Sony Vpl Aw15 Projector User Manual

51 
Others
This section describes how to solve the problems, how to replace the lamp and air filter, 
etc.
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem 
using the following instructions. If the problem persists, consult with qualified Sony 
personnel.
Power
Picture
Others
Symptom Cause and Remedy
The power is not turned on.cAfter about 1 minute, turn the power on. 
cClose the lamp cover securely, then tighten the screws securely. 
(1 page...

 52
On-screen display
Remote control
Others
Symptom Cause and Remedy
The picture is too dark.cAdjust the contrast or brightness of the Picture   menu 
properly. (1 page 41)
The picture is not clear.cAdjust the focus using the focus ring. (1 page 24)
cCondensation has accumulated on the lens. Leave the projector 
for about 2 hours with the power on.
The picture flickers.cActivate “APA”, then adjust the current input signal.
cAdjust “Phase” for “Adjust Signal” in the Screen   menu 
properly. (1 page 45)...

53 
Others
The ?/1 (On/standby) or LAMP/COVER indicator lights up or flashes if there is any 
trouble with your projector.
When a warning indicator other than the above status, consult with Sony Customer Information 
Service Center.
Warning Indicators
Symptom Cause and Remedy
LAMP/COVER flashes in 
red. (A repetition rate of 2 
flashes)cClose the lamp cover securely, then tighten the screws securely. 
(1 page 56)
cClose the air filter cover securely. (1 page 57)
LAMP/COVER flashes in 
red. (A repetition...

 54
Warning messages
Caution messages
Message Lists
Message Cause and Remedy
High temp.! Lamp off in 1 
min.cTurn off  the power.
cCheck to ensure that nothing is blocking the ventilation holes. 
(1 page 13)
Frequency is out of range!cFrequency is out of range. Input a signal that is within the 
acceptable frequency range of the projector.
Please check Input-A 
Signal Sel.cSet “Input-A Signal Sel.” in the Setup   menu to 
“Computer” when an RGB signal is input from a computer. 
(1 page 47)
Please replace...

55 
Others
Replacing the Lamp 
and the Air Filter and 
cleaning the 
Ventilation holes 
(intake)
Tools you need to get started:
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes strange, 
or “Please replace the Lamp/Filter.” appears 
on the screen, the lamp may be exhausted. 
Replace the lamp with a new one (not 
supplied) 
without delay.
Use an LMP-H160 Projector Lamp as...

 56
4Loosen the three screws on the 
lamp with the Phillips 
screwdriver. Hold up the handle, 
then pull the lamp straight out.
5Hold the handle of the new lamp 
and push it in securely until it 
reaches the end, and then 
tighten the 3 screws.
 Be careful not to touch the optical block 
inside the unit.
 If the 3 screws are not tightened 
securely, the lamp cover will not close.
6Close the lamp cover, then 
tighten the screws.
If the lamp cover is not set securely, the power 
will not turn on.
7Remove...

57 
Others
9Place a new air filter.
After removing the air filter, do not touch 
the fan inside the projector.
10Attach the air filter cover.
11Wipe dust off the Ventilation 
holes (intake) with a soft cloth.
The projector will not turn on unless the air 
filter cover is securely closed.
12Place the project back on its 
original position.
13Turn on the projector, then 
select the desired setting item 
on the Setup  menu. The 
menu screen below will be 
appeared.
14Select “Yes”.
15Select “OK”.
Do not put...

 58
Replacing the Air 
Filter
When “Please replace the filter.” appears on 
the screen, you should replace the air filter.
The air filter should be replaced every 1,500 
hours. This value varies depending on the 
environment or how the projector is used. 
1,500 hours are approximate.
 For details on how to attach and remove the 
air filter, see “Replacing the Lamp and the 
Air Filter and cleaning the Ventilation holes 
(intake)” Steps 7 to 11. (1 page 56)
 When you remove the air filter, be careful 
not...

59 
Others
Specifications
System
Projection system
3LCD panel, 1 lens, 3 primary 
color LCD shutter projection 
system
LCD panel 0.73-inch (18.5 mm) TFT LCD 
panel 2,764,800 pixels (921,600 
pixels × 3)
Lens 1.6 times zoom lens (manual) 
f=21.3 to 34.1 mm/F2.4 to 3.1
Lamp 165 W Ultra High Pressure Lamp 
Projection picture size
40 to 200 inches (measured 
diagonally)
Color system NTSC
3.58/PAL/SECAM/NTSC4.43/
PAL-M/PAL-N/PAL60 system, 
switched automatically/
manually (PAL60 system not 
switched...

 60
Supplied accessories
Remote control 
RM-PJAW15 (1) 
(VPL-AW15 only)
RM-PJAW10 (1) 
(VPL-AW10 only)
Size AA (R6) batteries (2)
AC power cord (1)
Air filter (for replacement) (1)
Lens Cap (1)
Operating Instructions (1)
Design and specifications are subject to change 
without notice.
Optional accessories
Projector Lamp LMP-H160 (for replacement)
Projector Suspension Support PSS-H10, PSS-610