Sony Projector VPL-VW665 User Manual

							41
Network Setting Perform internet protocol settings.
IPv4 SettingIP Address Setup: Selects the IP address setting method.
Auto (D HCP): The IP address is assigned automatically from the 
DHCP server such as a router.
Manual: Specifies the IP address manually.
When “Manual” is selected for “IP Address Setup,” select the item 
with the 
						

							42
Information Menu
The Information menu displays the model name, serial number, input signal type, software 
version and the cumulated hours of usage of the lamp.
You cannot adjust or change the displays listed above.
This unit has default image data to adjust preset data for input signals appropriately according 
to the signals shown in “Preset Signals” (page 57) (the preset memory). When the preset signal 
is input, the unit automatically detects the signal type and recalls the data for the signal from 
the preset memory to adjust it to an optimum picture. The signal type is displayed in the 
Information  menu.
Depending on the computer input signal, parts of screen may be hidden or displayed incorrectly.Items Description
Model Name Displays the model name
Serial No. Displays the serial number.
Signal type Displays the type of the input signal. When input signals with 3D 
information are input, the type of input signals and the 3D format are 
displayed.
Software Version Displays the software version.
Lamp Timer Indicates how long the lamp has been turned on (total usage).
Note
About the Preset Memory
Note
Model name
Serial No.
Software version Signal type 
						

							43
Connection to the network allows you to 
operate the following features:
 Checking the current status of the unit 
via a Web browser.
 Making the network settings for the 
unit.
 Network monitoring and controlling 
with control protocol (SDAP 
[Advertisement], SDCP [PJ Talk], 
DDDP [AMX], Crestron RoomView, 
Control4).
 When connecting this projector with the 
network, consult with the person who sets up 
the network. The network must be secured.
 When using this projector connected with the 
network, access the Control window via a 
Web browser and change the access 
limitation of the factory preset values 
(page 45). It is recommended to change the 
password regularly.
 When the setting on the Web browser is 
completed, close the Web browser to log out.
 The menu displays used for the explanation 
below may be different depending on the 
model you are using.
 Supported Web browsers are Internet 
Explorer 8/9/10/11.
 The menu displays only English.
 If the browser of your computer is set to [Use 
a proxy server] when you have access to the 
unit from your computer, click the check 
mark to set accessing without using a proxy 
server.
 AMX DDDP is not compatible with IPv6.
 These network functions are available when 
the unit is turned on.
Displaying the 
Control Window of 
the Unit with a Web 
Browser
1Connect the LAN cable.
2Set the network settings for the unit 
using “Network Setting” on the 
Installation  menu 
(page 41).
3Start a Web browser on the computer, 
enter the following in the address field, 
then press the Enter key on your 
computer.
http://xxx.xxx.xxx.xxx
(xxx.xxx.xxx.xxx: IP address for the 
unit)
When connecting by the IPv6 
address
http://[xxxx:xxxx:- xxxx]
You can confirm the IP address of the 
unit under “Network Setting” on the 
Installation  menu.
The following window appears in the 
Web browser:
Using Network Features
NotesLAN 
Connector LAN cable 
(straight type) 
(not supplied)
Hub, router, etc. 
						

							44
Once you make the network settings, 
you can open the Control window only 
by performing step 3 of this procedure.
Operating the 
Control Window
Click one of the Page Switching buttons to 
display the desired setting page.
You can limit a user for accessing any 
particular page.
Administrator: Allowed access to all 
pages
User: Allowed access to all pages 
except the Setup page
When you access the Setup page for the first 
time, input “root” as the user name and 
“Projector” as the password in the 
authentication dialog.
When you log in for the first time, the 
window that prompts you to change the 
password is displayed. Follow the 
instructions on the screen to change the 
password.
The name of the administrator is preset to 
“root.”
Switching the Page
Setting the Access Limitation
Page Switching buttons 
						

							45
The password can be changed in the 
Password page in the Setup page.
When you change the password, input a new 
password after deleting the password 
(*****) that was set.
The password of the administrator and user 
should be 8 to 16 characters that includes 
both alphabet and numeric characters. 
Alphabet is case-sensitive.
The default password “Projector” cannot be 
set as a new password. 
If you forget your password, consult with 
qualified Sony personnel.
You can confirm the current settings for the 
unit on the Information page.
Note
Confirming the Information 
Regarding the Unit
Entry area for [Administrator]
Entry area for [User]
Information area 
						

							46
Troubleshooting
If the unit appears to be operating erratically, try to diagnose and correct the problem using the 
following instructions. If the problem persists, consult with qualified Sony personnel.
Power
Picture
Error Handling
SymptomCause and RemedyPage
The power is not turned 
on.The power may not turn on if you turn the power off with ?/
1 (ON/STANDBY) button and turn it on again in a short 
time. After about 1 minute, turn the power on.–
Close the lamp cover securely, then tighten the screws 
securely.53
Check warning indicators. 49
The power is suddenly 
turned off.Check that “Power Saving” in the Setup   menu is set to 
“Standby.”35
Set “Power Saving” to “Off.” 35
SymptomCause and RemedyPage
No picture. Check that the connecting cable is connected to the external 
equipment properly.
Depending on the external equipment, the unit may not 
function correctly via the HDMI 1 connector. In this case, 
use the HDMI 2 connector, then select the input.13
Select the input source correctly using the INPUT button. 15
Check that the computer signal is set for output to an 
external monitor.
If the notebook computer, etc., signal is output to its display 
and an external monitor, the external monitor’s image may 
not be displayed correctly. Set your computer to output the 
signal to only an external monitor.–
The picture has ghosts. Video images are displayed in 3D. Watch the 3D video 
images using the 3D glasses, and set “2D-3D Display Sel.” 
to “3D.” 
To convert 3D video images to 2D video images, set “2D-
3D Display Sel.” to “2D.”16, 36
Bright or dark area of the 
video appears too bright 
or too dark.This symptom may occur when signal level other than those 
of HDMI standard is input. Switch the output level of the 
connected equipment, or switch the Dynamic Range on the 
Function   menu of the unit.37
The picture is too dark. Adjust “Contrast” or “Brightness” on the Picture   menu 
properly.27
The picture is not clear. Adjust the focus. 9
Condensation has accumulated on the lens. Leave the unit 
for about 2 hours with the power on.– 
						

