Sony Projector Vpl Hs50 User Manual

							11Step 1: Installing the Projector
Connections and PreparationsWhen using the 16:9 aspect ratio screen
Unit: mm (inches)
To calculate the installation measurements (SS: Screen Size)
a (minimum) = {(SS × 21.27/0.7227) – 35.160899} × 1.025
b (maximum) = {(SS × 33.9409273/0.7227) – 37.678872} × 0.975
c = (SS/0.7227 × 9)
d = (SS/0.7227 × 8)
e = (SS/0.7227 × 4.5)
When using the 4:3 aspect ratio screen
Unit: mm (inches)
To calculate the installation measurements (SS: Screen Size)
a (minimum) = {(SS × 21.27/0.5906) – 35.160899} × 1.025
b (maximum) = {(SS × 33.9409273/0.5906) – 37.678872} × 0.975
c = (SS/0.5906 × 9)
d = (SS/0.5906 × 8)
e = (SS/0.5906 × 4.5)
Screen size 
(inches)40 60 80 100 120 150 180 200
a (minimum) 1170
(46
 1/8)1770
(69 3/4)2380
(93 3/4)2980
(117 3/8)3580
(141)4490
(176 7/8)5390
(212 1/4)6000
(236 1/4)
b (maximum) 1790
(70
 1/2)2710
(106 3/4)3630
(143)4540
(178 7/8)5460
(215)6830
(269)8210
(323 3/8)9120
(359 1/8)
c 498
(19
 5/8)747
(29 1/2)996
(39 1/4)1245
(49 1/8)1494
(58 7/8)1868
(73 5/8)2241
(88 1/4)2491
(98 1/8)
d 443
(17
 1/2)664
(26 1/4)886
(35)1107
(43 5/8)1328
(52 3/8)1660
(65 3/8)1992
(78 1/2)2214
(87 1/4)
e 249
(9
 7/8)374
(14 3/4)498
(19 5/8)623
(24 5/8)747
(29 1/2)934
(36 7/8)1121
(44 1/4)1245
(49 1/8)
Screen size 
(inches)40 60 80 100 120 150 180 200
a (minimum) 1440
(56
 3/4)2180
(85 7/8)2920
(115)3660
(114 1/8)4390
(172 7/8)5500
(216 5/8)6610
(260 3/8)7350
(289 1/2)
b (maximum) 2200
(86
 5/8)3330
(131 1/8)4450
(175 1/4)5570
(219 3/8)6690
(263 1/2)8370
(329 5/8)10050
(395 3/4)11170
(439 7/8)
c610
(24
 1/8)914
(36)1219
(48)1524
(60)1829
(72 1/8)2286
(90 1/8)2743
(108 1/8)3048
(120 1/16)
d542
(21 3/8)813
(32 1/8)1084
(42 3/4)1355
(53 3/8)1626
(64 1/8)2032
(80 1/16)2438
(96)2709
(106 3/4)
e305
(12
 1/8)457
(18)610
(24 1/8)762
(30)914
(36)1143
(45)1372
(54 1/8)1524
(60) 
						

							12Step 1: Installing the Projector
2 Position the projector so that the lens is parallel to the screen.
3Project an image on the screen and adjust the picture so that it 
fits the screen. (1 page 17)
To project an image, connect video equipment to the projector. (1 page 
13)
When using a screen with an uneven surface, stripes pattern may rarely appear on the 
screen depending on the distance between the screen and the projector or the zooming 
magnifications. This is not a malfunction of the projector.
For installation of the projector on a ceiling, see “Ceiling Installation.” (1 
page 58)
Note
Screen
Top view 
						

							13Step 2: Connecting the Projector
Connections and PreparationsStep 2: Connecting the Projector
When making connections, be sure to do the following:
 Turn off all equipment before making any connections.
 Use the proper cables for each connection.
 Insert the cable plugs properly; plugs that are not fully inserted often 
generate noise. When pulling out a cable, be sure to pull it out from the plug, 
not the cable itself.
 Refer to the operating instructions of the connected equipment.
To connect to a DVD player/recorder or digital tuner equipped with 
component video connectors
Tip
To connect the projector to a DVD player/recorder, digital tuner, etc. which is not 
equipped with component video connectors, use the S video cable to connect to the S-
video output of the DVD player/recorder, digital tuner, etc. If the connected equipment 
is not equipped with the S-video output connector, use the video cable to connect to the 
video output jack on the equipment.
Connecting to a DVD Player/Recorder or Digital Tuner
S VIDEO YPB/CBPR/CRVIDEOHDMIINPUT
PB/
 CBPR/CRYPB/
 CBPR/CRY
Component video cable (not supplied)
: Video signal flowDVD player/recorder, 
digital tuner, etc., with 
component video 
connectors Rear of the projectorAV amplifierSpeakers 
						

