zooming in the Project window.
Use the Scroll control in the DSP Edit/Assign section to 
scroll through the pages of one parameter group.
Use the Compare button in the DSP Edit/Assign sec-
tion for page up.
Hold down the Shift button in the Keyboard Shortcuts section and press 
the Compare button to jump to the last page.
Use the Bypass button in the DSP Edit/Assign section 
for page down.
Hold down the Shift button in the Keyboard Shortcuts section and press 
the Bypass button to jump to the first page.
Use the Insert/Param button in the DSP Edit/Assign 
section to switch the display of names of the available 
parameters in the lower row on or off.
F1 button: Selected Channel: EQ
 Page 1 – Gain, Frequency, Q and Enable for the lo band
 Page 2 – Gain, Frequency, Q and Enable for the lo mid band
 Page 3 – Gain, Frequency, Q and Enable for the hi mid band
 Page 4 – Gain, Frequency, Q and Enable for the hi band
 Buttons above dials: bypass EQs
F2 button: Selected Channel: Sends
 Pages 1 to 8 – Level, Enable, Pre/Post and Bus for Sends 1 
to 8
 Buttons above dials: bypass sends
F3 button: Selected Channel: Routing
 Page 1 – Output Bus, Monitor, Input Bus, Input Gain

 Buttons above dials: monitor 
						

							16
Remote controlling Cubase
For a description of the functionalities for the F4 button: 
Selected Channel: Inserts, F5 button: Global mode Send 
Effects, F6 button: Global mode Master Effects, F7 but-
ton: Global mode Instruments, see the separate pdf docu-
ment “Mackie Control and Cubase”.
Use the Locate/Numerics buttons to set the project cur-
sor position.
 Immediately after you enter a numeric character, the Mackie 
HUI time display will no longer show the project cursor posi-
tion, but the new value.
 You don’t have to enter decimal points, colons, or semicolons 
for a new value.
 Use the CLR button to delete the last character. Holding 
down Shift (in the Keyboard Shortcuts section) and pressing 
the CLR button will delete the new value. 
 Press the Enter button to set the project cursor to the position 
according to the new value.
 Use the “+” and “-” buttons to shift the project cursor position 
forward or backward by the amount of time set with the new 
value.
The three LEDs left of the time display indicate whether 
Bars+Beats (BEATS), a frame based timecode (TIME 
CODE), Feet+Frames (FEET) or Samples (all LEDs off) is 
selected.
In this version of Cubase, the following functions have 
been added:
F8 button: Selected channel: Instrument
 Page 1 – Select instrument
 Page 2-n – Instrument parameter
Radikal Technologies SAC-2K
The SAC-2K can control 32 channels (8 channels at a 
time).
Press the “17–24” and “25–32” buttons to switch from 
one set of eight channels to the next.
Use the “1–8” and “9–16” buttons to shift the fader as-
signment in steps of one channel.
Use the Select button above the master fader to dis-
able/enable the motors.Press the Mute/Solo button (the button on the far left) 
repeatedly to cycle through the assignments for the Mute/
Solo and Select buttons of every channel.
The current assignments are indicated by the LED in the button:
Use the From and To buttons to set the project cursor 
to the position of the left or right locator.
Hold down Shift and press the From or To button to move the left or right 
locator to the current project cursor position. If you hold down Shift and 
press the “” buttons, the project cursor is set to the begin-
ning or the end of the project
Press the Store Marker button to create a marker at the 
project cursor position.
Hold down Shift and press the Store Marker button to open the Marker 
window.
Use the Recall Marker button to move the project cursor 
to the closest marker to the right.
Hold down Shift and press the Recall Marker button to move the project 
cursor to the closest marker to the left.
The Play, Stop, Record, “” transport con-
trols control the equivalent functions in Cubase.
The jog wheel is used to move the project cursor posi-
tion in Cubase.
The Scrub button is currently not supported.
The status of the Num button (in the Software Naviga-
tion section) determines the assignment of the “1” to “0” 
and Enter buttons:
With Num-LED on, use the buttons to set the project cur-
sor position:
 Immediately after you enter a numeric character, the SAC-2k 
time display will no longer show the project cursor position 
but the new value.
 You don’t have to enter decimal points, colons, or semicolons 
for a new value.
 Num button: delete the new value and deactivate locate func-
tionality.
LED status Mute/Solo buttons Select buttons
Off Mute track. Select a single track for de-
tailed settings.
On Solo track. Select a single track.
Blinking Control the status of the 
Write buttons in the 
Cubase mixer.Control the status of the Read 
buttons in the Cubase mixer. 
						