							47
On-screen display
Remote control
The color of characters or 
the picture is not 
appropriate.Select the desired color registration in “Panel Alignment” of 
the Installation   menu.40
Image is left on the 
screen. (image retention)When high contrast non-moving images are displayed for a 
long period of time, there may be some image retention on 
the screen. This is only a temporary condition. Turning off 
the power for a while will eliminate the retained image.–
SymptomCause and RemedyPage
On-screen display does 
not appear.Set “Status” on the Setup   menu to “On.” 34
Check if the ON/STANDBY indicator should light in green. 
When the ON/STANDBY indicator blinks in green, the unit 
is starting up. Wait until it stops blinking and remains lit in 
green.8
The model name does not 
disappear from the 
screen.The display mode of the unit may be set at the time of 
purchase. Consult with your local dealer or qualified Sony 
personnel.–
SymptomCause and RemedyPage
The remote control does 
not work.Batteries could be weak. Replace them with new batteries. –
Insert the batteries with the correct polarities. –
If there is a fluorescent lamp near the remote control 
detector, the unit may work improperly or inadvertently.–
Confirm the position of the remote control detector on the 
unit.4, 5
Set “IR Receiver” to “Front & Rear” on the Installation   
menu.39
SymptomCause and RemedyPage 
						

							48
3D video images
Others
SymptomCause and RemedyPage
The video image does not 
seem like 3D video 
images.Check if the 3D glasses are turned on. 16
Make sure that the battery in the 3D glasses could be weak 
or is sufficiently charged.–
Set “2D-3D Display Sel.” to “Auto” or “3D.” 36
Check if the input signals are compatible 3D signals. 60
The 3D signals may not be input depending on the 
specifications of the connected AV selector/AV amplifier/
external equipment. If the 3D signal is not input, confirm 
the specifications and/or settings of the AV selector/AV 
amplifier/external equipment.–
When the viewing position is too far from the unit, the 3D 
glasses may not be able to display the images properly.16
The screen size is not appropriate. Set the zooming 
magnification to low or watch the image from farther away 
from the screen.65
For details, see “Precautions for use” of “Using the 3D 
Glasses.”16
SymptomCause and RemedyPage
The fan is noisy. Check the setting of “High Altitude Mode” on the Setup 
  menu.34
Make sure that the room temperature is not too high. –
Check the installation requirements of the unit.
Fan speed increases to maintain the product reliability of the 
projector’s components in a room, where the temperature is 
higher than normal. The fan noise becomes slightly louder. 
The approximate normal temperature is 25°C (77°F).–
The lens shift cannot be 
adjusted.The lens shift cannot be adjusted over the range of 
movement. Adjust the lens shift within the range of 
movement.11, 65 
						

							49
Warning Indicators
The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with 
your projector.
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Flashing/Lighting indicatorsThe number of 
flashesCause and Remedy
Twice Close the lamp cover securely, then tighten 
the screws securely (page 53).
Three times The temperature of lamp is unusually high. 
Turn off the power and wait for the lamp to 
cool, then turn on the power again.
If the symptom persists, the lamp may be at 
the end of its service life. In this case, 
replace the lamp with a new one (page 52).
Twice The internal temperature is unusually high. 
Check to ensure that if nothing is blocking 
the ventilation holes or whether or not the 
unit is being used at high altitudes.
Three times The fan is broken. Consult with qualified 
Sony personnel.
Note
ON/STANDBY 
indicatorWARNING 
indicator
(Flashes in red)
(Flashes in red)
(Flashes in red)
Both indicators flash 
						

							50
Message Lists
Warning messages
Caution messages
SymptomCause and RemedyPage
High temp.! Lamp off in 
1 min.Turn off the power. –
Check to ensure that nothing is blocking the ventilation 
holes.4, 5
Frequency is out of 
range!Frequency is out of range. Input a signal that is within the 
acceptable frequency range of the unit.57
Please replace the Lamp. It is time to replace the lamp. Replace the lamp.
If this message appears again after you replace the lamp, the 
lamp replacement process is not complete. Check the lamp 
replacement process.
To clear this message, press any button either on the remote 
control or the control panel of the unit once.52
Projector temperature is 
high. High Altitude 
Mode should be “On” if 
projector is being used at 
high altitude.Check to ensure that nothing is blocking the ventilation 
holes.4, 5
When using the unit at high altitude, set “High Altitude 
Mode” to “On.”
When temperature inside the unit remains high, “High 
Altitude Mode” is switched to “On” in 1 minute, then the 
fan speed increases.34
Power Saving Mode is 
set. Projector will 
automatically enter 
Standby Mode in 1 
minute.“Power Saving” is set to “Standby.”
If no signal is input, the power turns off after 1 minute, and 
the projector goes into standby mode.35
SymptomCause and RemedyPage
No signal is input in the selected input. Check connections. 13
Not applicable! Press the appropriate button.
The operation to be activated by the button is currently 
prohibited.–
Settings Lock enabled. “Settings Lock” is set to “Level A” or “Level B.” 37
Note
Note
Note
x