Sony Rht G950 Operating Instructions

							41GB
Additional Information
If you experience any of the following 
difficulties while using the stand, use this 
troubleshooting guide to help remedy the 
problem before requesting repairs. Should any 
problem persist, consult your nearest Sony 
dealer.
General
The power is not turned on.
 Check that the AC power cord (mains lead) 
is connected securely.
If “PROTECTOR” and “PUSH POWER” 
appears alternately in the front panel display.
Press ?/1 to turn off the stand, and check the 
following item after “STANDBY” disappears.
 Is anything blocking the ventilation holes of 
the stand?
After checking the above item and fixing 
any problems, turn on the stand. If the cause 
of the problem cannot be found even after 
checking the above item, consult your 
nearest Sony dealer.
Dolby Digital or DTS multi-channel sound is 
not reproduced.
 Check that the playing Blu-ray Disc, DVD, 
etc., is recorded in Dolby Digital or DTS 
format.
 When connecting the Blu-ray Disc, DVD 
player, etc., to the digital input jacks of this 
stand, check that audio setting (settings for 
the audio output) of the connected 
component.
The surround effect cannot be obtained.
 Depending on the digital signal, the 
surround processing may not work 
(page 28).
No sound or only a very low-level sound is 
heard from the speakers.
 Press VOLUME + and check the volume 
level.
 Press MUTING or VOLUME + to cancel the 
muting function.
 Press SOUND FIELD +/– and check the 
selected sound field.
 Depending on the source, the sound effect of 
the speakers may be less noticeable.
Sound lags behind the TV image.
 Set “A/V SYNC” to “OFF” when “A/V 
SYNC” is set to “ON.”
Connected components
There is no sound or only a very low-level 
sound no matter which component is selected.
 Check that this stand and components are 
connected correctly and securely.
 Check that both this stand and the selected 
component are turned on.
There is no sound from the selected 
component.
 Check that the component is connected 
correctly to the audio input jacks for that 
component.
 Check that the cords are fully inserted into 
the jacks on both the component and this 
stand.
 Check that the component is selected 
correctly.
Sound is interrupted or there is noise.
 Check “Formats supported by this stand” 
(page 44).
No image appears on the TV.
 Check that the TV is selected correctly.
 Set the TV to the appropriate input mode.
 Check the HDMI connection.
 Check that the cords are fully inserted into 
the jacks on both the component and this 
stand.
Additional Information
Troubleshooting
continued
 
						

							42GB
Control for HDMI
If you experience any of the following 
difficulties while using the “BRAVIA” Sync, 
use this troubleshooting guide to help you 
remedy the problem.
The Control for HDMI function does not work.
 Check the HDMI connection (page 13).
 Make sure “CTRL: HDMI” is set to “ON” in 
AMP menu.
 Make sure the connected component is 
compatible with the Control for HDMI 
function.
 Check the Control for HDMI settings on the 
connected component. See the operating 
instructions supplied of the connected 
component.
 If you change the HDMI connection, 
connect/disconnect the AC power cord 
(mains lead), or there is a power failure, 
repeat the procedures of ““BRAVIA” Sync 
Features” (page 31).
 The stand may not work correctly if you 
select a component that is not compatible 
with the Control for HDMI function on the 
TV side.
No sound is output from the stand and TV 
speaker.
 Check the volume of the stand and the TV.
 Select the input of the stand correctly.
The sound is output from both the stand and 
the TV.
 If the Control for HDMI function is set to 
off, or the selected component is not 
compatible with the Control for HDMI 
function, turn off the sound of the stand or 
the TV.
The System Power Off function does not work.
 Change the setting of the TV to turn 
connected components off automatically 
when you turn off the TV. For details, refer 
to the operating instructions of the TV.
The stand is turned off when you turn off the 
TV.
 When the Control for HDMI function is on, 
the System Power Off function is active, and 
the stand is turned off when you turn off the 
TV.
An image does not appear on the TV.
 Check whether HDMI IN and HDMI OUT 
are connected in reverse.
When the stand is in standby mode, there is no 
image or sound on the TV.
 When the stand is in standby mode, image 
and sound are output from the HDMI 
component selected the last time you turned 
off the stand. If you are enjoying other 
component, play the component and 
perform the One-Touch Play operation, or 
turn on the stand to select the HDMI 
component you want to enjoy.
 Make sure “POWER SAVE” is set to “OFF” 
in the AMP menu if you connect 
components not compatible with the 
“BRAVIA” Sync to the stand (page 35).
OTHER
The remote does not function.
 Point the remote at the remote sensor   on 
the stand.
 Remove any obstacles in the path between 
the remote and the stand.
 Replace both batteries in the remote with 
new ones, if they are weak.
 Make sure you select the correct input on the 
remote.
The volume turns down when the output 
method changes from the TV speaker to the 
stand speaker.
 The Volume Limit function is working. For 
details, refer to “Using the Volume Limit 
function” (page 34).
 