							17
Remote controlling Cubase
 Enter button: set the project cursor to the position according 
to the new value.
 Store Marker button: set the project cursor to the position ac-
cording to the new value, and create a marker at the new 
project cursor position.
With the Num-LED off:
 Use the “1” button for page up (step through pages of one pa-
rameter group).
 Hold down Shift and press the “1” button to jump to the last 
page.
 Use the “6” button for page down.
 Hold down Shift and press the “6” button to jump to the first 
page.
 Press the Enter button to switch the display of names of the 
available parameters in the lower row on or off.
 The function keys “2” to “5”, “7” to “0” and function key com-
binations with the Shift button can be used to access func-
tions in Cubase. Refer to the Cubase operation manual for 
information about how to assign program functions to remote 
controller function keys.
Some of the keys are already pre-assigned (and/but can be 
modified):
“5” button: undo the last operation in Cubase. Hold down 
Shift and press the “5” button to “undo the undo”.
“7” button: copy; hold down Shift and press the “7” button to 
cut.
“9” button: paste.
“0” button: save the current project; hold down Shift and 
press the “0” button to save a backup copy of the current 
project.
Hold down Shift and press the “2”, “3”, “4” or “8” buttons to 
control zooming in the Project window.
Pan button in the Mixer-Mode section: Fader Set mode 
Panning:
 Page 1 – Pan left/right

 Pressing a V-Pot will toggle Monitor for that channel.
High button: Fader Set mode EQ High:

 Page 2 – Frequency 

 Page 4 – Enable
 Pressing a V-Pot will bypass EQs for that channel.
HiMid, LowMid, Low button: Fader Set mode EQ Mid-
High, Mid-Low, Low (same functionality as above).
Snd/Ins 1 button: Fader Set mode Send 1:
 Page 1 – Level
 Page 2 – Enable
 Page 3 – Pre/Post

 Pressing a V-Pot will bypass sends for that channel.
Snd/Ins 2 to 4 buttons: Fader Set mode Send 2 to Send 4 
(same functionality as above). Depending on the Snd/Ins 
button status (above Snd/Ins 1 button) Snd/Ins 1 to Snd/
Ins 4 buttons are assigned to Send 1 to Send 4 or Send 5 
to Send 8.
EQs button (Channel-Strips section): Selected Channel 
mode EQ:
 Page 1 – Gain, Frequency, Q and Enable for the lo band, 
Gain, Frequency, Q and Enable for the lo mid band
 Page 2 – Gain, Frequency, Q and Enable for the hi mid band, 
Gain, Frequency, Q and Enable for the hi band
 Pressing a V-Pot will bypass EQs.
Inserts/Sends button: Selected Channel mode Sends:
 Page 1 – Level for Send 1 to Send 8
 Page 2 – Enable for Send 1 to Send 8
 Page 3 – Pre/Post for Send 1 to Send 8
 Page 4 – Bus for Send 1 to Send 8
 Pressing a V-Pot will bypass sends.
Dynamics button: Selected Channel mode Routing:
 Page 1 – Output Bus, Monitor, Input Bus, Input Gain, Input 
Phase
 Pressing a V-Pot will toggle Monitor.
For a description of the functionalities for the MIDI button: 
Selected Channel mode Inserts, Shift+Inserts/Sends but-
ton: Global mode Send Effects, Shift+Dynamics button: 
Global mode Master Effects, Shift+MIDI button: Global 
mode Instruments, see the separate pdf document 
“Mackie Control and Cubase”.
In this version of Cubase, the following functions have 
been added:
Instrument button: Selected channel mode Instrument:
 Page 1 – Select instrument
 Page 2-n – Instrument parameter 
						

