Sony Vaio Sony Vaio Vgnx505 Manual

							X505 SeriesConfidential
Chapter 1. Disassembly & Assembly Guide
1.MS-1-D.1
1-3. Disassembly & Assembly
- Main Section -
MS-1Main Section Disassembly 
						

							X505 SeriesConfidential
Battery Pack
Slide the Levers toward the center.
In the state 1), pull the Battery Pack in the arrow direction.
Battery Pack
1)
2)
1.MS-1-D.2 
						

							X505 SeriesConfidential
Dummy Card
Put the Main Section with its left side toward you.Push the Eject Lever twice.
Pull out the Dummy Card.
First time Second time
Eject Lever
2)
3)
1)1.MS-1-D.3 
						

							X505 SeriesConfidential
Cap (Hinge)Widen the Detents (at three locations) outward with a bamboo skewerto remove.
 Remove the Cap (at two locations) by sliding as it is outward.
DC Jack side Power Button side
Cap
Remarks* If not disassembling the LCD Section, this work is not required.1)
2)1.MS-1-D.4 
						

							X505 SeriesConfidential
Stopper (Hinge)
Peel off the Foot (at two locations).
Release the Stopper (at two locations).
*The Detents in the near side are fit. Raise them forward and pull out.
Stopper
Foot
1) 2)
3)
Remove the Screws (two locations).
*In the 1st Models, the types of Screw differ  between the left and the right.
Screw : B4
1.MS-1-D.5
Screw: 
1st Model - B5(
Special Screw
)
B4
2[MA]
5[CHG] 
						

							X505 SeriesConfidential
Cover (Hinge)Widen the Detents (at two locations) with a bamboo skewer outwardto remove.
* The Covers may be easily broken. Work with care. In the state 1), slide the Cover (two locations) to remove.
Detent positions
Cover
Remarks
LCD Side
LCD side
1)
2)1.MS-1-D.6 
						

							X505 SeriesConfidential
Housing (Bottom)-1
Open the Main Section till the LCD Section and the Bottom Section 
are in the right angle.
Remove the Screws (two locations) from the back face of the Main Section. 
Remove the Screws (two locations) from the left side of the Main Section. 
Screw : B6
Screw : B4
Peel off the Foot (at six locations).
* Give a care not to damage the Housing (Bottom).
* Two kinds of Foot are provided.
1)
2)
3) 4)
* Also refer to the next page.
1.MS-1-D.7 
						

							X505 SeriesConfidential
Housing (Bottom)-2
Raise the Housing (Bottom) at its near side.
*Release the Detents (two locations) by pushing the Palmrest lightly toward the center.
Remove the eleven Screws from the bottom of the Main Section.
* The Screws B3 and B5 are the special screws.
Screw  B5 (X4) , B3 (X4), B4(X2), B2 (X1)
B3
B5
B4
B2
B5 B5
B5
B3
B3 B3
Remove the Housing (Bottom) by pulling it toward you.
* The back side is inserted in the Palmrest.
B4
Detent
Detent
Housing (Bottom)
Work desk
LCD Section
Place the Main Section on the work desk as shown in the picture.
*Work with a great care not to fall the Main Sectionor to damage the LCD!
5) 6)
7) 8)1.MS-1-D.8 
						

							X505 SeriesConfidential
LCD Section
Remove the Cover (one location).
Cover (Harness)
Disconnect the Harness (at three locations) in the order from A to C.
* Take out the Harness from under the Mother Board and pull it to remove.(A: LCD Harness/ B: Harness (INV) / C: Harness (DC) )
A
B
C
Disconnect the Harness (PWR) (one location).
*Take out the Harness from under the FPC and pull it in the   arrow direction.
Remove the one Screw and remove the LCD Section.
*Work with great care not to damage the LCD Section!
* The Protect (Harness) may be displaced from the Hinge (Left).
Screw : B4
1) 2)
3) 4)1.MS-1-D.9
FPC 
						

							X505 SeriesConfidential
Disconnect the FPC (at two locations).
* Pull it upward to disconnect.
HDD
Pull the HDD in the arrow direction to remove.
Remark 1
FPC
Cushion
Sheet
Gasket
The above parts are installed on the HDD.* Be careful not to bend the Pin when disconnecting the FPC.
FPC
Remark 2
1)
2)1.MS-1-D.10
FPC