						

							43GB
Additional Information
If the stand still does not operate 
properly after performing the 
above measures, reset the stand 
as follows:
Use buttons on the stand for the operation.
1Press ?/1 to turn on the power.
2Press ?/1 while pressing INPUT 
SELECTOR and VOLUME –.
“COLD RESET” appears and the stand is 
reset. AMP menu, sound field etc., return to 
the default settings.
* The shelf board can be installed at three levels (1, 
2 or 3).
Specifications
Dimensions: 
mm (approx.)A1,115
B400
C500
Adjustable shelf 
dimensions*:
mm (approx.)
(Depth : 340 mm)123
D86 104 122
E123 105 87
F980
Mass: kg 49
continued
 
						

							44GB
Formats supported by this 
stand
Digital input formats supported by this stand are 
as follows.
* Linear PCM accepts sampling frequencies of no 
more than 48 kHz.
Amplifier section
Rated Output Power
Stereo mode 50 W + 50 W, 6 ohms, 
1 kHz, THD less than 1 %
Reference Output Power
Surround mode  Front: 70 W/ch, 6 ohms, 
(per channel) 1 kHz, THD 10 %
Center*: 70 W, 3 ohms, 
1 kHz, THD 10 %
Surround*: 70 W/ch, 
6 ohms, 1 kHz, THD 10 %
Subwoofer: 120 W, 
3 ohms, 100 Hz ,THD 10 %
* Depending on the sound field settings and the source, 
there may be no sound output.
Inputs (Analog)
TV Sensitivity: 450 mV
Impedance: 30 kohms
Inputs (Digital)
TV, DVD Optical
SAT/CATV Coaxial, optical
Tuner section
System PLL quartz-locked digital 
synthesizerFM tuner section
Tuning range 87.5 – 108.0 MHz
(50 kHz step)
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range 531 kHz – 1,602 kHz (with 
the interval set at 9 kHz)
Antenna (aerial) AM loop antenna (aerial)
Intermediate frequency 450 kHz
HDMI section
Connector HDMI 19pin-standard 
connector
Video inputs/outputs SAT/CATV, DVD, BD: 
640 × 480p@60 Hz
720 × [email protected]/60 Hz
1280 × [email protected]/60 Hz
1920 × [email protected]/60 
Hz
1920 × [email protected]/60 
Hz
720 × 576p@50 Hz
1280 × 720p@50 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
Audio inputs SAT/CATV, DVD, BD: 
Linear PCM 7.1ch/
Dolby Digital/DTS
Speakers
Front speaker unit
Speaker system Full range, Bass reflex
Speaker unit 50 mm, cone type
Center speaker unit
Speaker system Full range, Acoustic 
suspension
Speaker unit 35 mm, cone type × 3
Surround speaker unit
Speaker system Full range, Bass reflex
Speaker unit 50 mm, cone type
Subwoofer unit
Speaker system Subwoofer, Bass reflex
Speaker unit 100 mm, cone type × 2
Format Supported/Not supported
Dolby Digitala
DTSa
Linear PCM-2ch*a
Linear PCM-7.1ch 
48k* (Only on HDMI)a
Linear PCM-7.1ch 
96k×
Dolby Digital Plus ×
Dolby True HD ×
DTS-HD ×
 
						

