Home
>
Standard Horizon
>
Communications receiver
>
Standard Horizon Receiver MST660 Operating Instructions
Standard Horizon Receiver MST660 Operating Instructions
Here you can view all the pages of manual Standard Horizon Receiver MST660 Operating Instructions. The Standard Horizon manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 1
MST660 Marine Compact Disc Stereo System Owners Manual HORIZON Marine Electronics ¥AM/FM CD Player ¥Removable Front Panel ¥Water Resistant Housing ¥18FM & 12AM Presets ¥8 Times Oversampling ¥Intro, Repeat & Random Play MST660 I.M.-2 21/12/99 1:26 PM Page 1
Page 2
TABLE OF CONTENTS FEATURES.........................................................................................1 PRECAUTIONS..................................................................................2 CONTROLS........................................................................................3 REMOVING AND FITTING THE FRONT PANEL..............................5 INSTALLATION..................................................................................6 Location and...
Page 3
MST660 OwnerÕs Manual Page 1 FEATURES ¥Detachable face panel: Guards against theft by allowing you to remove the face panel, rendering the stereo unusable. A carry case for the detachable face panel is included. ¥All Electronic Controls:The Bass, Treble, Volume, Balance and Fader functions are all controlled by touch buttons for greater long term reliability. ¥8 Times Oversampling Digital...
Page 4
PRECAUTIONS ¥If you are connecting your MST660 for the first time or have just reconnected your boat battery and you are experiencing problems with the MST660Õs operation, we suggest you try resetting the unit. The reset button is located under the removable face panel (see page 5 for instructions on removing and refitting the face panel). Simply press the reset button with a ball point pen or similar. You can then refit the face panel. ¥Do not insert anything other than audio compact discs into the disc...
Page 5
CONTROLS 1.SELect Button: Press to select the next available control. The options available are Volume, Bass, Treble, Balance and Fader. 2. +Control Button:Increases the setting of the selected control (Volume, Bass, Treble, Balance or Fader). 3. ÐControl Button:Decreases the setting of the selected control (Volume, Bass, Treble, Balance or Fader). 4.Press BNDto set the frequency band to FMI, FMII, FMIII, AMI or AMII. 5 & 6. TUNE Buttons. ¥In Radio mode, the TUNE buttons are used to manually...
Page 6
¥In CD Program mode, press or to select a track number for programming. ¥In Clock setting mode, press to change the minutes and to change the hours. 7.Press the SCN(Scan) button to play the first 10 seconds of each track on the CD. 8.The RPT(Repeat) button causes the current track on the CD to be played repeatedly. 9.The RPT A-B(Repeat Selection) button allows a selection of music on the CD to be played repeatedly. 10.Press the RDM(Random) button to play all the tracks on the CD...
Page 7
REMOVAL AND FITTING THE FACE PANEL Removal Before removing the face panel, turn the unit OFF by pressing the PWR button. 1.Press the release button to release the left-hand end of the face panel. 2.Lift the front panel out towards you. After removing the face panel, place it inside the supplied case to protect it from damage. Do not leave it in a position where it could be exposed to direct sunlight. Refitting 1.Make sure the face panel is the right way up as it cannot be attached upside down....
Page 8
Page 6 OwnerÕs Manual MST660 INSTALLATION Location The MST660 is designed to be mounted in several different ways to enable it to be installed in the most convenient position. Although the unit is water resistant when the front cover is closed, care should be taken to locate it where it will not be subjected to spray or rain. The unit should be mounted with an angle of less than 20¡to the...
Page 9
MST660 OwnerÕs Manual Page 7 Flush Mounting The MST660 can be neatly flush mounted into a panel or bulkhead so that just the controls and the protective cover are visible. There are two flush mounting options available. The best option for you will depend on your particular situation. ¥If the space behind the bulkhead or panel you have selected has a suitable support shelf and the area is...
Page 10
Page 8 OwnerÕs Manual MST660 4.If your measurements are correct, carefully cut the slot around the marked lines, ensuring that you maintain the curves in each corner. Mark and drill the four 0.08 holes in the bulkhead to accept the locating pins at each corner of the escutcheon. 5.Trial fit the escutcheon to ensure it fits securely against the panel. If all is well, place a small dab of...