Sony Uda1 Manual

2.  Replace the lithium battery CR2025 with a new one,  with the +  side facing up.
3.  Place  the battery case back in position.
Note
Keep the lithium battery out of the reach  of children.
Should the battery be swallowed, immediately consult a doctor.
[13] How  to UsePreparations and connectionsPreparations
Standby mode
If you switch the AUTO STANDBY  switch on the rear panel  of the USB DAC AMPLIFIER to “ ON, ” when
you are  not using the USB DAC AMPLIFIER or there is  no digital signal input to the...

Even when no digital audio  is  input,  the USB DAC AMPLIFIER may not switch to standby  mode  due
to the operation of other devices connected, or due to connection/disconnection  of the cables.
Hint
When the USB DAC AMPLIFIER is  in standby  mode, you can start  the USB DAC AMPLIFIER only by
pressing the 
 button on the remote control  or the unit.
[14] How  to UsePreparations and connectionsConnections
Connecting speakers
Connect  speakers to the USB DAC AMPLIFIER, then  connect  the supplied  AC power...

Note
Switch  the EQUALIZER switch to “BYPASS” when you use speakers other than  the recommended
SS-HA3  speakers (not  supplied).
[15] How  to UsePreparations and connectionsConnections
Connecting to a computer
Connect  a USB port  of your  computer to the  (USB)  port  on the rear panel  of the USB DAC
AMPLIFIER using the USB cable (supplied), then  start  up your  computer.
Note
Make  sure  that the USB DAC AMPLIFIER is  turned off when you connect  a USB cable.
When a signal of a format not supported...

FRONT lamp flashes quickly. Check whether there is  a problem with the device connected.
Music files stored on a USB thumb drive,  etc., cannot  be played  back.
Hint
The  device is  charged when connected to the USB DAC AMPLIFIER while the USB DAC AMPLIFIER
is  turned on.
If a device that is  not supported  has a headphone  output jack, you may be able to play back music
files by connecting the headphone  output jack of the device and the LINE  IN jacks of the USB DAC
AMPLIFIER. For details on how to...

: Walkman that supports High-Resolution  Audio
: WM-PORT (22  pin)
: High-Resolution  Audio USB Adaptor  WM-PORT Cable (WMC-NWH10, not supplied)
: USB cable (supplied)
:  (USB)  port  of the USB DAC AMPLIFIER
[18] How  to UsePreparations and connectionsConnections
Connecting other playback equipment
You can connect  other playback  equipment such as the Super Audio CD  player  to the USB DAC
AMPLIFIER and enjoy playback  from that equipment through the speakers or headphones  of the USB
DAC AMPLIFIER....

When connecting through the COAXIAL jack
: COAXIAL  jack of the USB DAC AMPLIFIER
: Coaxial digital cable (not  supplied)
: Coaxial digital output jack of other equipment
When connecting through the OPTICAL  jack
: OPTICAL  jack of the USB DAC AMPLIFIER
: Optical digital cable (not  supplied)
: Optical digital output jack of other equipment
When connecting through LINE IN jacks
: LINE  IN jacks of the USB DAC AMPLIFIER
: Audio cord  (not  supplied)
: Analog output jack of other equipment
[19] How  to...

: PHONES  jack of the USB DAC AMPLIFIER
: Headphones
[20] How  to UsePlaying audio  filesPlayback
Compatible audio formats
The  audio  formats that the USB DAC AMPLIFIER can decode depend on the digital audio  input jacks of
the equipment connected.
The  USB DAC AMPLIFIER supports the following audio  formats.
USB REAR (USB-B jack)
PCM  (Sampling  frequency: 44.1  k/48 k/88.2  k/96 k/176.4 k/192  kHz, data  bit length:  16/24/32 bits)
DSD (2.8  M/5.6  MHz)
USB FRONT (USB-A jack)
PCM  (Sampling...

2.  Turn on the equipment and start  playback.
When you want to play back music files stored on the computer,  play back those  music files with
the music player  software you are  currently using.
3 .  Turn the VOLUME  +/– control  to adjust the volume.
You can also adjust the volume  by pressing the VOLUME  +/– button on the remote control.
Note
Sound may be interrupted when the sampling  frequency or audio  format is  changed.
[22] How  to UsePlaying audio  filesSound quality settings
Using the DSEE...

DSEE  stands  for Digital Sound Enhancement Engine, a high range compensation  technology
developed independently  by Sony.
1 .  Press the DSEE  button on the remote control.
During  playback  using the DSEE  function, the DSEE  lamp is  lit.
To cancel the DSEE  function, press  the DSEE  button again.
Note
When you select an input source  or input signal that is  not supported,  the DSEE  function  setting
cannot  be changed. If you press  the DSEE  button when the DSEE  function  setting  cannot  be...

1. (ON/STANDBY) button
Turns the USB DAC AMPLIFIER on and off.
2 .  Power lamp
When the USB DAC AMPLIFIER is  turned on, this lamp lights up in green.
The  lamp turns  off when the USB DAC AMPLIFIER is  in standby  mode.
3 .  Input  indicator lamps
The  lamp of the input source  selected  lights up.
4 .  INPUT SELECTOR button
Press this button repeatedly to select an input source.
5 .  MUTING  lamp
Lights up in amber when the muting  function  is  active.
6 .  DSEE  lamp
Lights up in blue when the DSEE...