Sony Vaio Sony Vaio Vgntx Manual

							TX Series
Confidential
Optical Disc Drive-1
1)2)1.MS-1-D.8
Insert a thin tool into the hole of the Bezel, push it lightly 
and draw out the tray.
Bezel
Tray
Screw: Blue-B5/Red-B2
Remove the four screws.
Optical Drive
Tape (Common)
Peel off the Tape (one place).
Red
RedRed
Blue
4)
Optical Disc Drive
Disconnect the FPC (one place). 
*1st, 2nd Model --- Pull out it upward. 3rd Model --- Raise the lock lever to release the lock, and disconnect it in the direction of the arrow.
1st,2nd Model
Lock Lever
FPC
1
2
3)
1st,2nd,3rd Model
16
[MA]
Other Model10
[MA]
16
[MA] 
						

							TX Series
Confidential
Optical Disc Drive-2
5)1.MS-1-D.9Raise the front side of the Optical Disc Drive, and remove it toward the front. 
* The convex portion is engaged.
Optical Disc Drive
Convex Portion 
						

							TX Series
Confidential
LCD Section-1
1)1.MS-1-D.103)
Disconnect the connectors of the coaxial cables directly above.
Pull out the Harness (LCD) directly above and disconnect it.
Tape (Harness)
Peel off the Tape (Harness).
Harness (LCD)
2)
Coaxial Cable
1st,2nd Model
Other Model10
[MA]
16
[MA] 
						

							TX Series
Confidential
LCD Section-2
4)1.MS-1-D.11
Remove the two screws, and then the LCD Section.
* Hold the LCD Section with your hand not to fall down. 
* Release the coaxial cables from the main unit beforehand.
Screw: B5 
						

							TX Series
Confidential
IFX-421 Board-1
1.MS-1-D.123) 4)
Peel off the Sheet and Insulator from the IFX Board.Remove the one screw.
+
Screw: B2
Peel off the Cushion.
Cushion (KBMS)
Peel off the Insulator.
1)
Sheet (Fan)
Insulator(MDCR)
IFX Board
1st, 2nd, 3rd Model
16
[MA]
2)
Insulator(MDCR)
1st, 2nd, 3rd Model
16
[MA] 
						

							TX Series
Confidential
IFX-421 Board-2
5)1.MS-1-D.13
Remove the IFX Board.
6)
Release the lock, and remove the FPC in the direction of the arrow. 
* Raise the lock lever, and the lock is released.
1
Lock Lever
2
IFX Board 
						

							TX Series
Confidential
Parts of the IFX-421 Board
1)2)1.MS-1-D.143)
Raise the lock lever to release the lock, and remove 
the FPC in the direction of the arrow. Remove the one screw, and then the Modem Card. 
* The Harness is hooked on the notch.
FPC-30
Lock Lever1
2
Modem CardScrew: B5
Harness
Notch
Harness (RJ11)
Disconnect the Harness in the direction of the arrow.Modem Card 
						

							TX Series
Confidential
Harness (DC Jack)/CNX-338 Board
1)2)1.MS-1-D.153)
Pull out the Harness in the direction of the arrow 1, and 
remove the Harness (DC Jack) toward the front. Remove the one screw.
Raise the front side of the CNX Board lightly (arrow  1), and take out it 
toward the front (arrow  2). Then pull out the FPC directly above and 
remove the CNX Board (arrow  3).
1
Harness (DC Jack)
Connector Portion
2
Screw: B2
1
3 2
CNX BoardFPC 
						

							TX Series
Confidential
Mother Board-1
1)2)1.MS-1-D.163) 4)
Peel off the Sheet (PR).
Sheet (PR)
Pull out the FFC (two places).
MBX
WWAN Unit
FFC 3
WAN Model
2[MA]
Peel off the Tape (one place).
Tape (MW)
2[MA]
WAN / TV Model
5[MA]
MDL Board
FFC 24P (MDL-17)
Mother Board
Disconnect the FFC (two places).
TV Model
5[MA] 
						

							TX Series
Confidential
Mother Board-2
5)1.MS-1-D.177) 8)
Disconnect the Harness (Reserve Battery) in the direction of 
the arrow, and remove the Reserve Battery.
* It is secured with adhesive tape.
Reserve Battery
Disconnect the FPC directly above.
FPC
6)
Raise the lock lever to release the lock, and remove the FPC.
Lock Lever
12
FPC
2nd Model
Sheet (FPCPC)
Coil
5[MA]
Peel off the Sheet from the coil (two places).
FPC
1st,2nd Model
10
[MA]