							14Step 2: Connecting the Projector
To connect to a DVD player/recorder equipped with HDMI 
output
You can enjoy better picture quality by connecting a DVD player/recorder 
equipped with HDMI output to the HDMI input of the projector.
YPB/CBPR/CRVIDEOHDMIINPUT
HDMI cable (not supplied)
: Video signal flow Rear of the projector
DVD player/recorder, 
etc., with the HDMI 
output
to HDMI output AV amplifier
Speakers
............................................................................................................................................................
HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered 
trademarks of HDMI Licensing LLC. 
						

							15Step 2: Connecting the Projector
Connections and Preparations
You can connect a DVD player/recorder which is not equipped with 
component video connectors, hard disk video recorder, VCR or laser disk 
player. See also the instruction manual of each equipment.
Tip
If you do not know to which connector you should connect the cable, S VIDEO (S video 
connector) or VIDEO (video connector), connect it to S VIDEO to enjoy better picture 
quality.
If the equipment to be connected has no S video connector, connect the cable to the 
video output.
Connecting to Video Equipment
S VIDEOINPUT APR/CRVIDEOINPUT
S video or video cable (not supplied)
: Video signal flowRear of the projector
to S video or 
video outputVideo equipmentAV amplifier Speakers 
						

							16Step 2: Connecting the Projector
Tip
Set “Input A Signal Sel.” in the Setup   menu to “Auto” or “Computer.” If the input 
signal does not appear properly, set it to “Computer.”
If you set your computer, such as a notebook type, to output the signal to both your 
computer’s display and an external monitor, the picture of the external monitor may not 
appear properly. Set your computer to output the signal to only the external monitor.
For details, refer to the computer’s operating instructions supplied with your computer.
Connecting to a Computer
Note
S VIDEOINPUT APR/CRVIDEOINPUT
HD D-sub 15-pin cable (not supplied)
: Video signal flow Rear of the projector
to monitor outputComputer 
						

							17Step 3: Adjusting the Picture Size and Position
Connections and PreparationsStep 3: Adjusting the Picture Size and 
Position
Project an image on the screen and then adjust the picture position.
Tip
The I/1 (on/standby), INPUT, MENU, and M/m/
						

							18Step 3: Adjusting the Picture Size and Position
2Press the I/1 (on/standby) switch to turn on the projector.
The ON/STANDBY indicator lights in green.
3Turn on the equipment connected to the projector.
Refer to the operating instructions of the connected equipment.
4Press INPUT to project the picture on the screen. 
Each time you press the button, the input indication changes. (1 page 24)
Tip
When “Auto Input Search” is set to “On” in the Function   menu, the channel 
of the signal input is automatically displayed.
5Move both LENS SHIFT dials to adjust the picture position.
ON/
STANDBY
Lights in green.
VideoINPUT
LENS SHIFT
To adjust the vertical 
position
To adjust the horizontal position 
						

							19Step 3: Adjusting the Picture Size and Position
Connections and PreparationsTo adjust the horizontal position
Turn the LENS SHIFT dial right or left.
The picture moves right or left by a maximum of half of the screen size from 
the center of the lens.
To adjust the vertical position
Turn the LENS SHIFT dial up or down.
The picture moves up or down by a maximum of the screen size from the 
center of the lens.
Top view
: Picture position when moving the 
picture to the left at maximum
: Picture position when moving the 
picture to the right at maximum1/2H1H1/2H
Side view
: Picture position when moving the 
picture upward at maximum
: Picture position when moving the 
picture downward at maximum
1V
1V
1V 
						

							20Step 3: Adjusting the Picture Size and Position
When you use the horizontal and vertical lens shift features at the same time, you 
can move the picture vertically by a maximum of half of the screen size.
6Adjust the picture size using the zoom ring.
7Adjust the focus using the focus ring.
To adjust the tilt of the installation surface
If the projector is installed on an uneven surface, use the adjusters to keep the 
projector level.
Note
Zoom ring
Focus ring
AdjustersTurn to adjust.