Standard Horizon Marine Tranciever Quantum GX2360S Operating Instructions

Page 41 GX2360S[
CALL/SET(
MENU)]
 key to move to the next space.
This method can also be used to enter a blank space
in the name. To clear the previous letter, press the
[
H/L(
NAV)]
 key.
9. After the eleventh letter or space has been entered, press the [
CALL/
SET(
MENU)]
 key to advance to the MMSI (Maritime Mobile Service Iden-
tity Number) number entry.
10. Turn the CHANNEL selector knob to scroll through numbers, 0-9. To enter
the desired number and move one space to the right press the
[...

GX2360SPage 42lected setting.
7. To exit this menu and return to radio operation mode
press the [
16/9]
 key.
7.7.3  Setting up Individual Call Ringer
When a Individual call is received the radio will produce a ringing tone for 3
minutes. This selection allows the Individual Call ringer time to be changed.
1. Press and hold down the [
CALL/SET(
MENU)]
 key
until “RADIO SETUP” menu appear.
2. Turn the CHANNEL selector knob to select “DSC
SETUP” menu.
3. Press the [
CALL/SET(
MENU)]
 key, then select...

Page 43 GX2360S
will transmit again.
7. After the second INDIVIDUAL CALL is transmitted,
if the reply signal is not received, the dot matrix area
of the LCD will display “SEND” to prompt the user
to send the call again or exit the mode.
8. When an individual call acknowledgment is received,
the established channel is automatically selected and
a ringing tone sounds.
9. Press the [
CALL/SET(
MENU)]
 key to listen to the
channel to make sure it is not busy, then key the
microphone and call the other...

GX2360SPage 44 1. Press and hold down the [
CALL/SET(
MENU)]
 key
until “RADIO SETUP” menu appears.
2. Turn the CHANNEL selector knob to select “DSC
SETUP” menu.
3. Press the [
CALL/SET(
MENU)]
 key, then select
“INDIV ACK” with the CHANNEL selector knob.
4. Press the [
CALL/SET(
MENU)]
 key.
5. Turn the CHANNEL selector knob to select “ABLE”
or “UNABLE.”
6. Press the [
CALL/SET(
MENU)]
 key to store the se-
lected setting.
7. To exit this menu and return to radio operation mode
press the [
16/9]
 key....

Page 45 GX2360S
reference in the directory.
7. Press the [
CALL/SET(
MENU)]
 key to store the first
letter in the name.
8. Repeat step 6 and 7 until the name is complete.
The name can consist of up to eleven characters, if
you do not use all eleven characters press the
[
CALL/SET(
MENU)]
 key to move to the next space.
This method can also be used to enter a blank space
in the name. To clear the previous letter, press the [
H/L(
NAV)]
 key.
9. After the eleventh letter or space has been entered, press...

GX2360SPage 46
8. After the GROUP CALL is transmitted, all the radios
in the group will switch to the designated channel.
9. Listen to the channel to make sure it is not busy,
then key the microphone and call the other vessels
you desire to communicate with.
7.8.1.3 Receiving a Group Call
1. When a group call is received, the QUANTUM will produce a ringing alarm
sound.
2. The radio automatically switches to the requested channel.
3. Press any key to stop the alarm.
4. Monitor the channel for the person...

Page 47 GX2360S
7.8.2.1 Setting up Position Reply
The QUANTUM can be set up to automatically or manually send your position
to another vessel. This selection is important if you are concerned about some-
one polling the position of your vessel that you may not want to. In the manual
mode you will see the MMSI or persons name shown on the display allowing
you to choose to send your position to the requesting vessel.
1. Press and hold down the [
CALL/SET(
MENU)]
 key
until “RADIO SETUP” menu appear.
2....

GX2360SPage 48 6. After a DSC position request is transmitted, the trans-
ceiver remains on channel 70 until position data is
received from the polled vessel.
7. When the QUANTUM receives the position from the
polled vessel it is shown on the radio display and
also transferred to the GPS Chart plotter.
8. If the QUANTUM does not receive a reply, the LCD
will display “SEND” to prompt the user to send
the call again or exit the mode.
NOTE
If the QUANTUM does not receive position data from the polled...

Page 49 GX2360S
7.8.3  Position Send
The feature is similar to Position Request, however instead of requesting a
position of another vessel this function allows you to send your position to an-
other vessel. Your vessel must have an operating GPS receiver connected for
the QUANTUM to send the position.
NOTE
To transmit a Position Send Call, you must setup the QUANTUM DSC
Individual / Position Call Directory with the name of the vessel(s) or per-
son and the MMSI of the DSC radio you wish to send your...

GX2360SPage 50
8  RADIO SETUP
NOTE
The optional RAM+ MIC CMP25 can also change the SETUP menu.
Refer to page 60 for details.
8.1  LAMP ADJUSTING
Allows setting up the backlight intensity or to turn it off.
1. Press and hold down the [
CALL/SET(
MENU)]
 key
until “RADIO SETUP” menu appears.
2. Press the [
CALL/SET(
MENU)]
 key, then select
“LAMP” in the “RADIO SETUP” menu with the
CHANNEL selector knob.
3. Press the [
CALL/SET(
MENU)]
 key.
4. Turn the CHANNEL selector knob to select the de-
sired level....