							18
Remote controlling Cubase
Roland MCR-8
The Roland MCR-8 can control 16 mixer channels, plus 
transport control. The “A/B switch” is used to switch be-
tween controlling channels 1–8 and 9–16. The following 
MCR-8 parameters control the equivalent parameters for 
each channel strip:
Fader level, mute, solo and pan.
The following MCR-8 transport controls control the equiv-
alent Cubase functions:
Play, Stop, Record, Rewind, Fast Forward.
Tascam US-428
Specifications
The US-428 can remote control up to 64 mixer channels. 
When the Tascam US-428 device is added in the Device 
Setup dialog, you can open the Remote Status window by 
selecting “Tascam US-428” from the Devices menu.
This indicates which bank (group of eight channels in Cubase) is cur-
rently being controlled by the remote device. To select another bank, use 
the pop-up menu in the window or use the Bank Left/Right buttons on 
the remote device.
The US-428 transport keys will have the equivalent 
functionality in Cubase.
To set markers, hold down “Set” while pressing a loca-
tor key.If you hold down the function key [Null] and move a 
fader, the Select and Rec indicators above the fader will 
indicate whether the fader position is below or above the 
current fader level in Cubase.
If the upper indicator is lit, the fader position on the panel is above the 
fader level in Cubase and vice versa. When both indicators are dark, 
fader positions are matched for that channel.
Cubase mixer
The following US-428 controls will remote control the fol-
lowing mixer parameter for each channel strip:
Fader: volume
Mute/Solo: mute and solo (selected via the Solo switch)
Select: selects channel for editing
Pan-Dial: pan
EQ-Gain
Controls the EQ gain for each band selected with the Low, LoMid, HiMid 
and High buttons. These correspond to the four EQ bands in Cubase, 
starting from the leftmost band.
EQ-Freq
Controls the EQ frequency for each band selected with the Low, LoMid, 
HiMid and High buttons. These correspond to the four EQ bands in Cu-
base, starting from the leftmost band.
EQ-“Q”
Controls the EQ “Q” for each band selected with the Low, LoMid, HiMid 
and High buttons. These correspond to the four EQ bands in Cubase, 
starting from the leftmost band.
Aux 1 to Aux 4 and shuttle wheel: 
The effect send levels for sends 1 to 4. 
The shuttle wheel will act as position shuttle if no Aux 
send button is selected.
Press the activated button to deselect it.
Holding down the “Asgn” button and pressing the Low, 
LoMid, HiMid and High EQ buttons switches the corres-
ponding EQ band “On” button status.
Holding down the “Asgn” button and pressing the Aux1 
to Aux4 buttons switches the corresponding Effect Send 
1–4 “On” button status.
!Before you can initiate remote control operation, the 
MCR-8 “Mode” switch must be set to “4”.
!The MCR-8 does not support “MIDI feedback”, that 
is, the current status of parameters in Cubase is not 
indicated on the MCR-8. Therefore, you only need a 
one-way MIDI connection between the MCR-8 and 
Cubase.
!The US-428 supports “MIDI Feedback”, allowing for 
mute/solo, channel selection, EQ band, Aux 1 to 4 
and transport status to be indicated on the panel. For 
this (and the fader position indication described 
above) to work, you need to select the “US-428 
Control” port as input and output. 
						