							45GB
Additional Information
General
Power requirements  220 – 240 V, 50/60 Hz
Power consumption
On: 110 W
Active Standby (power saving function is on 
and the TV connected to the stand is in standby 
mode): 0.5 W or less
Standby (Control for HDMI is off): 0.3 W or 
less 
Dimensions (approx.) 1,115 × 500 × 400 mm
(w/h/d)
Mass (approx.) 49 kg
Supplied accessories
Optical cable (1)
Remote commander (RM-ANU032) (1)
Size AA (R6) batteries (2)
Cable ties (2)
Shelf board (1)
Shelf support pins (4)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
Operating Instructions (1)
Design and specifications are subject to change without 
notice.
Dolby Digital
This movie theater sound format is more 
advanced than Dolby Surround Pro Logic. In this 
format, the surround speakers output stereo 
sound with an expanded frequency range, and a 
subwoofer channel for deep bass is 
independently provided. This format is also 
called “5.1” with the subwoofer channel 
designed as the 0.1 channel (since it functions 
only when a deep bass effect is needed). All six 
channels in this format are recorded separately 
for superior channel separation. Furthermore, 
since all the signals are processed digitally, less 
signal degradation occurs.
Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth 
output channels from 2 channel sources. This is 
done using an advanced, high-purity matrix 
surround decoder that extracts the spatial 
properties of the original recording without 
adding any new sounds or tonal colorations.
DTS
Digital audio compression technology 
developed by Digital Theater Systems, Inc. This 
technology conforms to 5.1-channel surround. 
This format comprises of stereo rear channel and 
there is discrete subwoofer channel in this 
format. DTS provides the same 5.1 discrete 
channels of high quality digital audio. The good 
channel separation is realized due to the all 
channel data being recorded discretely and 
processed in digitally.
HDMI
HDMI (High-Definition Multimedia Interface) 
is an interface that supports both video and audio 
on a single digital connection, allowing you to 
enjoy high quality digital picture and sound. The 
HDMI specification supports HDCP (High-
bandwidth Digital Contents Protection), a copy 
protection technology that incorporates coding 
technology for digital video signals.
 Standby power consumption 0.3 W.
 Halogenated flame retardants are not used in the 
certain printed wiring boards.
 Over 85 % power efficiency of amplifier block is 
achieved with the full digital amplifier, S-Master.
Glossary
continued
 
						

							46GB
PCM (Pulse Code Modulation)
A method of converting analog audio to digital 
audio for easy enjoyment of digital sound.
S-Force PRO Front Surround
Sony’s long-term involvement in surround 
technology (and the vast amounts of acoustic 
data accumulated as a result) has led to the 
development of all-new processing method and 
advanced DSP to handle this task effectively, 
which we call S-Force PRO Front Surround. 
Compared with previous front surround 
technologies, S-Force PRO Front Surround 
reproduces a more convincing sense of distance 
and space, resulting in a true surround sound 
experience without the need for rear speakers.
S-Master
S-Master is an all-digital amplifier technology 
developed by Sony, which effectively minimizes 
the occurrence of sound fragmentation and jitter, 
delivering superb dialog clarity and faithful 
reproduction of the original sound. The compact 
amplifier section supports a higher power 
efficiency and improved thermal performance.
x.v.Colour
“x.v.Colour” enables the more faithful 
reproduction of various colors such as the 
brilliant colors of flowers and the turquoise blue 
of the southern ocean.
 
						

							47GB
Additional Information
A
A/V SYNC 38
AMP menu
 37
AUDIO DRC
 39
B
Blu-ray Disc player (recorder)
connecting
 13
D
DIGITAL MEDIA PORT
connecting
 17
DISPLAY
 27, 39
DUAL MONO
 38
DVD player (recorder)
connecting
 13, 15
N
NIGHT mode 30
P
“PlayStation 3”
connecting
 13
R
Radio 25
Radio stations
 24
Remote
before use
 8
operating
 21
S
Satellite tuner
connecting
 13, 15
Setting
 9
S-Force PRO Front Surround
 7
Sleep timer
 40
Sound field
 28
Index
 
						

							Sony Corporation   Printed in Malaysia
(1)