Sony Projector VPL-SW535C User Manual

31Using Network Features
Network
SMTP Authentication: Check this 
check box to arrange for SMTP 
authentication to be performed before 
sending e-mail.
Account Name: Enter the mail account 
name.
Password: Enter the password.
5Confirm the contents of the e-mail 
report.
When you click on [View], the contents 
of the e-mail report are displayed.
6Send the test mail.
Check on the Send test mail check box 
then click on [Apply] to send your test 
mail to the e-mail address you set.
 The email report...

32Using Interactive Function
BInteractive Function
Using Interactive Function
The Interactive function (VPL-SW535C/SW525C only) enables you to do the following: 
 Draw shapes/write text on the screen with the Interactive Pen Device.
 Use the Interactive Pen Device as a mouse on the projected screen.
The Interactive Presentation function works by a detector in the projector, which picks up infrared 
rays emitted from the tip of the Interactive Pen Device. Observe the precautions noted below.
 Avoid...

33Using Interactive Function
Interactive Function
1Insert the supplied CD-ROM into the 
CD-ROM drive of the computer.
Open the CD-ROM and double-click 
[InteractivePresentationUtility.exe].
Close all running applications, then start the 
installation.
2Follow the on-screen instructions to 
install the software.
To uninstall Interactive Presentation 
Utility, click [Start]-[All Programs]-
[Interactive Presentation Utility]-
[Uninstall].
To start Interactive Presentation Utility, click 
[Start]-[All...

34Using Interactive Function
Make sure you touch the center of the dot, 
otherwise positioning may be offset.
When starting Interactive Presentation 
Utility, the toolbar is displayed.
Interactive mode
Mouse/Pen
Switch the Interactive Pen function 
between mouse and drawing pen.
Whiteboard mode
Page up
Page down
Highlight*
Pen/Eraser*
Switch between pen and eraser.
Fast Pen Set*
Accurate Pen Set*
Draw free lines*
Draw straight lines*
Draw circles*
Draw rectangles*
Undo
RedoClear the desk annotation
Clear...

35Using Interactive Function
Interactive Function
View List
Display a list of white board images that 
are being edited.
more…
more…
Print preview
Print current page
Time and date stamp
Browse
Jump to first page
Jump to first page.
Jump to last page
Jump to last page.
Go to previous page
Go to next page
Replay current page
Replay to end page
Complete replay
Skip the playback of the current page.
Stop replaying 

36Indicators
BOthers
Indicators
The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table 
below.
ON/STANDBY indicator
LAMP/COVER indicator
StatusMeaning/Remedies
Lights in red The projector is in Standby mode.
Flashes in green  The projector is ready to operate after having been turned on. 
 The lamp cools after the projector is turned off.
Lights in green The projector’s...

37Messages List
Others
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessagesMeaning/RemedyPage
High temp.! Lamp off in 
1 min.Check the items below.
 Check if nothing is blocking the ventilation holes.
 Check if the air filter is not clogged.
 Check if the Installation Attitude in the Installation menu is 
set correctly.4, 4, 
26, 42
Frequency is out of 
range!Change the output setting of the connected...

38Troubleshooting
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the 
instructions below.
SymptomsRemedyPage
The power is not turned 
on.Check if the AC power cord is firmly connected. –
When the “Panel Key Lock” is set to “On,” you cannot turn on 
the projector using the ?/1 key on the projector.23
If the lamp or lamp cover is not attached securely, the projector 
cannot be turned on.40
If the air filter or air filter cover is not attached securely,...

39Troubleshooting
Others
The image is not clear. Check if the projector is in focus. 14
The picture will not be clear if condensation has accumulated 
on the lens. In this case, let the projector sit for about two 
hours with the power on.–
The image is noisy. Check if the connecting cable is connected to the external 
equipment properly.9
No sound. Check that the connecting cables between the projector and 
external video or audio equipment are securely connected.9
Check if the external audio equipment...

40Replacing the Lamp
Replacing the Lamp
Replace the lamp with a new one if a message displayed on the projected image or the LAMP/
COVER indicator notifies you to replace the lamp (pages 36, 37).
Use an LMP-E212 projector lamp (not supplied) for replacement.
 The lamp remains hot after the projector is 
turned off. If you touch the lamp, you may 
burn your finger. When you replace the 
lamp, wait for at least an hour after 
turning off the projector for the lamp to 
cool sufficiently.
 Do not allow any...