							19
Remote controlling Cubase
Yamaha 01V
The Yamaha 01V can remote control Cubase. Before you 
can initiate remote control operation, the 01V must be set 
up in the following way:
MIDI Parameter Change and Receive must be enabled.
MIDI Control Change and Receive must be disabled.
Device ID / MIDI Channel Receive must be set to “1”.
Local Control should be set to “Off”.
As soon as Local Control is set to “Off”, remote control is enabled.
The 01V remote operation of Cubase is very straightfor-
ward, with (almost) every parameter having the equivalent 
parameter controller in the 01V mixer. The current status 
of all controllable parameters is fed back to the 01V and 
indicated on the panel, using the motorized faders, indica-
tors, etc. (for this to work, you need a two-way MIDI con-
nection between the 01V and Cubase).
To facilitate 32 channel remote control, two separate con-
trol “Layouts” are used, each controlling 16 mixer chan-
nels. The “Memory” button on the 01V is used to switch 
between VST layout 1 and 2. Page 1 displays VST Layout 
1, and page 2 VST Layout 2.
The following parameters are remote controllable for 
channels 1–32 in the mixer:
Fader level, mute and pan.
01V controls for these parameters control the equivalent Cubase param-
eters.
Effect sends 1–6.
01V Aux 1–4 control effect send 1–4, 01V effect 1 and 2 control effect 
send 5 and 6.
EQ Frequency, Gain and Q (4 bands).
01V controls for these parameters control the equivalent Cubase param-
eters.
Stereo Master Volume.
The 01V control for this parameter controls the equivalent Cubase pa-
rameter.
Send effects master volume 1–4 are controlled by 01V 
Aux Master 1–4. Send effects master 5 and 6 are con-
trolled by 01V effect master 1 and 2.With Layout 1 the 01V controls the following channels:
Channel 1–12, 13/14 and 15/16 will control channels 
1–14.
01V Return 1 and 2 will control channels 15 and 16.
With Layout 2 the 01V controls the following channels:
Channel 1–12, 13/14 and 15/16 will control channels 
17–30.
01V Return 1 and 2 will control channels 31 and 32.
Yamaha DM2000/DM 2000v2
The Yamaha DM2000 is a digital mixing console that pro-
vides full automation of virtually all console parameters. It 
is designed to integrate effectively with digital audio work-
stations such as Cubase.
For detailed information about features, parameters, 
etc., please see the documentation which comes with the 
Yamaha DM2000.
In this version of Cubase, the following functions have 
been added:
Automix Section
[Auto]: write enable
[Set] + [Auto]: read enable
Studio 1–4 added as [Aux9]–[Aux12] to the DM2000 - 
Operation is identical to Sends (volume, on/off, pre/post 
supported)
Matrix [Aux9]–[Aux12] will assign Studio 1–4 to the en-
coders above the faders
Selected Channel Aux9–12 will assign Studio 1–4
!The value ranges for the parameters in the 01V may 
not match the ranges for the corresponding parame-
ters in all cases.
User defined 
keysDM 2000 Button Cubase function
#3 Abort Drop out mode Touch
#4 Auto rec Drop out mode Latch
#5 Return Drop out mode X-Over
#6 Relative Trim mode
#7 Touch sense Toggle Write Enable All Tracks 
						

							20
Remote controlling Cubase
Yamaha DM1000v2
The Yamaha DM1000v2 is a digital mixing console that 
provides full automation of virtually all console parameters. 
It is designed to integrate effectively with digital audio 
workstations such as Cubase.
For detailed information about features, parameters, 
etc., please see the documentation which comes with the 
Yamaha DM1000v2.
Yamaha 01v96v2
The Yamaha 01v96v2 is a digital mixing console that pro-
vides full automation of virtually all console parameters. It 
is designed to integrate effectively with digital audio work-
stations such as Cubase.
For detailed information about features, parameters, 
etc., please see the documentation which comes with the 
Yamaha 01v96v2.
Yamaha 02r96v2
The Yamaha 02r96v2 is a digital mixing console that pro-
vides full automation of virtually all console parameters. It 
is designed to integrate effectively with digital audio work-
stations such as Cubase.
For detailed information about features, parameters, 
etc., please see the documentation which comes with the 
Yamaha 02r96v2.
Yamaha 01x
The Yamaha 01x is a digital mixing console that provides 
full automation of virtually all console parameters. It is de-
signed to integrate effectively with digital audio worksta-
tions such as Cubase.
For detailed information about features, parameters, 
etc., please see the documentation which comes with the 
Yamaha 01x.
In this version of Cubase, the following functions have 
been added:
[Shift]+[Send FX]: Studio Sends for selected channel
 Page 1 – Level
 Page 2 – Enable

 Page 4 – Pan Left/Right
[Instruments]: Instrument for selected channel (Instrument 
tracks and MIDI track to VSTi from the Rack)
 Page 1 – Select instrument
 Page 2-n – Instrument parameter
 [Shift]+[Instruments]: VST Instrument Rack access (as v3.x)